- 更多网络例句与间隙配合相关的网络例句 [注：此内容来源于网络，仅供参考]
-
In fact, this is a clearance fit with its important role.
其实这个间隙配合是有着它的重要作用的。
-
The present invention includes guide shaft connected to universal shaft coupling; small box and large box clearance fitted with and fixed to the guide shaft; support rod with one end connected to the notched blocks inside the small box and large box and the other end connected to the roller and the sensor; and sensor fixed onto the installing frame and compression spring set inside the large box; and all these together with the pipe constitute one umbrella-shaped structure.
本发明导向轴与万向联轴节固定联接，小箱体、大箱体与导向轴是间隙配合，并在导向轴固定；支承杆一端联接于小箱体与大箱体中的凹形块，另一端与滚轮联接；传感器固定于传感器安装架上，压缩弹簧设置于大箱体中；支承杆一端与小箱体、大箱体中凹形块联接，另一端与滚轮、传感器安装架联接，支承杆沿半径方向圆周均匀分布，与小箱体、导向轴和管道组成一个伞式结构，支承杆与大箱体、导向轴和管道组成另一个伞式结构。
-
In fact, there is little pump of the fluid loss, which makes the operation of pumps can not achieve 100% efficiency, as these fluids are used to on both sides of bearing and gear lubrication, and the pump body is also not possible with no gap, it can not be so that 100% of fluid discharged from the export, so a small amount of fluid loss is inevitable.
实际上，在泵内有很少量的流体损失，这使泵的运行效率不能达到100％，因为这些流体被用来润滑轴承及齿轮两侧，而泵体也绝不可能无间隙配合，故不能使流体100％地从出口排出，所以少量的流体损失是必然的。
-
The three types of fit are: clearance, interference and transition.
可以把配合分为三类：间隙配合，过盈配合，过渡配合。
-
Keywords Calculation method;Clearance fit;Mathematical Model;Standard tolerance;Fundamental deviation
计算方法；间隙配合；数学模型；标准公差；基本偏差
-
When machining parts with bore as positioning reference, if clearance fit positioning is adopted, machining accuracy is certainly affected due to the existence of clearance.
在精加工以内孔为定位基准的零件时，所用芯轴类工装如果采用间隙配合定位，由于定位间隙的存在，必然影响零件的加工精度。
-
In this study, the dynamic effect of different types of motor rotor, including the interference fit and clearance fit, are discussed by the experiment of modal testing and theoretical analysis.
本文藉由模态测试与分析分别探讨马达转子干涉配合及间隙配合於心轴上所造成的动态特性影响，并提出可的有限元素建模方式，藉由模态测试与有限元分析结果的比对显示，证明此种建模方式之确性，能做为未工具机主轴设计开发考。
-
Among refrigerant leakages are caused by clearance fit in rolling piston compressors, the maximal amount of leakage is occurred in the radial clearance, which is mainly processed by the mode that the refrigerant dissolves into the lubricant.
在滚动转子式压缩机内由于间隙配合造成的制冷剂泄漏中，转子径向间隙的泄漏量最大，它主要是以溶于润滑油的形式泄漏的。
-
The study discussed the influence on the dynamic performance of built-in high speed spindles which the assembly of shaft-bearing system include the clearance fit and the interference fit.
本文针对内藏式高速主轴之马达转子以间隙配合及干涉配合种同的配合方式，分别组装於心轴上，探讨其对主轴动态特性之影响。
-
A APDL program is developed for analyzing the contact stress of journal bearing pair of roller cone bit. The 25 contact stress cases of different clearance fit(including clearance of large bearing is bigger, equal to and smaller than that of small bearing) journal bearing pair of the 8 1/2XXX roller cone bit are analyzed. The result is that the maximum contact stress is less when the clearance of large journal bearing pair is smaller than or equal to that of small journal bearing pair.
用参数化设计语言APDL编制了牙轮钻头滑动轴承的ANSYS接触有限元分析程序，根据钻头制造厂方提供的某8 1/2的轴承配合间隙尺寸，分三种不同的间隙配合（大轴间隙大于小轴间隙、大轴间隙等于小轴间隙、大轴间隙小于小轴间隙），共25种情况，对轴承的表面的接触应力进行了分析，得出：大轴间隙小于等于小轴间隙时最大应力比较小。
- 更多网络解释与间隙配合相关的网络解释 [注：此内容来源于网络，仅供参考]
-
fit tolerance：配合公差
配合公差(fit tolerance)是指组成配合的孔、轴公差之和. 它是允许间隙或过盈的变动量. 孔和轴的公差带大小和公差带位置组成了配合公差. 孔和轴配合公差的大小表示孔和轴的配合精度. 孔和轴配合公差带的大小和位置表示孔和轴的配合精度和配合性质.
-
interword gap：字间间隔,字间隙
interwine 缠绕 | interword gap 字间间隔,字间隙 | interwork 互相配合
-
clearance fit：间隙配合
clearance angle 后角 | clearance fit 间隙配合 | clearance for expansion 膨胀间隙
-
clearance fit：动配合
clearance fee 结关手续费 | clearance fit 动配合 | clearance fit 间隙配合
-
clearance fit：间隙配合, 动座配合, 活动配合
clearance fee ==> 出港手续费 | clearance fit ==> 间隙配合,动座配合,活动配合 | clearance for expansion ==> 膨胀间隙
-
fit clearance：配合间隙
fist 拳;笔迹;指标 | fit clearance 配合间隙 | fit error curve 拟合误差曲线
-
close sliding fit：特小间隙滑动配合
Close running fit 紧动配合 | Close sliding fit 特小间隙滑动配合 | Contraction fit 冷缩配合
-
contraction fit：冷缩配合
Close running fit 紧动配合 | Close sliding fit 特小间隙滑动配合 | Contraction fit 冷缩配合
-
running fit：间隙配合
running experience 运行经验 | running fit 间隙配合 | running fit 松动配合
-
running fit：松动配合
running fit 间隙配合 | running fit 松动配合 | running fit 转动配合