查询词典 PCL

PCL could be separated into anterolateral bundle and posteromedial bundle and there were ＂functional bundles＂ in each of them, which guaranteed the rearward stability of tibia in normal range of motion of the knee.

前外侧束与后内侧束中均存在&功能束&，两者的&功能束&联合作用可基本维持膝关节活动范围内胫骨的后向稳定性，&功能束&止点与两束止点中心不吻合。

Newborn vessels were hard found in the PLA/PCL group at each time point. Twelve postoperative weeks, bone extremities sclerotized, and defect regions were fully filled by fiber tissues.

单纯聚乳酸／聚己内酯组各时间点新生血管少见，术后12周时骨端硬化，缺损区被纤维组织填充。

The rehabilitation process of semitendinosus autograft was as same as that of bone-patellar tendon-bone graft in reconstruction of PCL.

腱骨间愈合最终可形成直接止点，但在骨道内的不同部位所形成的止点成熟度不同。

Objective:To evaluate the short-term results of reconstruction of PCL、ACL with quadruple-stranded semitendinosus tendon and to discuss the key points of the surgery and postoperative rehabilitation.

目的：评价4股半腱肌肌腱重建交叉韧带的临床疗效。

METHODS: A retrospective analysis was performed in 76 patients underwent arthroscopic PCL reconstruction, with the use of B-TP-B autograft in 21 patients, B-TP-B allograft in 27 patients, semitendinosus tendon autograft in 28 patients.

回顾分析21例膝关节镜下自体骨-髌腱-骨移植、28例自体半腱肌腱移植和27例异体骨-髌腱-骨移植重建后交叉韧带的情况。

Hoffman-Lauritzen theory was used to analyze spherulitic growth kinetics and the free energy of the folding surface was derived.

由此可见，PEG链段对胶束的影响越小，PCL嵌段的影响越大，越趋向于形成片状晶体结构。

The first step: basic PV-ERP(PCL 400 ms,300 ms) was measured firstly. Stimulated distal pulmonary vein ten minutes by maximum frequency that 1:1 pacing pulmonary vein. PV-ERP was remeasured immediately, 5 min and 10 min, respectively.

对8条成年杂种犬采用自身前后对照的方法，第一部分实验：首先分别测量起搏周长分别为300 ms、400 ms时肺静脉有效不应期，接着以1：1起搏肺静脉的最快频率刺激肺静脉10 min，分别在刺激中止后即刻、5 min、10 min时重复测量PV-ERP。

Result: The joint gap of flexion and extension both increased after resecting PCL.

结果：后交叉韧带切除后可以使屈曲时内侧间隙增加5.12±1.48mm，外侧间隙增加4.91±0.95mm。

The system of measuring and controlling temperature and pressure that has been developed by Visual Basic Language based on the data acquisition card PCL-818HG is successfully applied in the extruding and blowing mold to measure the pressure in the extruding process and the part cold and solidification temperature and control the temperature of the extruding machine in real time.

在挤出的过程中，有加热、散热和产生热量的过程，在稳定的工作情况下，所有这些热量达到平衡从而使挤出物料的温度达到某一动态平衡，而压力对于物料的流变性能来说也是重要的影响因素，因此挤出过程的温度和压力很重要，需要实时测量。

PCL is a foreign founded company and it is responsible for providing concentrate to PepsiCo Bottlers in China and South East Asia.

本公司为外商独资企业，于一九八八年夏在广州经济技术开发区成立，产品主要供应百事国际集团在中国大陆建立的合资/合作灌瓶厂，兼顾销往香港等东南亚地区。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。