高强度热处理

基本解释 (translations)

maraging

与高强度热处理相关的网络例句 [注：此内容来源于网络，仅供参考]

The results show that proper RRA heat treatment can improve SCC properties with retention of the high strength of T6 level. After preaging at 100℃for 24 h, retrogression at 200℃for 7 min, and reaging at 100℃for 24 h, the ultimate tensile strength, yield strength and elongation of the alloy are 795 MPa, 767 MPa and 9.1%, respectively. Meanwhile the failure time of the alloy applied to tensile strength of 210MPa in 3.0%NaCl+0.5%H2O2corrosion condition is longer than 720 h. The corresponding TEM observation shows that after retrogression for 7 min and re-aging treatment, the microstructure of grain boundary is similar to that treated in the T73 condition with coarsen and isolated distribution, and the microstructure inside grain is similar to that treated in the T6 condition with small and homogeneous distribution.

研究结果表明：在峰值时效T6状态下合金强度高，但抗应力腐蚀性能差；采用合适的RRA热处理工艺既能使合金保持T6状态下的高强度的同时，又能显著改善合金的抗应力腐蚀性能；经回归7 min RRA处理后合金的晶界类似T73态析出相聚集粗化，而晶内类似T6态析出相细小弥散分布，在拉伸应力为210 MPa和3.0%NaCl+0.5%H2O2腐蚀液中，其断裂时间大于720 h，相应的抗拉强度、屈服强度和延伸率分别为795 MPa， 767 MPa和9.1%，显示优越的综合性能。

The results show that proper RRA heat treatment can improve SCC properties with retention of the high strength of T6 level. After pre-aging at 100 ℃ for 24 h, retrogression at 200 ℃ for 7 min, and reaging at 100 ℃ for 24 h, the ultimate tensile strength, yield strength and elongation of the alloy are 795 MPa, 767 MPa and 9.1%, respectively. Meanwhile the failure time of the alloy applied to tensile strength of 210 MPa in 3.0%NaCl+0.5%H2O2 corrosion condition is longer than 720 h. The corresponding TEM observation shows that after retrogression for 7 min and re-aging treatment, the microstructure of grain boundary is similar to that treated in the T73 condition with coarsen and isolated distribution, and the microstructure inside grain is similar to that treated in the T6 condition with small and homogeneous distribution.

研究结果表明：在峰值时效T6状态下合金强度高，但抗应力腐蚀性能差；采用合适的RRA热处理工艺既能使合金保持T6状态下的高强度的同时，又能显著改善合金的抗应力腐蚀性能；经回归7 min RRA处理后合金的晶界类似T73态析出相聚集粗化，而晶内类似T6态析出相细小弥散分布，在拉伸应力为210 MPa和3.0%NaCl+0.5%H2O2腐蚀液中，其断裂时间大于720 h，相应的抗拉强度、屈服强度和延伸率分别为795 MPa， 767 MPa和9.1%，显示优越的综合性能。

The results show that proper RRA heat treatment can improve SCC properties with retention of the high strength of T6 level. After pre-aging at 100℃ for 24 h, retrogression at 200℃ for 7 min, and reaging at 100℃ for 24 h, the ultimate tensile strength, yield strength and elongation of the alloy are 795 MPa, 767 MPa and 9.1%, respectively. Meanwhile the failure time of the alloy applied to tensile strength of 210 MPa in 3.0%NaCl+0.5% H2O2 corrosion condition is longer than 720 h. The corresponding TEM observation shows that after retrogression for 7 min and re-aging treatment, the micro- structure of grain boundary is similar to that treated in the T73 condition with coarsen and isolated distribution, and the microstructure inside grain is similar to that treated in the T6 condition with small and homogeneous distribution.

