查询词典 M.M.

Experiments of cylindrical gas cloud explosion were performed with 7.75 % of ethyne and 0.26 m3 of gas cloud volume and overpressures at 1.2 m and 1.6 m points from cloud center were recorded.

进行了乙炔浓度7.75%、气云体积0.26m3的圆柱形可燃气云爆炸实验，记录了距气云中心1.2 m与1.6 m两点的爆炸超压。

In the presence of 500nM TTX, 70%M/T cells presented spontaneous activity. 80%M/T cells with spontaneous activity appeared excitory postsynaptic currents , which could be reverted at 20mv, 14%M/T cells appeared inhibitory postsy-naptic currents , which the reverse potential was -90mv. Few presented both EPSCs and IPSCs.

当细胞外液有1uM的河豚毒，70%的M/T细胞有自发活动，其中80%自发活动是兴奋性突触后电流、它的反转电位是20mv.14%的自发活动是抑制性突触后电流，它的反转电位是-90mv，极少数细胞同时有EPSPs和IPSPs。

RESULTS: When the ratio of laser power to facular diameter was 2.7 kW/3 mm, the powder feeding speed was 90 r/min and the moving speed of numerical control machine was 5 mm/s, better H (826.61 μm) and W (3504.61 μm) were obtained.

结果： 在激光功率与光斑直径之比为2.7 kW/3 mm，送粉器转速为90 r/min和数控机床的运动速度为5 mm/s等参数下，TiZr粉末激光立体成形时具有较好的H和W，分别为826.61 μm和3504.61 μm。

RESULTS: When the ratio of laser power to facular diameter was 2.7 kW/3 mm, the powder feeding speed was 90 r/min and the moving speed of numerical control machine was 5 mm/s, H (826.61 μm) and W (3504.61 μm) were obtained.

结果： 在激光功率与光斑直径之比为2.7 kW/3 mm，送粉器转速为90 r/min和数控机床的运动速度为5 mm/s等参数下，TiZr粉末激光立体成形时具有较好的H和W，分别为826.61 μm和3504.61 μm。

RESULTS摘要: When the ratio of laser power to facular diameter was 2.7 kW/3 mm, the powder feeding speed was 90 r/min and the moving speed of numerical control machine was 5 mm/s, better H (826.61 μm) and W (3504.61 μm) were obtained.

结果摘要：在激光功率和光斑直径之比为2.7 kW/3 mm，送粉器转速为90 r/min和数控机床的运动速度为5 mm/s等参数下，TiZr粉末激光立体成形时具有较好的H和W，分别为826.61 μm和3504.61 μm。

The microstructure of Ti Zr alloy formed under this suitable technologic parameter matching was analyzed by scanning electron microscope. RESULTS: When the ratio of laser power to facular diameter was 2.7 kW/3 mm, the powder feeding speed was 90 r/min and the moving speed of numerical control machine was 5 mm/s, better H (826.61 μm) and W (3504.61 μm) were obtained.

结果： 在激光功率与光斑直径之比为2.7 kW/3 mm，送粉器转速为90 r/min和数控机床的运动速度为5 mm/s等参数下，Ti Zr粉末激光立体成形时具有较好的H和W，分别为826.61 μm和3504.61 μm。

Results Central foveal thickness and foveal thickness (mean thickness in the central 1000-μm diameter area) were 153±18 and 188±17μm, respectively.

结果 正常人黄斑中心小凹的视网膜最薄，平均厚度为(53±18)μm，直径1mm中心环视网膜下均厚度为(188±17)μm。

In the soil seed bank, the proportion of the worm-eaten seed was 53.79%. Compared with the seed rain, the quantities of the perfect and geminated seed were less 2.15 seeds m-2 and 0.20 seeds m-2 respectively.

土壤种子库中虫蛀种子占53.79%，与种子雨相比，完好种子和萌发种子数量分别减少2.15个 m-2和0.20个 m-2。

The horizontal and vertical first derivatives of magnetic anomalies of an infinite cylinder are calculated by the cosine transform method, in which the maximum errors are -028 nT/m and 047nT/m, respectively and the percent errors are generally within -357%～327% and -194%～188%, respectively except several data of the boundary and part are bigger because of remains of Gibbus effect. The calculating curve and theoretical curve are approximately coincident, and there is no influence by effective magnetic dip angle in computing.

利用余弦变换法计算的无限长水平圆柱体磁异常水平和垂向一阶导数的最大误差分别为-028 nT/m、047 nT/m；水平一阶导数的误差一般在-357%～327%之间，垂向一阶导数的误差一般在-194%～188%之间；计算的磁异常一阶导数值与理论值大致重合，而且不受有效磁化倾角的影响。

The light saturation point of sun leaves in canopy was 400 μmol photons m^(-2) s^(-1), and the maximum net photosynthetic rate was 4-6 μmol photons m^(-2) s^(-1). These data showed that C. hystrix saplings are sun plants.

结果表明：1刺栲冠层阳生叶的光饱和点为400 μmol photons m^(-2) s^(-1)，最大光合速率在4-6 μmol photons m^(-2) s^(-1)之间，说明刺栲幼树保持阳生植物的特征。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。