查询词典 The Influence

Reductive conversion of geraniol to citronellol is adopted as a model reaction, and several factors in the reaction are discussed using gas chromatography method. The influence of n-hexane and butyl acetate, as organic solvents, on biocompatibility was studied; the influence of methanol, ethanol, glycol, n-butanol and 1-hexanol, as energy substance, on the transformation efficiency was compared, respectively; the catalysis capabilities of Baker's yeast, XST-KO yeast, LP yeast, alcohol yeast, dry yeast, Saccharomyces cerevisiae, Angel yeast and Meishan yeast were discussed. It has been proved that biocompatibility of n-hexane are much better than that of butyl acetate, and the hexane has been demonstrated the most effective in terms of the influence on biotransformation, Baker's yeast has shown the highest tranformation efficiency among the eight yeast strains.

以香叶醇转化为香茅醇作为模型反应，通过气相色谱法进行定性和定量分析研究了影响该有机相生物转化反应的几个基本因素，考察了两种有机溶剂正己烷和乙酸丁酯对生物相容性的影响，选用甲醇、乙醇、乙二醇、正丁醇和l-己醇分别作为能量物质进行实验，比较其对转化的影响并探讨了Baker's酵母、XST-KO酵母、LP酵母、酒精酵母、假丝酵母、干酵母、安琪酵母和梅山酵母八种不同酵母作为生物催化剂对模型反应的催化能力，结果表明，正己烷作为有机溶剂，其生物相容性明显好于乙酸丁酯，更加有利于该生物转化反应进行；乙二醇作为能量物质，该模型反应转化率最高；而 Baker's酵母作为生物催化剂，对该模型反应的催化能力最强，最适合作为该模型反应的催化剂。

Glyphosate brought the biggest vice-effects, clethodim took the second and fenoxaprop-p-ethyake minimum:(1)As to the pure growth, MDA accumulation, the relative permeability of plasma membrane and chlorophyll content, glyphosate had evident influences on them in the daily dosage, 1/2 and 1/4 of the daily dosage . The walnut seedling dried and died twenty days later.(2)The influences of clethodim in different concentration such as double daily dosage, daily dosage and 1/2 of daily dosage on the above four indexes demonstrated differently, the more concentration was, the more severe the influence. was. With the concentration reducing, the influence weakened gradually.(3) Double daily dosage, daily dosage and 1/2 daily dosage of fenoxaprop-p-ethy exerted a slight vice-influence to the MDA accumulation, the relative permeability of plasma membrane and chlorophyll content.

1用草甘膦常用量、1/2倍常用量、1/4倍常用量处理之后，对核桃苗新梢生长量、叶片中丙二醛含量、膜相对透性以及叶片中叶绿素含量的影响最大，几乎所有样枝的新梢在药后20天后都发生干枯及死亡现象；(2)用收乐通2倍常用量、常用量、1/2倍常用量处理之后，对核桃苗的新梢生长量、叶片中丙二醛含量、膜相对透性及叶片中叶绿素含量的影响，呈现出浓度不同影响亦不同的现象，浓度越大，影响越明显，随着浓度的降低，影响也逐渐减弱；(3)用威霸2倍常用量、常用量、1/2倍常用量处理之后，对核桃苗新梢生长量、叶片中丙二醛含量、膜相对透性及叶片中叶绿素含量的影响最小；(4)三种除草剂对核桃苗的影响随着药后时间的延长，其影响在逐渐减小。

This paper studies the main geometrical parameter such as angle, height, width, stagger and the upper width in dentation and trapezoid flow path, firstly, uses the single-phase numerical simulation of the computational fluid dynamics technique to analyse the influence of different geometrical parameter on discharge coefficient and flow state exponent of drip emitter. Secondly, uses the two-phases numerical simulation of CFD (1% sand content ) to analyse the influence of the above mentioned geometrical parameter on the contribution regulation of sand and anti-clogging performance. Thirdly, uses the PIV （ particle Tracking Velocimetry ） technique which can see the small-scale flow path to observe and test the trajectories and velocities of solid particles in labyrinth flow path, and analyses the basic factors which can influence the movement characteristic of solid particles and the flow state in flow path.