研究结果表明：在峰值时效T6状态下合金强度高，但抗应力腐蚀性能差；采用合适的RRA热处理工艺既能使合金保持T6状态下的高强度的同时，又能显著改善合金的抗应力腐蚀性能；经回归7min RRA处理后合金的晶界类似T73态析出相聚集粗化，而晶内类似T6态析出相细小弥散分布，在拉伸应力为210 MPa和3.0%NaCl+0.5%H2O2腐蚀液中，其断裂时间大于720h，相应的抗拉强度、屈服强度和延伸率分别为795 MPa，767 MPa和9.1%，显示优越的综合性能。

Main applicability: Welding of the miamond knife head, the carbide alloy saw bit , machine work use carbide alloy cutter welding, if the cutting tool welding such as miamond cutter , drilling tool , lathe tool , shaper tool , milling cutter , broach; Standard piece , hot bolt rammer, if high-strength bolt , nut etc.; Hardware implement , handwork implement heat treatment, if tongs , spanner , whorl utensil , hammer , axe; The accessory high frequency quenching sells the various automobile accessory , motorcycle at reduced prices, such as: Crank shaft , connecting rod , wrist pin , crank pin , sprocket , axial cam , air valve , various rocker arm , rockshaft; Within speed change box, the various gear wheel , castellated shaft , biography prop up high frequency quenching treatment such as half axes , various small axis , various shift fork; The part heat treatment , the high frequency quenching that the gear wheel , sprocket , various axis , castellated shaft , pin wait for if various handle metal; Mssingle of face slide way quenching sells machine tool industry machine at reduced prices waiting.

主要适用范围：金刚石刀头的焊接，硬质合金锯片、机械加工用硬质合金刀具的焊接，如金刚石刀具、钻具、车刀、刨刀、铣刀、铰刀等刃具的焊接；标准件、螺栓的热镦，如高强度螺栓、螺帽等；五金工具、手工工具的热处理，如钳子、扳手、旋具、锤子、斧头；各种汽车配件、摩托车配件的高频淬火处理，如：曲轴、连杆、活塞销、曲柄销、链轮、凸轮轴、气门、各种摇臂、摇臂轴；变速箱内各种齿轮、花键轴、传支半轴、各种小轴、各种拨叉等高频淬火的处理；金属零件的热处理，如各种齿轮、链轮、各种轴、花键轴、销等的高频淬火处理；机床行业的机床床面导轨的淬火处理等。

Main and slave rails are chose with high strength material. Its top and sides are all manufactured in very good surface. The precise rack is at main rail.

导轨采用高强度热处理加工路轨制作，导轨的顶面和侧面都经过精密机械磨削加工，在导轨外侧面装置精密齿条。

The strength of HSLA steel with ferritic plus pearlitic mierostruetures has attained the limited value of 450～500MPa by traditionally microalloying treatment and TMCP. In order to further improve the strength grade, low carbon bainitic steel plates should be developed.

通过采用形变热处理工艺和微合金化，在保证高韧性和优异的焊接性能的条件下，具有铁素体珠光体组织的低碳低合金高强度钢的屈服强度可以达到500～550MPa的极限水平。

The influence of the methyl modified SiO 2 gel glass matrices on the thermal and fluorescence properties of photoactive organic species were also studied in t...

结果表明，由于甲基的影响，缩聚反应速度成为以纯 MTES为先驱物制备光学均匀复合固态染料激光介质的关键控制因素，甲基改性复合固态染料激光介质可进行较高温度热处理，经适当温度热处理后，染料的荧光强度有较大提高。

Based on these problems, this article provides a new solution of applying the boriding ——heat treatment of compound technology of austempering, it makes the face of the mold have the characteristics of high rigidity, strong wear proof and good tenacity, thus makes the li.

针对以上问题，本文采用了渗硼-等温淬火复合强化热处理工艺，使冷镦凹模具有了表面高硬度、高耐磨性与基体具有高强度、高韧性的完美结合，故可使模具使用寿命比常规热处理工艺提高20倍以上。

The main scope of application: Diamond Cutter welding, carbide saw blades, machining with carbide tools of welding, such as diamond tools, drill, tools, planing, milling cutter, reamer, such as welding and cutting tools; standard parts , bolts of hot upsetting, such as high strength bolts, nuts, etc.; hardware tools, hand tools, heat treatment, such as pliers, wrenches, rotary tools, hammers, axes; all kinds of automobile fittings, motorcycle fittings of high-frequency quenching treatment, such as : crankshaft, connecting rod, piston pin, crank pin, sprocket, camshaft, valves, all kinds of rocker arm, rocker shaft; gearbox various gears, spline shaft, axle bronchitis, all kinds of small shafts, high-frequency quenching, such as various fork of the handle; metal parts of the heat treatment, such as a variety of gears, chain wheel, the wheels, vibrating screen, a variety of shaft, spline shaft, and marketing of high-frequency quenching treatment, etc.; machine tool machine tool industry bed rail, such as the quenching treatment.

