- 更多网络例句与锻造工作相关的网络例句 [注：此内容来源于网络，仅供参考]
-
Under static load, and the impact of lower load mode or hot extrusion press forging die.
此钢系高强度热作模具钢，可用于制造工作温度≥550℃并承受较高的静载荷，而冲击载荷较低的锻造压力机模或热挤压模具。
-
Based on the construction features of the Upper Beam of Large Open-die Forging Hydraulic Press,a finite element model has been established by using large-scale finite element analysis software I-DEAS,and the structural stress and displacement of the upper beam under all sorts of loads have been analyzed.
根据某大型自由锻造油压机上横梁的结构特点，利用大型通用有限元分析软件I-DEAS建立有限元模型，并对上横梁进行了静力学的有限元分析计算，研究了在满负荷工作状态下上横梁的结构应力以及位移情况。
-
At least 8 years experience in forging or metal working, at least 4 years of managemental experience.
至少8年以上的金属锻造方面工作经验，其中4年的管理经验。
-
At least 8 years experience in forging or metal working, at least 4 years of managemental experience.
工作经验 Experience：至少8年以上的金属锻造方面工作经验，其中4年的管理经验。
-
And as a corporate secretary, which needs the training and forging, to coordinate the work can be escorting?
而作为一个企业秘书，需要哪些方面的培养与锻造，才能为协调工作保驾护航？
-
YJ13/5000 forging hydraulic forging maximum 50 tons of forgings, the biggest trip of 2000 mm, 4000 mm clearance distance, table size 6000 mm * 4000mm, the itinerary 2 * 3000 mm, the number of forging 40 beats / min, structural advanced.
YJ13/5000锻造液压机最大可锻造50吨锻件，最大行程2000mm，净空距4000mm，工作台面尺寸6000mm*4000mm，工作行程2*3000mm，锻造次数40次/min，结构先进。
-
Under static load, and the impact of lower load mode or hot extrusion press forging die.
此钢系高强度热作模具钢，可用於制造工作温度≥550℃并承受较高的静载荷，而冲击载荷较低的锻造压力机模或热挤压模具。
-
Crack reasons for this are: the heating temperature is too high as a result of quenching or cooling in a hurry, the quality of thermal stress and metal volume changes in the organization of the anti-stress than the breaking strength of steel; the work of the original surface defects (such as surface micro-cracks or scratches) or the internal defect of steel (such as slag, serious non-metallic inclusions, white point, the residual cavity, etc.) formed in the quenching stress concentration; serious Decarburization and carbide surface segregation; parts after quenching Back lack of timely or tempering fire; processes in front of the stress caused by excessive cold red, forging folding, turning deep marks, sharp edges and corners, such as the oil groove.
造成这种裂纹的原因有：由于淬火加热温度过高或冷却太急，热应力和金属质量体积变化时的组织应力大于钢材的抗断裂强度；工作表面的原有缺陷或是钢材内部缺陷（如夹渣、严重的非金属夹杂物、白点、缩孔残余等）在淬火时形成应力集中；严重的表面脱碳和碳化物偏析；零件淬火后回火不足或未及时回火；前面工序造成的冷冲应力过大、锻造折叠、深的车削刀痕、油沟尖锐棱角等。
-
A closed-loop control system using Motorolas MEK6800D2 microcomputer for a quick-acting free-forging hydraulic press aggregate is described.
本文报道了采用MEK6800D2微型计算机的自由锻造液压机组的闭环控制系统，阐明了其总体方案、特点、接口设置以及多重中断处理的硬件电路，介绍了部分服务程序、锻造控制程序和专用监控程序的程序流程图以及为提高系统工作可靠性所采取的措施。
- 更多网络解释与锻造工作相关的网络解释 [注：此内容来源于网络，仅供参考]
-
hammerhead crane：锤头式起重机
hammered work 锻造工作 | hammerhead crane 锤头式起重机 | hammerhead key 银锭榫
-
ipy inches per year：英寸/年
smith work 锻造工作 | ipy inches per year 英寸/年 | regulation of output 输出稳定(振幅)
-
polychrome printing：套色印刷, 多彩印刷法
prodorit 普罗多里特(一种石英与沥青捏炼产品) | polychrome printing 套色印刷, 多彩印刷法 | smith work 锻造工作
-
trimming：去毛边
其结果则将造成更高的模具负荷. 因此,锻造工程道次及模具必须同时依据所需之要求一并考量,相互修正. 因此,各附加的中间形状(Additional Intermediate-shaping)、去毛边(Trimming)或加热工作必须考虑其中的变化量及金属流动的特性.
-
hammered work：锻造工作
hammered steel ==> 锻钢 | hammered work ==> 锻造工作 | hammerhead crane ==> 锤头式起重机