查询词典 CAM

So,our victim was using a dangerous insecticide .- Not unusual for someone who's a couple of tacos short of a combo plate.

这里说死者在使用一种有毒危害的杀虫剂，Cam说这也算不得蹊跷，因为如果生活水平本就不高、缺衣少食的话，自然不会不关心到这个层面。

In shoe last machining, relative motion data is constantly adjusted to avoid interference occurrence.

最后本文介绍了鞋楦CAD/CAM系统软件的设计框架和部份操作界面。

Under this discrete model, the whole system data are standardized and make it easier and possible to realize many shoe last CAD/CAM techniques.

在介绍了鞋楦数据的二维、三维变换方法后，为实现后续算法灵活、方便以及在保证精度的前提下尽可能简化算法。

The paper introduced the general scheme,the process plan and some key technics of NC trnsfer line for several kinds of cylinder head cam shaft cover s manufacture of car engine,some important parts were discussed in detail.

介绍了轿车发动机缸盖凸轮轴轴承盖多品种加工数控组合机床自动线的总体布局、工艺方案以及线上采用的关键技术，并对部分重要部件作了较详细的叙述。

A trigger tab (104) engages the trigger arm when the seat is returned from the forwardly extended position to the full rearward position to release the cam plate to the non-actuated position and allow the locking mechanism to return to the locked position interlocking the upper and lower tracks and preventin g further sliding movement therebetween.

当座椅组件从前伸位置返回到最靠后位置时，一个触发片(104)与触发臂接合，从而将凸轮盘松开并使之回到非致动位置，并且使锁止机构回到联锁上下滑轨并阻止两者间的进一步滑动的闭锁位置。

Movement Analysis of Different Screw-pitch Axial Sliders Cam Differential

说明：补充资料仅用于学习参考，请勿用于其它任何用途。

A new TMJ exerciser was designed and produced using computer aided design/computer aided manufacture program. Screw-driven technique was used for opening the spatula. The device was tested in clinical setting. The design was revised, re-produced, and re-tested based on patients' report and clinical evaluation.

此运动器需经检测及临床试用，并在使用方便、易於携带、耐用程度高及力量易控制等原则下进行重复机构设计及摸拟分析，经由CAD/CAM连结切削并进行细部加工成型，以完成产品之制造。

The general approach is "" backers again correction on adjusting screw, making roller cam minimum surface between 0.03 ~ 0.05mm of clearance.

凡是的办理办法是从头订正&背景&上的调度螺丝，使滚子在凸轮的最小背时两者保留0.03~0.05mm的间隙。

The contact-point pressure must be within specifications, since low point pressure will allow the points to Bounce and Burn, and high pressure will cause rapid wear of the points, cam, and rubbing Block.

接触压力计：触点压力必须符合技术要求，因为触点压力低会使触点产生跳振和烧毁触点压力高会加快触点凸轮和顶块的磨损。

Therefore, you must release the take the wheel and loosen its teeth in its teeth on the shaft by time cam control rocker, but equipped page machine in its wheel is compact, inconvenient demolition, and pick out the teeth and inspection of pressure on the relative position of the key is to detect many parts of the machinery in a manner worthy, opening the restore time, the earliest possible time to 2300 hours, easily affecting production.

因此必须松开叼纸轮的定位，并且松开叼牙轴上受叼牙时间凸轮控制的摆杆，但由于配页机的叼纸轮安装较紧凑，不方便拆卸，且叼牙与检测压力相对位置是检测多帖关键的机械部位，拆开后，还原时间长，最快也要二三个小时，容易影响生产。

Breath, muscle contraction of the buttocks; arch body, as far as possible to hold his head, right leg straight towards the ceiling (peg-leg knee in order to avoid muscle tension).

呼气，收缩臀部肌肉；拱起身体，尽量抬起头来，右腿伸直朝向天花板（膝微屈，以避免肌肉紧张）。

The cost of moving grain food products was unchanged from May, but year over year are up 8%.

粮食产品的运输费用与5月份相比没有变化，但却比去年同期高8％。