主要适用范围：金刚石刀头的焊接，硬质合金锯片、机械加工用硬质合金刀具的焊接，如金刚石刀具、钻具、车刀、刨刀、铣刀、铰刀等刃具的焊接；标准件、螺栓的热镦，如高强度螺栓、螺帽等；五金工具、手工工具的热处理，如钳子、扳手、旋具、锤子、斧头；各种汽车配件、摩托车配件的高频淬火处理，如：曲轴、连杆、活塞销、曲柄销、链轮、凸轮轴、气门、各种摇臂、摇臂轴；变速箱内各种齿轮、花键轴、传支半轴、各种小轴、各种拨叉等高频淬火的处理；金属零件的热处理，如各种齿轮、链轮、行车轮、振动筛、各种轴、花键轴、销等的高频淬火处理；机床行业的机床床面导轨的淬火处理等。

The main scope of application: Diamond Cutter welding, carbide saw blades, machining with carbide tools of welding, such as diamond tools, drill, tools, planing, milling cutter, reamer, such as welding and cutting tools; standard parts , bolts of hot upsetting, such as high strength bolts, nuts, etc.; Hardware tools, hand tools, heat treatment, such as pliers, wrenches, rotary tools, hammers, axes; a variety of auto parts, motorcycle accessories, high-frequency quenching treatment, such as : crankshaft, connecting rod, piston pin, crank pin, sprocket, camshaft, valves, all kinds of rocker arm, rocker shaft; gearbox various gears, spline shaft, axle bronchitis, all kinds of small shafts, high-frequency quenching, such as various fork of the handle; metal parts heat treatment, such as a variety of gears, sprocket, all kinds of shaft, spline shaft, and marketing of high-frequency quenching treatment, etc.; machine tool industry machine bed rails of Quenching disposal.

主要适用范围：金刚石刀头的焊接，硬质合金锯片、机械加工用硬质合金刀具的焊接，如金刚石刀具、钻具、车刀、刨刀、铣刀、铰刀等刃具的焊接；标准件、螺栓的热镦，如高强度螺栓、螺帽等；五金工具、手工工具的热处理，如钳子、扳手、旋具、锤子、斧头；各种汽车配件、摩托车配件的高频淬火处理，如：曲轴、连杆、活塞销、曲柄销、链轮、凸轮轴、气门、各种摇臂、摇臂轴；变速箱内各种齿轮、花键轴、传支半轴、各种小轴、各种拨叉等高频淬火的处理；金属零件的热处理，如各种齿轮、链轮、各种轴、花键轴、销等的高频淬火处理；机床行业的机床床面导轨的淬火处理等。

与高强度热处理相关的网络解释 [注：此内容来源于网络，仅供参考]

martrix alloy：马特里斯合金

marging steel 马式体高强度热处理钢 | martrix alloy 马特里斯合金 | meehanite cast iron 米汉纳铸钢

martrix alloy：马特里斯合金钢

marging steel 马式体高强度热处理钢 | martrix alloy 马特里斯合金钢 | meehanite cast iron 米汉纳铸钢

Casting,steel：低锰铸钢

low alloy tool steel 特殊工具钢 low manganese | casting steel 低锰铸钢 | marging steel 马式体高强度热处理钢 martrix

maral：马拉赤鹿

maraging 高强度热处理 | maral 马拉赤鹿 | maranticmarasmaticwasting 消耗的

plumbate：高铅酸盐

高气压圈anticyclone | 高铅酸盐plumbate | 高强度热处理maraging

maraging：高强度热处理

Mar. 三月 | maraging 高强度热处理 | marahuite 土状沥青褐煤

maraging：马氏体时效处理

maracaibo 马拉开波 | maraging 马氏体时效处理 | maraging 高强度热处理

maraging：马氏体时效处理 高强度热处理

mar-aging改变钢的马丁体结构法 | maraging马氏体时效处理 高强度热处理 | maragingsteel马氏体时效钢

Maraging Steel：马式体高强度热处理钢

low alloy tool steel 特殊工具钢 | maraging steel 马式体高强度热处理钢 | mateix alloy 马特里斯合金

Maraging Steel：马式体高强度热处理钢,马氏体时效钢

maraging || 马氏体时效 | maraging steel || 马式体高强度热处理钢,马氏体时效钢 | marble || 大理石,大理岩,石弹,玻璃球