查询词典 Hull

Here, you can see various angles of both the top and bottom hull halves.

在这里，您可以看到不同的角度都顶部和底部的船体部分。

I really hard cheese,I was sliped because I steped on hull of banana.

我真倒霉，踩在香蕉皮上滑倒了。

Depending on how this works for me, I've been kicking around the idea of possibly doing a hardback for the hull.

就如何根据本工程对我来说，我已经踢左右的想法，可能做了精装，为船体。

You of havings variety I clear, I seem to be so in your in front inhospitality but doesn't matter, that be that the mollusk be weak weak of hull.

你的所有变化我都明了，我在你面前显得那么冷漠而无所谓，那是软体动物单薄脆弱的壳。

Lower the anchor and lift it up to the hawse pipe separately for P and S side, check the contact condition of anchor fluke and hull.

将锚放低，然后分别将锚拉到左舷和右舷锚链管，检查锚爪与船体贴合情况。

Rubberand drum at maximum force at A point of RADIUS R1 and minimum mechanical Department b. RADIUS R2 is different, rubber roller compression over C forms the convex hull, the radius of the highlast C is R3, point b is the radius of the lining of the RADIUS rubberand drum after three RADIUS R1 with the size of the change of Center distance drum to determine the ideal pressure: 0.5mm by Feller gauge or flattening of galvanized wire to precise tuning of two drums of hobber pillow gap, so that it is up to the required data.

橡皮滚筒在最大受力处A不面的半径R1和最小受力处B不面的半径R2是差别的，橡皮滚筒受不抬后转动在C处变成凹包，凹包最矮不面C的半径是R3，B不面的半径是包衬后的橡皮滚筒半径不一个半径的巨细的R1 用保留滚筒洋心距来猜测抱负不张力：用塞尺或0.5mm的铅丝不抬扁来大略不天调动二滚筒的滚枕间隙，使之符分规矩的数据。

Figure 2 printing plate gaskets is higher than the 0.2 ~ 0.3mm hobber pillow, blanket below the occipital hobber 0.05mm, a2, B2 Department produces a smaller convex hull, of course, less friction and sliding, wear plates, no szlama and "" taping, fault-printing plates and high, less hierarchical dot gain, clearly, the life expectancy of the machine, the electrical power consumed less.

图2印版的衬垫矮于滚枕0.2～0.3mm，橡皮布矮于滚枕0.05mm，在A2、B2处爆发的凹包较小，当然摩擦和滑动也多，印版磨损较多，无不推不净和"杠子"障碍爆发，印版的耐印率矮、网不面放大多，条理纯楚，机械的寿命放大，电机耗电也多。

As you can see, I ve manufactured two stands to hold the hull in a level position as well.

你可以看到，我已经制造两个站举行的船体在一个水平立场。

The hot line that profiled bar factory is Lai steel Inc. produces one of units, have small-sized, medium-sized and large 3 section product line, basically produce product of profiled bar of etc of light-duty series, medium-sized series and profiled bar of large series H, main body equipment is advanced, year productivity 2.4 million tons of above. 2004, h profiled bar passed product certification of Chinese ship's classification society, the mark is worn the pass that profiled bar of Lai steel H had hull to use steel and marine oil platform to use steel. 2006, passed day bid and Europe mark attestation respectively, hold one's head high push forward Japan and Europe.

梗概： 型钢厂是莱钢股份有限公司的热线生产单位之一，拥有小型、中型和大型三条型钢生产线，主要生产轻型系列、中型系列和大型系列H型钢及其他型钢产品，主体设备先进，年生产能力240万吨以上。2004年，H型钢通过了中国船级社产品认证，标志着莱钢H型钢拥有了船体用钢和海洋石油平台用钢的通行证。2006年，分别通过了日标和欧标认证，昂首挺进日本和欧洲。

This will be our plane that we are going to pick the hull points from...

这将是我们的飞机，我们将挑选船体点。。。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。