查询词典 Min

The insertion had three phases which grouped by the duration of pedipalps inserting.Initial long inserting duration about 25 min was followed by a medium inserting duration(15min or so);however,subsequent short inserting decreased to approximately 5 min in duration.

通过分析，发现了一种微蛛新的交配模式，即可将浅斑近微蛛的插入期分为三个阶段：首先是大约25 min长插入期，接着是一个大约15 min的中度插入期，最后是一个大约5 min的短插入期。

The programmed calcination process is necessary, that is, heating the as-elutedhmmersed oxalates mildly from room temperature to 300℃at a heating rate of 5℃/min, and keeping the samples at 300 C for 1 h; consecutively, heating to 900℃at 10℃/min, and then keeping for 4 h.

程控的烧结过程是必须的，这就是，按5度/分钟逐步加热按这种淋洗制备的草酸盐到300度，保温1小时；接着，按10度/分钟加热到900度，保温4小时。

In the preparation method, primary soybean oil and deep hydrogenation soybean oil, or primary rapeseed oil and deep hydrogenation rapeseed oil are adopted as raw materials; sodium methoxide is selected as a catalyst; the consumption of the catalyst is 0.1 percent to 0.5 percent; the reaction temperature is 70 DEG C to 110 DEG C; therefore, the primary soybean oil and the deep hydrogenation soybean oil, or the primary rapeseed oil and the deep hydrogenation rapeseed oil have randomized lactide reaction for 10 min to 90 min, so as to change the composition of mixed oil triglyceride and obtain the low/zero trans fatty acid base oil with different melting points and the characteristics of solid fat.

本发明以一级大豆油和极度氢化大豆油，或一级菜籽油和极度氢化菜籽油为原料，选择甲醇钠为催化剂，催化剂用量0.1％～0.5％，反应温度70～110℃，使一级大豆油和极度氢化大豆油，或一级菜籽油和极度氢化菜籽油之间进行随机交酯化反应，反应时间10～90min，从而改变混合油甘三酯组成，得到具有不同熔点和固体脂肪特征的低/零反式脂肪酸基料油。

Plackett-Burman experimental design and the uniform experimental design were used to select the main factors of the ball milling pretreatment of corn stalk. The experimental results were analyzed by data processing software and well-fitted regression equation was established. Effects of ball milling parameters, such as raw material diameter, speed, ratio of raw materials, grinding media and alternating time, on the enzymolysis were analyzed. The optimal parameters of ball milling pretreatment of the corn stalk were as follows: particle size of raw material of 0.5 mm, speed of 340 r/min, the raw material content of 3.4 g, the number of ball of 15 (Ф= 10.0 mm), alternating running time of 5 min.

研究了玉米秸秆水解过程中球磨预处理工艺的优化，采用Plackett- Burman 试验设计和均匀试验设计法，用数据处理软件对试验结果进行分析，筛选出了球磨预处理过程中的主要影响因素，得到了具有较好拟合度的回归方程；通过分析原料粒径，转速，原料填装量，研磨介质，交替时间等球磨条件对酶解效率的影响，得出行星式球磨机粉碎玉米秸秆的最佳工艺参数为：原料粒径0.5 mm，转速340 r/min，原料填装量3.4 g，装球量15个（Ф=10.0 mm），交替运行时间5 min。

The samples were heated to 1600℃ and kept for 20 min, some of them were water-quenched directly, and the others were furnace-cooled to a predetermined temperature and kept for 20 min and then quenched.

部分试样加热到1600℃保温20 min后直接淬火得到；其他试样1600℃保温20 min，炉冷到特定温度再保温20 min后淬火得到。

The optimum conditions for preparing CMS from walnut shell are: carbonization temperature 700—900℃, holding time 30min, heating rate 10℃/min; heat treatment (2nd carbonization) temperature 700—800℃, holding time 30min, heating rate 10℃/min; coal tar binder ratio 27—35wt%.

由核桃壳制炭分子筛的主要工艺条件为：一次炭化温度700—900℃，加热速率10℃／min，恒温时间30min；二次炭化温度700—800℃，加热速率10℃／min，恒温时间30min；粘结剂煤焦油配比27—35wt％。

Based on the technological theory of quick-cooked rice, by a series of variance trial and taste trials the paper gives the best technological conditions of quick-cooked rice soup ( cooking time 20 min., soak time 60 min, and soak temperature 45℃) and provides basic data for ist production on a large scale.

本文以速煮米生产工艺为指导，通过一系列正交试验和品尝试验，初步摸清了速煮粥生产工艺各个环节的最佳条件，为速煮粥大规模生产提供了基本数据。

Results indicated that for a pellet of 5 mm in diameter with carbon content of 5%, lime stone will be completely decomposed in about 3.4 min, and carbon burnt with 11.5 min elapsed of time, under ambient temperature of 1273K.

结果表明：对于粒径为5mm，含碳量为5%的料球，在1273K的环境温度下石灰石完全分解需要3.4分钟，焦碳完全燃烧需要11.5分钟。

RESULTS: Parturients did not differ regarding demographic data and initial pain score. Clonidine 150 microg , neostigmine 750 microg , and 75 microg clonidine plus 250 microg neostigmine produced ineffective and short-lasting effects. Clonidine 75 microg plus 500 microg neostigmine and 75 microg clonidine plus 750 microg neostigmine presented comparable durations of 90 +/- 32 and 108 +/- 38 min (mean +/- SD), respectively, and final analgesic efficacies, with 72.2% and 84%, respectively, of the parturients reporting a visual analog scale score of less than 30 out of 100 after 30 min.

结果显示，各组中的产妇在人口统计数据和初始疼痛评分方面没有差别。150μg可乐定、750μg新斯的明或75μg可乐定与250μg新斯的明联用并未产生止痛效果，或只有短期效果。75μg可乐定与500μg新斯的明联用以及75μg可乐定与750μg新斯的明联用产生的止痛效果持续时间相似，分别为90±32和108±38分钟；两种联用方案的最终止痛效力相似，分别有72.2%和84%的产妇在30分钟后视觉模拟量表评分低于30。

It was concluded that the optimized experiment conditions were coal particle size .074 mm, pulp density 10%, initial pH 2.5, cell inoculation amount 10%, microwave irradiation time 3 min, desulfurization cycle 4 d, temperature 30℃, rotation speed of rocking bed 160 r/min, the desulfurization rate of total sulfur reached 51.3%.

在煤样粒径为 200 目（＜0.074 mm）、煤浆浓度为 10％、初始 pH 为 2.5、菌体接种量为10%、微波辐照时间3 min、脱硫周期4 d、温度30℃、摇床转速为 160 r/min条件下，微波预处理和微生物联合作用对煤炭中全硫的脱除率可达51.3%。

Nowadays, most of research are to build a transmutative Petri Nets through adding controlling place sets, controlling arc sets and controlling policy to the basic Petri Nets, while the Controlled Petri Nets could be used to argue many controlling theory problems conveniently and to induce many logically and physically supervisory and solve the Event Feedback Controlling Problems and State Feedback Controlling Problem in DEDS supervisory theory.

目前大多数的研究表现为在变形后的受控Petri网基础上，利用各种方法求得各种逻辑型、结构型控制器，解决DEDS监控理论中的事件反馈控制问题与状态反馈控制问题。

On one hand, there are discussions with the works council and union about extension of short time working up to the end of September.

一方面，有讨论，工程理事会和联盟关于延长工作时间短至9月底。