本文以齿形流道、梯形流道为主要研究对象，以流道转角、流道高，流道宽、偏差量及梯形流道上底宽为主要结构参数，首先应用 CFD 单相流数值模拟技术对不同结构参数灌水器流道水力性能进行模拟，分析了不同结构参数对流态指数和流量系数的影响，其次，应用 CFD 两相流（含沙量为1%）数值模拟技术分析了结构参数对含沙量分布规律和抗堵塞性能的影响，然后，应用 PIV 可视化测试方法测试了固体颗粒在流道内运行轨迹及速度，分析了影响固体颗粒运动特性及流道内流体流态的基本因素，最后，对上述流道结构形式通过模具加工及滴灌带试制，进行了标准化测试（ GB/T 17187-1997 农业灌溉设备滴头技术规范和试验方法与 ISO 标准 ISO /TC23 /SC18 /WG5N4短周期堵塞测试程序），测试结果验证了 CFD 模拟结果，并提出了迷宫结构流道灌水器的抗堵塞设计方法。

This paper studies the influence of country economy guideline in power demand. According to identifying the main economy and society factors in affecting the change of Fujian power demand, the power demand forecast model is proposed. And the demand curve models fitting for diversified users are built by researching the influence of electrovalence to power demand.The influence of demand side management in load characteristic of Fujian power system is analysed.Used the arithmetic of modifying the history load curve, this paper forecast the changing and development trend of Fujian load characteristic.

本文研究了国民经济指标对电力需求的影响，通过识别影响福建省电力需求变化的主要经济社会因素，建立电力需求预测模型；研究了电价变化对电力需求的影响，对各类用户建立适合各自特点的需求曲线模型；分析了需求侧管理对福建电网负荷特性的影响，采用历史负荷曲线修正法，预测了福建电网负荷特性的变化发展趋势。

Combined with the surge-chamber ground swell calculation of some plants, get the numerical value of the influence of the superimposition and the superpose time; From the calculation of the plate pressure difference of the throttled surge chamber, analyze the numerical value of the influence of the superimposition on it.Chapter 5: Based on the analytic calculation of water hammer, indicate the linear pressure distribution in the diversion pipe system and the calculation operation of its maximum numerical value, combined with some project instances, analyze the the influence of the superimposition on it behind and before the surge-chamber.Chapter 6: Summarize the whole paper, and present the future research directions and emphasis.

结合具体电站的调压室涌浪计算，得到波动叠加带来的影响大小及叠加时间；并从阻抗式调压室底板压差的计算出发，分析波动叠加对底板压差的影响大小及叠加时间；第5章，在前人对水击压力的解析计算的基础上，阐述水电站引水发电系统中水击压力分布及其最大压力对应的计算工况，结合工程实例，分析调压室前后，波动叠加对沿程压力分布的影响及其大小；第6章，总结全文，提出今后研究的重点和方向。

In the traditional GSM network planning, the revised Hata model serves as the prototype, and the coefficient in the model formula is tuned according to the data obtained in the radio propagation feature test specific to local actual radio environment, so as to obtain the propagation model for practical prediction. A common digital map only contains the clutter information and the digital terrain model information. So the building designers cannot fully allow for the influence of radio propagation, and can only estimate the influence on the building roughly from a traditional perspective, e.g., consider the influence of different clutters through certain clutter offset.

在传统的GSM网络规划中，一般都以修正的Hata模型为原型，再利用规划软件通过导入针对当地的实际无线环境做无线传播特性测试所得的数据对模型公式中的系数进行修正而得到实际预测用的传播模型，一般使用的数字地图仅包括地物信息和高程信息，因此建筑物对无线传播的影响无法充分考虑，只能从统计意义上对建筑物的影响进行粗略的估计，如通过一定的地物偏移来考虑不同地物的影响。

The influence of high temperature and high pressure on foaming agent's properties in opened and closed system, and influence of the change of foaming agent's properties on foaming capacity and foam stabilizing capacity are also studied. The multiple regression theory is used to establish the quantitative characteristic functions of foaming agent versus temperature and pressure. Based on the Gibbs Principle, the quantitative characterization is carried out on relation of foam system's free energy versus its surface tension, surface area and concentration, and the analysis of energy concluded that the disintegration of the foam is inconvertible. At the same time, the influence of change of foam's shape and structure on distribution of reservoir temperature and pressure is qualitatively described, and the coupling mechanism between temperature field, pressure field and chemical field is systematically expounded.

