查询词典 Humboldt Current

This simulation takes into account of the plasma bootstrap current ,ion cyclotron resonance heating and fast wave current drive.

模拟中考虑了自举电流，并加入了离子回旋共振加热ICRH和快波电流驱动FWCD，得到了中心电子温度4。

It is possible to use a Darlington connection in place of the FET-bipolar combination in cases where the output current is high and the base current of the Darlington input would not cause a significant error.

本电路使用的 OP 必须对单位增益进行补偿。并且根据负载特性和输出级电路的特性可能需要额外的补偿。

Based on the current-rising-rate protection and current increment protection, the principle of DDL protection as well as its action equation is presented.

以电流上升率保护和电流增量保护为基础，提出了一种新型的DDL保护方法及整定原则，并推导出了完整的动作方程。

On the other hand, analyzed the mechanism of generating transformer inrush current and the characteristics and identification methods. Pointed out the existing problems that baseding on the principle of the dead angle of excitation inrush current identification method in transformer microcomputer protection.

另一方面分析了变压器励磁涌流产生机理及波形特点与识别方法，指出了在变压器微机保护中，基于中断角原理的励磁涌流识别方法及存在的题目。

Extracted the characteristics of excitation inrush current to establish a new identification method. This method has strong robustness for TA saturation, theoretical analysis and MATLAB simulation experiments indicated that the principle will not be affected by the TA saturation,*** and effective, and avoided the faults that hardware requirements of high and computation in the method of traditional accurate measuring the dead angle of excitation inrush current.

提取励磁涌流的特征量，并以此建立识别励磁涌流的新方法，该方法对TA饱和具有很强的鲁棒性，理论分析和MATLAB仿真试验均表明该原理不受TA饱和的影响，简单有效，避免了传统精确丈量励磁涌流中断角的方法对硬件要求高及运算量大的缺点。

The air conditioner forced draft fan ventilates the way to have longitudinal and the crosswise two kinds generally, the lateral ventilation the air current overflow sectional area is big, the wind speed is small, easy to create the big area the dead angle, but longitudinal ventilates the air current the overflow sectional area to be small, the wind speed is big, the dead angle area is very small.

冷风机通风方式一般有纵向和横向二种，横向通风的气流过流断面积大、风速小，容易造成较大面积的死角，而纵向通风气流的过流断面积小，风速大，死角面积很小。在使用条件许可的情况下，应该尽可能采用先进的纵向通风方式。

From the junction temperature-varied optical properties measurement, we find that the luminous efficiency will decay more quickly at low current operation. However, when the current density increases to the saturation capacity of the quantum well, the decay ratio will reach a constant.

在变温的光学特性量测上，由实验结果发现，发光效率在较低电流时会衰减的较快，然而在注入电流达到量子井的饱和量后，其发光效率随接面温度升高衰减的现象则会趋近於固定的比例。

More than 50 GaAs/GaAlAs High Power Single Quantum Well Semiconductor Lasers are aged. The threshold current decreases during the early aging (first 520 h) and the largest decrease is 57 mA. From the aging result of more than 1000 h at constant current, we find that output power increases during the early aging , and then decay slowly according to exponent law.

通过对50余只808nm的GaAs/GaAlAs高功率单量子阱远结半导体激光器的老化实验观测，在老化初期（前520h），阈值电流随老化时间的延长而下降，下降幅度高达57mA，从1000h多的恒流电老化结果可以看出，器件的输出光功率在老化初期有所上升，随后，表现出按指数规律缓慢下降的行为。

The current decouple control of direct current control strategy is selected as the control way.

确定了直接电流控制中的电流解耦控制作为本课题的控制方案。

This paper presented the research and exploration of mechanism and technics as well as the design of the magnetic circuit of this new compound machining, based on above, establishing the parameter model, meantime, analyzing influential effects on productivity of magnetic and EDM compound machining the holes through large numbers of experiments, including velcoity contrast experiments of pre-compound and after-compound machining with the change of current, velcoity contrast experiments of pre-compound and after-compound machining with the change of magnetic induction, velcoity contrast experiments of pre-compound and after-compound machining with the change of impulse width, experiments of the superficial roughness, experiments of the Electrode wastage, and intersectant experiments analysis as well as the change experiments of current waveforms. Through a number of experiments we analysed the influential effects of magnetic and EDM compound machining, compared the factors with EDM by oneself. A large of experiment records and deducibility have demonstrated that the productivity of magnetic and EDM compound machining is developed by 20%～400% than traditional EDM.

本论文对磁场电火花复合加工这种新的复合加工的机理、工艺和复合加工的磁路设计进行了研究和探索，在此基础上，建立了磁场电火花复合加工的参数模型，同时通过大量的随着电流变化磁场电火花复合前后加工速度对比实验、磁感应强度变化时的加工速度变化实验、随脉冲宽度变化的加工速度实验、表面粗糙度实验、电极损耗量实验、磁场电火花复合加工正交实验分析、电流波形变化等实验，实验分析了影响磁场电火花小孔加工效率的因素，并且跟单一的电火花加工中的影响因数进行了比较，大量的实验数据和理论推导证明磁场电火花复合加工比传统的单一电火花加工的效率提高了20％～400％左右。

More direct, directer ; most direct, directest

径直的，笔直的

Do you know how to use a chain saw?

你知道如何使用链锯吗？