顶高

词组短语

jack-up

与顶高相关的网络例句 [注：此内容来源于网络，仅供参考]

Pitch circle diameter: d = mz = 3X12 = 36 Tooth crown heights: ha = m (f0 + x)= 3X (l +0.5)= 4.5 Tooth High: hf = m (f0 + cx)= 3X (l +0.25-0.5)= 2.25 Tooth full height: h = ha + hf = 4.5 +2.25 = 6.75 Addendum circle Chemical pumps diameter: Da = d +2 ha = 36 +2 X4.5 = 45 Fixed string tooth thickness: Sxn = m (π/ 2 * cos2a + xsin2a)= 3X (1.387 +0.6428 X0.5)= 5.125 Fixed string of high gear tooth thickness measurement: hxn = m (π/ 8 * sin2a + xsin2a)= 3X (0.7476X0.117X0.5)= 2.42 Modulus coefficient x0.5 m3 O20 ° pressure angle tooth thickness Sxn5.12 fixed string Addendum Coefficient string f1 fixed gear tooth thickness measurement most high hxn2.42 Teeth z12 2, shaft wear and tear maintenance: Axis gear pump wear is mainly because with the support roller shaft at both ends between the friction and wear, so that smaller shaft diameter.

分度圆直径：d=mz=3X12=36 齿顶高：ha=m（f0+x）=3X（l+0.5）=4.5 齿根高：hf=m（f0+c-x）=3X（l+0.25-0.5）=2.25 齿全高：h=ha+hf=4.5+2.25=6.75 齿顶圆直径：Da=d+2ha=36+2X4.5=45 固定弦齿厚：Sxn=m（π/2*cos2a+xsin2a）=3X（1.387+0.6428X0.5）=5.125 固定弦齿厚测量用齿高：hxn=m（π/8*sin2a+xsin2a）=3X（0.7476X0.117X0.5）=2.42 模数m3变位系数x0.5 齿形角o20°固定弦齿厚Sxn5.12 齿顶高系数f1固定弦齿厚测最齿高hxn2.42 齿数z12 2、轴的磨损维修：齿轮泵中轴的磨损主要是因为轴两端与支撑滚针间的摩擦磨损，使轴径变小。

By using Zernike polynomials to describe the wavefront distortion of beams, the propagation properties of the flattened Gaussian beams, super Gaussian beams, Gaussian beams and plane waves passing through an aberrated lens or an aberrated annular lens are studied based on the generalized Huygens-Fresnel diffraction integral.

以广义惠更斯—菲涅尔衍射理论为基础，采用Zernike多项式描述像差光束畸变波前相位，研究了平顶高斯光束、超高斯光束、高斯光束以及平面波通过像差透镜和环状像差透镜的传输。

By getting over the state of the art about the technique of the tailrace tunnel with sloping ceiling, the research contents and study ways and means are put forward, and the importance to research is explained.

第二章：主要论述了变顶高尾水洞的工作原理、体型设计和适用条件以及过渡过程计算的数值计算模型，重点在于数学模型的建立与分析，明满流交替现象中选择了合理的计算模型和计算方法；第三章：着重介绍了向家坝变顶高尾水洞方案模型试验的研究内容和主要结果。

By getting over the state of the art about the technique of the tailrace tunnel with sloping ceiling, the research contents and study ways and means are put forward, and the importance to research is explained.Chapter 2 introduces the working principle of the tailrace tunnel with sloping ceiling. And the design of body type, appliance condition and the numerical model for transient process are illuminated.

第二章：主要论述了变顶高尾水洞的工作原理、体型设计和适用条件以及过渡过程计算的数值计算模型，重点在于数学模型的建立与分析，明满流交替现象中选择了合理的计算模型和计算方法；第三章：着重介绍了向家坝变顶高尾水洞方案模型试验的研究内容和主要结果。

To all project practicality, the introduction is given to the operational characteristics, the methods for calculation and the researching actuality of the tail tunnels with sloping ceiling underground hydropower stations the Three Gorges. This paper has discussed in detail the characteristic method being the same with the compressive flow and the Priessmann solution being the same with the free-surface-pressure flow. And how to deal with boundary conditions has been expatiated. Also hydraulic transient process of tremendous load fluctuation in the tail tunnels with sloping ceiling has been numerical simulated and the Fortran program for numerical simulation has been given. The paper gain the maximal press for tail end of the shell, the maximal rising rate of rotational speed of generating set, the maximal vacuum degree for inlet of the tail tunnels and so on under 11 kinds conditions of tremendous load fluctuation. These conditions include the design conditions, the check conditions and the superposition conditions. Finally, the computing results have been analyzed and summarized. The end chapter is the general comment of the whole-length content and the describing of the intending view of researching.