同时，研究了不封闭体系、封闭体系下高温、高压对发泡剂性质的影响，以及发泡剂性质的改变对其发泡性能、稳泡性能的影响；采用泡沫实验的相关结果，运用多元回归理论，建立温度、压力与发泡剂浓度的定量表征函数；基于Gibbs原理，对高温、高压下泡沫体系的自由能与其表面张力、体系中液体的表面积以及浓度关系进行定量化的表征研究，从能量的角度得出了泡沫衰变过程具有不可逆性；同时定性地描述了泡沫形态、结构的变化对油藏温度和压力分布的影响，系统地阐述了温度场、压力场、化学场间的耦合作用机理。

A method for identifying the damage, using the influence line curvature of deflection differential values at a point before and after the damage is proposed, that is, when the moving load is in the area without the damage, the influence line curvature is zero, however when the moving load is in the area with the damage, the influence line curvature evidently increases and has the relationship with the positions of the damage points and the rigidity of the beam before and after the damage.

提出利用损伤前、后某一点的挠度差值影响线曲率来识别损伤的方法，即当移动荷载位于无损区域时，挠度差值影响线曲率为0，当移动荷载位于有损区域时，挠度差值影响线曲率明显增大，且与损伤点的位置、损伤前后的刚度有关。

Firstly, the 3D solid model of the analyzed object is built directly in the FEM software ANSYS 8.0 without using other CAD software. The influence of the side sizes of solid elements on computing results and the influence of coupling ways between different parts on the modal parameters are researched by simply modeling. And a new connecting method about joints in ANSYS is proposed and applied to finite element modeling of the test-bed for spindle system. Furthermore, several different computing techniques for modal parameters extraction are compared in solving the finite element model of spindle system test-bed. Many modal solutions are also done to achieve the relationships between the whole or part stiffness value and computed modal parameters. The laws about joint rigid parameters" influences on modal parameters are discussed by means of altering their values for conjoint parts. And by changing local rigid parameter values, the different location selections" influence on computed modal parameters is also studied.

本文通过使用ANSYS 8.0软件直接建立研究对象的实体结构模型，而没有借助其他的CAD软件；通过构建简单的模型研究实体单元边长大小对计算结果的影响，部件之间不同的联结方式对模态参数的影响，探讨在ANSYS中实现结合部的方法，提出一种新的联结方法，并建立主轴系统试验台的有限元模型；对建立的主轴系统试验台有限元模型求解，比较几种不同模态提取方法；通过改变结合部联结单元的刚度参数进行的计算，寻找联结刚度对模态参数变化的影响规律；改变局部联结单元的刚度参数，研究刚度值位置差异对计算模态参数的影响。

Based on the abundant proof of the individual influence factor and the environmental influence factor of the air traffic controllers' stress, it combines the design of EAP and the influence factors of the controllers' stress, in order to relieve the controllers' stress effectively by the management of EAP and help the controllers to choose the correct coping style when facing stress. It provides strategy foundation to the creation of the harmonious working environment and the enhancement of the controllers' individual modulability.

在对空中交通管制员压力源的个人影响因素和环境影响因素的充分论证的基础上，将EAP设计与影响管制人员压力源因素有机结合起来，力求通过EAP措施帮助管制人员有效地缓解工作压力，帮助管制员面对压力时能够采取正确的应对方式；为创造和谐积极的组织工作环境和提高管制员个人自我调节能力提供决策依据。

Singer Leona Lewis and former Led Zeppelin guitarist Jimmy Page emerged as the bus transformed into a grass-covered carnival float, and the pair combined for a rendition of "Whole Lotta Love".

歌手leona刘易斯和前率领的飞艇的吉他手吉米页出现巴士转化为基层所涵盖的嘉年华花车，和一双合并为一移交&整个lotta爱&。

This is Kate, and that's Erin.

这是凯特，那个是爱朗。