- 更多网络例句与铸模相关的网络例句 [注：此内容来源于网络，仅供参考]
-
The thesis presents a new type of practical die structure with tightwire and idler wheel for angle core pulling of die casting a angle bracket of aluminium alloy.
本文给出了生产铝合金斜支架铸件的新型钢丝绳-滚轮斜抽芯压铸模实用结构，论述了模具结构特点和工作原理。
-
The filling process and temperature field of the die has been coupling simulated by using software of ProCAST, from which the filling states and temperature changes of the die was shown animatedly.
利用ProCAST软件对铝合金压铸模具进行温度场和流场的耦合模拟，动态展示了模具的充型过程和模具稳定工作时的温度场变化。
-
Now when I made the molds this time I have a small channel at the root of each appendage.
现在，当我提出铸模这个时候我有一个小频道的根源，每一个附庸。
-
The boundary conditions and the latent heat of heat transfer system have been treated by heat-enthalpy method.
在这样的充填条件下，虽然金属压铸模的导热性很高，蓄热能力很强，但要求在压铸模型腔内获得形状完整、轮廓清晰、尺寸精度高的铸件，必须得选用合理的模具结构和压铸工艺，而压铸模具的尺寸精度和使用寿命在很大程度上取决于其在压铸过程中热应力和其产生的变形。
-
The experiment of hot dip aluminizing had been carried out in order to study the interaction between die casting die and aluminum alloy and the effect of Si on soldering tendency between die and aluminum alloy casting.
为了研究压铸模与铝合金的相互作用，探讨Si对压铸模与铝铸件焊合倾向性的影响，进行了热浸铝试验。
-
According to researching technical speciality of Al-Si-Cu alloy,making choice of fit clearance of die casting mould shaped part is necessary,then in virtue of mould temperature-controller and midway anneal measure gains the results of increasing quality of die casting and prolonging service life of mould.
通过对铝硅铜合金工艺特性的研究，提出选定合理的压铸模成形零件配合间隙的必要性，并借助模具温控装置、模具中间退火等工艺措施，达到既提高压铸件的质量，又延长压铸模使用寿命的目的。
-
And the designing method, naming and application of the standard die set s of the die_casting die were introduced.
分析了企业内部制定压铸模模架标准的必要性，介绍了压铸模标准模架的设计方法、命名及应
-
Hazards presented by molds that may produce mycotoxins should be considered the same as other common molds which can grow in your house.
危害提出铸模这可能会产生霉菌毒素，应考虑同其他共同铸模，可以增加你的房子。
-
A new die-casting die fit on cold chamber die casting machine was redesigned in the part of the center gate and floating flow-distribution.
分析了录音机芯飞轮压铸模的原设计失败的原因，重新设计了用于冷室压铸机的中心浇口、浮动分流的压铸模。
-
This research sets the target of zinc die-casting design, the craft parameters parts crafts analysis, the choice of die-casting machines and platoon Yak system design, the introduction of institutions, national aircraft design, shape parts design, structural components design, die-casting mould technical requirements and material composition, a total of nine chapters.
本课题研究的对象是锌套的压铸模设计，包括工艺参数的选择，零件的工艺分析，压铸机的选用及排溢系统的设计，推出机构，模架的设计，成形零件的设计，结构零件的设计，压铸模的技术要求及选材等，本课题的设计论述出了各部分的设计方法与原则以及计算设计过程和必要的强度校核。
- 更多网络解释与铸模相关的网络解释 [注：此内容来源于网络，仅供参考]
-
bismuth mold：铋铸模
matched mould thermal forming 对模热成形模 | bismuth mold 铋铸模 | landed plunger mold 有肩柱塞式模具
-
foundry blacking：铸模涂料
foundry alloy 中间合金 | foundry blacking 铸模涂料 | foundry coke 铸造焦炭
-
blackwash：铸模涂料
blacksmith's anvil 锻砧 | blackwash 铸模涂料 | blank 毛坯半制品
-
die bush：进模口套(压铸模)
进模口,闸口 inlet | 进模口套(压铸模) die bush | 晶格,结晶格子 crystal lattice
-
casting：铸模
[技术摘要] 本发明有关一种聚酰亚胺的新颖制法,包括使二酸酐与二胺反应形成聚酰胺酸(polyamic acid)后,藉由将聚酰胺酸涂布或藉铸模(casting)等方法涂布于支持体上,再移除溶剂藉由控制聚酰胺酸的挥发份含量在10重量%以下,
-
mold clamp：铸模夹具
铸模龟裂,脉状痕(铸疵) veining | 铸模夹具 mold clamp | 铸模输送机 mold conveyer
-
mold, mould：铸模
铸漏件 bleeder | 铸模 mold,mould | 铸模布置 mold layout
-
veining：铸模龟裂,脉状痕(铸疵)
铸模除除掉(压铸) impression block | 铸模龟裂,脉状痕(铸疵) veining | 铸模夹具 mold clamp
-
saves：旧锌铸模废料
ROSES-混合常规巴式合金 | SAVES-旧锌铸模废料 | SCABS-新锌铸模废料
-
Scabs：新锌铸模废料
SAVES-旧锌铸模废料 | SCABS-新锌铸模废料 | SCOPE-新镀锌铸模废料