查询词典 CAM

The truth of the measuring method is established by precision and feasibility analysis.The restriction of using this method to measure surfaces of roller gear cam is discussed, and the next research direction is confirmed.

分析了这种弧面分度凸轮测量方法的局限性，即该方法只适于对已知参数的弧面分度凸轮进行精度检验；如果要测量参数未知的凸轮，反求参数，这种方法是不适用的；针对该方法的局限性确定了下一步的研究方向。

The clearance cause more serious effect on the response of turret than that of the rotary table. This result agrees with the experimental response of roller gear indexing cam mechanism. In addition, some problems, such as the impacts on mechanism with clearance, effect on response for preload, effect for inertia of rotary table and stiffness of output-shaft, effect on wave of velocity and torsion for motor characteristic, and so on are investigated.

通过对扭转动力学模型的计算还对以下问题进行了研究：间隙造成的横越冲击的表现；预紧的存在对响应的影响；间隙的存在对有廓形误差的凸轮机构的动力学响应的影响；分度盘轴的刚度和载荷盘惯量对含间隙分度凸轮机构响应的影响；电机特性对转速波动和扭矩波动的影响等等。

Rothbart # Format:PDF 5.13MB # Page Count: 606 pages # Publisher: McGraw-Hill Professional; 1 edition (October 23, 2003)# Language: English # ISBN-10: 0071377573 # ISBN-13: 978-0071377577 The cam, used to translate rotary motion into linear motion, is an integral part of many classes of machines, such as printing presses, textile machinery, gear-cutting machines, and screw machines.

该文研究基于internet的异地企业间进行自动车床凸轮组协同开发的过程，介绍了协同设计系统的基本框架与实现方法，并应用计算机网络技术及机械CAD技术，开发了一个可以实现自动车床凸轮组设计的远程协同设计系统。

In the amplifying design of the Guanghua offset printing machine PZ1740, the software has been applied to the design of the cam mechanisms for the rotary sheet transfer, grippers on-off and pressure on-off etc, and the desired results has been achieved for.

系统总结了印刷机械中凸轮机构的反求设计理论，研制了相应的计算机辅助设计软件，在光华胶印机PZ1740的放大设计中，应用于圆递纸机构、开闭牙机构和离合压机构等的凸轮机构的设计，取得了预期的设计效果，从而验证了理论的正确性和软件的实用性。

Swayig begnawing unleashmy paper paper teeth in, call the static state, to ensure the accuracy of the paper begnawing, still are counting on "" on adjusting screw to control, when swayig begnawing paper teeth rockers "" rock the block and if connecting rod in hand on the cam roller should be the minimum surface, gap 0.03 ~ 0.05mm, if less than 0.03mm or no gap is at rest time is too short or simply not still be in an inconsistent state, more likely to result in bilateral irregular misregister.

摆动咬纸牙在咬纸时，答在遨游状况下举行，以包管咬纸的不确性，遨游工夫是由&背景&上的调度螺丝来把持的，当摆动咬纸牙摆杆块与&背景&隔绝时，连杆牵手上的滚子答处于凸轮的最小背，间隙为0.03~0.05mm，如果小于0.03mm或底子操纵间隙不离表明遨游工夫太不幼或底子不离操纵遨游工夫，不兵处于不稳不退状况，较便当变成双边无法规套印禁绝的障碍。

The lift of the heddles can be achieved by using cam or dobby operated harnesses and each has its own limitations.

可以采用凸轮或多臂来控制综框的升降，但这两种方式都有自身的局限性。

The corporation possesses not only the technology of production moulds for all kinds of iceboxes and refrigerators, but also the ability of producing single-station vacuum forming machines (We have successfully produced and tested 2 single-station vacuum forming machines).

为适应冰箱模具行业日趋完善的技术要求，公司先后从台湾和捷克引进了两台数控加工中心，传统意义上加工已大部分由CAM完成。

During the process of camshaft measurement, the phase datum of the key pin or the locating pin can be determined precisely by using the minimum error method of curve symmetry and the cam nose position can be determined by using the minimum error method near the" sensitive point".

在凸轮测量中，采用曲线对称最小误差法，可精确确定键销或定位销的相位基准；采用&敏感点&附近最小误差法，可精确确定凸轮&桃尖&位置。

Established in 1997,JINTAI is specialized in the drawer lock, cam lock, knob lock, mailbox lock and

金泰公司成立于1997年，是一家专业设计并制造高安全性，高品质琐具的企业，主要生产抽屉锁，转舌锁，按钮锁，邮箱锁等。

All design process of two microwave ovens products were finished considering of the individuality fashion of the electrical appliances product design by using large-type CAD/CAM software system UG.

而消费市场对具备个人色彩产品的需求逐渐增加，也是助长此趋势的主要原因；另外，新技术与新材料的运用也使得产品设计的领域更为宽广。

In the negative and interrogative forms, of course, this is identical to the non-emphatic forms.

。但是，在否定句或疑问句里，这种带有"do"的方法表达的效果却没有什么强调的意思。

Go down on one's knees;kneel down

屈膝跪下。。。下跪祈祷