- 更多网络例句与镗孔相关的网络例句 [注：此内容来源于网络，仅供参考]
-
Power of the lathe, and rigid, and a wide range of spindle speed for a strong or high-speed cutting can be turned face, cylindrical, inner hole, as well as the metric system, English, modulus, diametral pitch a variety of threads, and bear the drilling, sets of materials, technology, etc. Boring.
本车床功率大，刚性强、主轴调速范围广，适用于强力或高速切削，可以车削端面、外圆、内孔以及公制、英制、模数、径节各种螺纹，并可承担钻孔，套料、镗孔等工艺。
-
Point-to-point systems are suitable for hole-machining operations such as drilling, countersinking, counterboring, reaming,boring, and tapping.
点位系统适用于钻孔、锪孔、扩孔、铰孔、镗孔、攻丝等孔加工。
-
Point-to-point systems are suitable for hole-machining operations such as drilling, countersinking, counter boring , reaming, boring , and tapping.
点位系统适用于钻孔、锪孔、扩孔、铰孔、镗孔、攻丝等孔加工。
-
Point-to-point systems are suitable for hole-machining operations such as drilling, countersinking, counterboring, ream ing,boring, and tapping.
点位系统适用于钻孔、锪孔、扩孔、铰孔、镗孔、攻丝等孔加工。
-
If a bored hole is chattering because of an overextended boring bar don't expect the machine to correct the fault.
如果由于镗刀杆伸出过长导致镗孔加工出现振动，那就不要指望机床能修复这种故障。
-
The boring bar was designed into a new structure consisting of two coaxial bars. As a result, the micro-boring bar can be made with relatively smaller outer diameter, which was suitable for boring smaller and deeper hole, even the measuring and compensating sensors have been incorporated.
但是，在镗削加工中就遇到了较大困难，因为镗杆的径向尺寸受到被镗孔尺寸的严格限制，用于误差在线检测的传感器和用于误差在线补偿驱动的传感器不能直接安装在镗杆内。
-
As the ship stern shaft bearings not before, according to Stern stern tube axis Boring map (SC5084 - 425-02-06), after housings Boring to provide size of the front and bow closures linked to the provisions of Department Boring size.
由于本船艉轴没有前轴承，根据艉轴艉管镗孔图（SC5084-425-02-06），将后轴承座镗孔至规定尺寸，以及将前部与艏密封盖联结处镗至规定尺寸。
-
This machine can be used drilling,core drilling, reaming,boring,tapping, spot-facing and chamfering etc.
可以进行钻孔、扩孔、铰孔、镗孔、攻丝、锪平面，倒角等工作。
-
Bored pipe shall not be considered to be usable for the fabrication of orifice meter tubes until the design engineer has reviewed the data authorized its utilization by means of his signature on the data sheet.
如果未经设计工程师检查数据，并在数据表上签名认可，镗孔后的管子不得用来安装孔板流量计的管子。
-
Check the worn situations of piston ring, cylinder bore, connection rod small end bushing and connection rod bore; replace them as necessary except for cylinder bore can be bored or add repair using cylinder liner
4.4.3检查活塞环、气缸孔、连杆小头衬套及连杆轴孔的磨损情况，必要时除气缸孔可镗孔或加修理用缸套外，其余则可更换
- 更多网络解释与镗孔相关的网络解释 [注：此内容来源于网络，仅供参考]
-
bore hole：钻孔,镗孔
border condition 边界条件 | bore hole 钻孔,镗孔 | boring 镗
-
TQC：倾斜型粗镗刀 最小镗孔直径-刀柄工作长度
TZC 直角型粗镗刀 最小镗孔直径-刀柄工作长度 | TQC 倾斜型粗镗刀 最小镗孔直径-刀柄工作长度 | TF 复合镗刀 小孔直径/大孔直径-孔工作长度
-
rebore：重镗 重镗孔
rebondingofmouldingsand 型砂翻新 | rebore 重镗 重镗孔 | reborer 重镗孔钻
-
uprighting tool：镗孔工具,镗孔工具
upright-drilling machine 立式钻床 | uprighting tool 镗孔工具,镗孔工具 | uprise of salt 返盐,盐分上升
-
bore bit：镗孔钻头
borderline node 边线结点 | bore bit 镗孔钻头 | bore hole 镗孔
-
bore bit：镗孔钻头,镗孔钻头
bore axis ==> 炮膛轴 | bore bit ==> 镗孔钻头,镗孔钻头 | bore brush ==> 炮刷,枪刷
-
precision boring bar：精密镗孔刀杆
precision board cutting saw 精密裁板机 | precision boring bar 精密镗孔刀杆 | precision boring tool shank 精密镗刀杆
-
rod boring machine：连杆镗孔机
rod bore;连杆孔 | rod boring machine;连杆镗孔机 | rod bushing installation;连杆衬套安装
-
connecting rod boring machine：连杆镗孔机
connecting rod bore;连杆孔 | connecting rod boring machine;连杆镗孔机 | connecting rod cap;连杆盖
-
reboring：重镗孔
reborer ==> 重镗孔钻 | reboring ==> 重镗孔 | reboring of worn cylinder ==> 磨损汽缸重镗