- 更多网络例句与铸道相关的网络例句 [注：此内容来源于网络，仅供参考]
-
They are Trembling Reed, Pure Edge, Defeater of Evil, Fish Intestine and the Great Tower. Now, the Trembling Reed is in Chuh.
薛烛磕头道：小人曾听先师言道，先师为先王铸剑五口，大剑三，小剑二，一曰湛卢，二曰纯钧，三曰胜邪，四曰鱼肠，五曰巨阙。
-
Lubrication system mainly consists of oil pool, oil pump, oil filter, valves, and cast in the way of oil launched.
润滑系统主要由油池、机油泵、机油滤清器、阀门装置及铸于发动机体的油道组成。
-
In the event of the Golden calf, God said, They have quickly turned aside from the way which I commanded them.
在金牛犊的事件中，"他们快快偏离了我所吩咐的道，为自己铸了一只牛犊，向他下拜献祭…。。"
-
They have made for themselves a golden calf and have worshiped it and sacrificed to it and said,'These are your gods, O Israel, who brought you up out of the land of Egypt!'
他们快快偏离了我所吩咐的道，为自己铸了一只牛犊，向他下拜献祭，说：『以色列啊，这就是领你出埃及地的神。
-
The filling process was simulated to analyze local overheat in die resulting from irrational filling and cold shut occurred in far-end in aluminum alloy engine bracket.The results indicate that the defects are caused by irrational ingate design.
针对铝合金摩托车发动机支架在压铸生产中充型不合理导致模具局部温度过热以及铸件充型远端容易出现冷隔缺陷等问题，运用数值模拟方法对压铸工艺过程进行分析，发现内浇道结构不合理是导致以上问题的主要原因。
-
He went up to Priam and said, Son of Laomedon, the princes of the Trojans and Achaeans bid you come down on to the plain and swear to a solemn covenant.
端着闪亮的兑缸和金铸的杯盅。他站在老人身边，大声催请道：劳墨冬之子，起来吧，驯马和特洛伊人和要你前往平原，封证他们的誓约。
-
To decrease the casting pinholes,there should be higher pouring temperature and a suitable sprue height and area.
为减少铸铝件的针孔，铝合金消失模铸造应有适当高的浇注温度和合适的直浇道高度及面积，并尽量采用空心直浇道。
-
The investigation in surface lineal defect of rod are carried on by means of metallograph,grinding test as well as deformation test during roughing roll.
通过对试样进行金相分析，对铸坯表面修磨试验结果分析及对连铸坯在高线粗轧第1道和第2道轧制的受力和变形的分析，发现盘条表面的一种特殊的线状缺陷形成的原因是连铸坯存在边内裂和皮下气泡，粗轧机组(特别是第1和第2架)孔型设计不合理，也促进这种线状缺陷的形成。
-
The flow status of liquid metal in the sand box of group casting was discussed according to the fluid mechanics and heat transfer theory. Not only does the appearance of vying liquid metal happen when group casting between the big and small castings, identical castings in the multiple gates system appear too, even one casting.
运用流体力学、传热学原理，分析群铸时液态金属在各型腔内的流动情况，揭示出争铁液现象不仅在大小件混铸时发生，在多个内浇道浇注系统中群铸相同铸件，甚至仅一个铸件仍存在这一现象。
-
It is suggested that this defect is originated from the internal crack and the subcutaneous bubble s of billet,as well as unreasonable pass design of roughing mill.
通过对试样进行金相分析，对铸坯表面修磨试验结果分析及对连铸坯在高线粗轧第1道和第2道轧制的受力和变形的分析，发现盘条表面的一种特殊的线状缺陷形成的原因是连铸坯存在边内裂和皮下气泡，粗轧机组(特别是第1和第2架)孔型设计不合理，也促进这种线状缺陷的形成。
- 更多网络解释与铸道相关的网络解释 [注：此内容来源于网络，仅供参考]
-
sprue former：铸道形成针
spring wire 弹簧丝 | sprue former 铸道形成针 | spud 铲,剥皮刀
-
tab gate：護耳澆口
ダイレクトゲートdirect-gate直接浇口 | タブゲートtab gate护耳浇口 | スプルーsprue浇口,铸口,浇道
-
bottom pouring：底铸法
从盛钢桶铸入钢锭模之方法有顶铸法(Top pou-ring)与底铸法(Bottom pouring)两种,如图六-20所示. 底铸法系将钢液注入管,经由耐火物制成的流道到数支钢锭模底部流入模内;因同时流入数支钢锭模的关系所以速度比顶铸法为慢且稳静,
-
Spud：铲,剥皮刀
sprue former 铸道形成针 | spud 铲,剥皮刀 | spur crusher 骨刺压碎器
-
tunnel gate：潜伏浇口
スプルーsprue浇口,铸口,浇道 | トンネルゲートtunnel-gate潜伏浇口 | サイドゲートside gate侧浇口