本文以三峡右岸地下电站尾水洞设计为背景，从工程实际出发，阐述了变顶高尾水洞的工作特性、使用范围及其研究现状；详细论述了适用有压流的特征线法、适用明满交替流的普里斯曼解法等数学模型；边界条件的给定和明满交替流的计算方法；用Fonran语言编制了数值计算程序，对三峡右岸地下电站变顶高尾水洞的大波动工况进行了数值模拟，分别得出了在设计工况、校核工况和叠加工况下蜗壳末端最大压力上升值、机组最大转速上升值和尾水管进口最大真空度等重要参数；对数值计算结果进行了详细分析并得出了有价值的结论；最后展望了今后水电站变顶高尾水洞的研究方向。

The water flow movement basic equations of transient process caused by small fluctuation in the inclined roof tailrace system were deduced, and then analyzed and calculated.

推导了变顶高尾水系统小波动过渡过程水流运动的基本方程，对基本方程进行分析与求解，并以某电站为例，探讨了变顶高尾水系统小波动过渡过程的基本规律。

If you lift the whole car with a vehicle lift, you can repair the car under it.

假如你用顶车机把整部车子顶高，你可以在车子的下面维修。

You should now be a medical examination once a week, we recommend that you do a B-see fetal biparietal diameter size, if more than 9.6, you高不高the physical, then he broke the middle palace.

你现在应该是一周体检一次了，建议您去做个B超，看看胎儿的双顶径大小，如果超过9.6的话，你本人身高不高的话，还是破宫产。

The stub gear tooth is often adopted in the involute planetary gear transmission with a few tooth number difference.

在渐开线少齿差行星传动中通常使用短齿，其齿根高与正常齿相同，而齿顶高小于正常齿。

The altostratus base is 2 km high, and cloud top is higher than 5 km. The supercooled water exists abundantly in the cloud, the maximum is up to 0.21 g.m-3 at -11.20℃, but its distribution is not homogeneous, 87%of continuous distribution width are less than 2.4 km, which is disadvantage to the rime increasing of ice crystal in the cloud. Meanwhile, the evaporation effect of subcloud raindrop is very big, the diameter of raindrops which could not arrive the ground is less than 1 mm. Therefore, The cold vortex process produces the weak precipitation.

As云底高2 km，云顶高大于5 km，云中存在比较大的过冷水区，-11.2℃时的过冷水含量0.21 g.m-3，但过冷水的含量分布极不均匀，大于0.05 g.m-3的过冷水区连续分布的宽度87%小于2.4 km，不利于云中冰晶的连续凇附增长；同时云下雨滴的蒸发效应大，直径小于1.0 mm的雨滴难以落到地面，因此本次过程只产生弱的降水。

与顶高相关的网络解释 [注：此内容来源于网络，仅供参考]

acrosome：顶体

精子形成的主要变化是:①细胞核染色质极度浓缩,核变长并移向细胞的一侧,构成精子的头部;②高尔基复合体形成顶体泡,逐渐增大,凹陷为双层帽状覆盖在核的头端,成为顶体(acrosome);③中心粒迁移到细胞核的尾侧(顶体的相对侧),发出轴丝,

addendum circle：齿顶圆

齿顶高 addendum | 齿顶圆 addendum circle | 齿根高 dedendum

addendum：齿顶高

齿侧间隙 backlash | 齿顶高 addendum | 齿顶圆 addendum circle

addendum：齿顶高,齿顶

Adapter sleeve 紧固套,连接套 | Addendum 齿顶高,齿顶 | Addendum circle 齿顶圆

busby：高顶皮军帽

busbar 汇流条 | busby 高顶皮军帽 | Buser 布瑟牌手表

chimney-pot hat：高顶礼帽

chimney 灯罩 | chimney-pot hat 高顶礼帽 | chimp jacket 琴普茄克

top hat：高顶丝质礼帽

bowler hat 圆顶硬礼帽 | top hat 高顶丝质礼帽 | Panama hat 巴拿马草帽

high silk hat：高顶硬礼帽

high silicon Monel 高硅蒙奈尔合金 | high silk hat 高顶硬礼帽 | high socks 高统袜

spanner：扳手;"士巴拿

顶针不够力,使产品局部被顶坏,从产品正面看,有明显的白色或者胶位高出,又叫顶高 水口烘印: 潜水时入水点在制品外观面上留下的痕迹咬花=蚀纹/喷沙 ;逃料=偷料 ;多肉=多料机械类工具类: 扳手=士巴拿(spanner)

high-crowned arch：高顶拱

high-creep strength steel ==> 高蠕变强度钢 | high-crowned arch ==> 高顶拱 | high-current plasma arc welding ==> 大电流等离子弧焊