英语人>网络例句>AL 相关的网络例句
AL相关的网络例句
与 AL 相关的网络例句 [注:此内容来源于网络,仅供参考]

The synthesis mechanism of Al_(13)in the process of electrolysis was discussed,the effects of electrolysis voltage,the original concentration of Al~(3+),the circulation mixing rate of the electrolyte and the exchanging frequency of the electrodes on the synthesis velocity of Al_(13),ratio of Al_(13)in total Aland the electrolysis time were studied.

本工作对电解过程中Al_(13)的形成机理进行了探讨,并研究了电解电压、Al~(3+)的初始浓度、电解液的循环搅拌速度和阴阳电极的互换频率对Al_(13)的合成速度、Al_(13)占总铝的比率及电解所需时间的影响,得出了电解法制备Al_(13)的最佳工艺条件:电极互换频率为1次·min~(-1)、电解液中Al~(3+)的初始浓度为0.5000mol·L~(-1)、电解电压为12V和0.5L·min~(-1)的电解液循环搅拌速度,在此条件下电解125min可制得碱化度为82.0%,Al_(13)占总铝的比率达91.2%的液体产品。

When the pouring temperature is close to the liquidus temperature of AlSi7Mgalloy, the primary α-Alin the billets of AlSi7Mg alloy solidifies into spherical or nodular grainswhich are small and distributed homogeneously. In order to obtain non-dendritic semi-solidbillets,the appropriate pouring temperature is 615℃. The faster cooling rate,the melt flowing and largersolidification region induced by the near liquidus pouring temperature promotes theformation of spherical or nodular primary α-Al.

实验表明:当浇注温度接近液相线温度时,AlSi7Mg合金中的初生α-Al凝固成球状或粒状,晶粒细小,分布均匀;获得球状或粒状AlSi7Mg合金半固态坯料的最佳浇注温度为615℃;在接近液相线温度下浇注,较快的合金熔体冷却速度、浇注引起的合金熔体活动和大范围的同时凝固促使AlSi7Mg合金形成球状或粒状的初生α-Al组织。

A reparing material for reparing the coke oven by spraying the semi-dried it is prepared from the raw Al-Si material chosen from mullite, high-Al alumine, etc.

焦炉修补用半干法喷补料,其组分及组分重量百分比为:铝硅质原料55~78%、结合剂10~25%、烧结剂和可塑剂3~5%、膨胀剂3~7%、Al 2 O 3 微粉或/和SiO 2 微粉5~10%;外加剂加入量为总量的0.1~1.0%。

The main results and conclusions are as follows:The trans-1,4 content of polybutadiene increased from 50%to 89%along with the increasing of Al/Li ratio;the trans-1,4 content of polyisoprene increased from 24%to 46%as well as 3,4 content along with the increasing of Al/Li ratio;the microstructure of polystyrene was invariable and atactic.

主要研究结果及结论如下:随着Al/Li的增加,聚丁二烯的反式结构含量从50%增加到89%;聚异戊二烯的反式-1,4-结构含量从24%增加到46%,并且其3,4结构含量也有所增加;聚苯乙烯的微观结构基本没有变化,为无规聚苯乙烯。

The main results and conclusions are as follows:The trans-1,4 content of polybutadiene increased from 50%to 89%along with the increasing of Al/Li ratio;the trans-1,4 content of polyisoprene increased from 24%to 46%as well as 3,4 content along with the increasing of Al/Li ratio;the microstructure of polystyrene was invariable and atactic.

加热器主要研究结果及结论如下:随着Al/L i的增加,聚丁二烯的反式结构含量从50%增加到89%;聚异戊二烯的反式-1,4-结构含量从24%增加到46%,并且其3,4结构含量也有所增加;聚苯乙烯的微观结构基本没有变化,为无规聚苯乙烯。

In the low-temperature case, a well-defined critical thickness of 4 ML, at which atomically flat Al films form, is identified.

我们认为这可能是界面的弹性能和Al(100)和Al(111)表面自由能共同作用的结果。

The framework Al atom was located in the channel intersection when TPA salt and 1, 6-hexanediamine was used as templates whereas the Al atoms can located both in the channels and channel intersections with butylamine or ethylenediamine as template.

当以TPA季铵盐和己二胺为模板剂时,骨架Al原子处于分子筛孔道交叉位置上,证实了文献中关于ZSM-5的酸中心处于孔道交叉处的说法。

Analytical results show that: Anode evaporation rate, which determines mostly the production rate of UFMP, is influenced by the many factors including electric parameters of arc, ambient conditions and material properties et al; Existence and increase of anode ejection can influence the production rate and property of UFMP; It is firstly found and investigated that surface connexity phenomenon of Al anode material. Analyses and calculation show that formation of anode spot and existence of self-magnetic field force play an important part in surface connexity process; Effects of cathode material on prepared UFMP is also experimentally studied and theoretically analysed. It shows that effect of the cathode is inconsiderable under the experimental conditions used in the study. At last, the experimental results found in part one are analysed and discussed in detail.

然后详细分析了电弧与电极间的相互作用过程,结果表明:决定超微粉产率的阳极材料蒸发率受许多因素影响,它主要与电弧电参量,环境条件及材料性质有关;阳极表面液滴喷溅的存在和加剧将严重地影响所制超微粉的产率和性质;首次发现和实验研究了Al阳极表面凸起现象,并对此现象进行了详细的理论分析和实际估算,认为阳极斑点的形成及自磁场作用力的存在在该过程中起着重用作用;实验研究和理论分析了阴极材料对所制超微粉的影响,认为在本文所用实验方法及条件下,阴极材料对粉的影响很小。

The results show that the effect of addition or no-addition of degasser on grain refinement of Al-5.0%Si alloy ingot is...

结果表明,除气剂的添加与否对Al-5%Si合金铸锭组织的细化没有影响,铸锭由粗大的柱状晶组织构成;采用合适的超声波处理时间,Al-5%Si合金铸锭的等轴晶获得率大幅度提高,可使整个铸锭组织变为细化的等轴晶组织;超声波振动时间过长将导致铸锭内气孔的增加;根据克劳修斯-克拉柏龙方程,某一强度的超声波引起的压力冲击波作用,导致液相转变为固相,引起了超声波的细晶作用。

The measured dynamitic solidification curve shows that the mushy zone become wider with the increase of Al amount and fluidity decreases as the well developed dendrites hinder the flow of the liquid alloy.

合金的液相线温度随Al量的增加而降低,Al含量从24%增至35%时,其过热度约增加1倍。

第19/100页 首页 < ... 15 16 17 18 19 20 21 22 23 ... > 尾页
相关中文对照歌词
Al Andar (Move On - in Spanish)
Crei Morir E Ir Al Cielo
Al Ritmo De La Lluvia
Al Final De Cuentas
Duelo Al Amanecer
Vente Al Mas Alla
Se Me Olvidó Todo Al Verte
El Alma Al Aire
Al Olvido Invito Yo
Al Pan, Pan Y Al Vino
推荐网络例句

I didn't watch TV last night, because it .

昨晚我没有看电视,因为电视机坏了。

Since this year, in a lot of villages of Beijing, TV of elevator liquid crystal was removed.

今年以来,在北京的很多小区里,电梯液晶电视被撤了下来。

I'm running my simile to an extreme.

我比喻得过头了。