英语人>词典>汉英 : 铸型 的英文翻译,例句
铸型 的英文翻译、例句

铸型

基本解释 (translations)
proplasm

词组短语
casting mould
更多网络例句与铸型相关的网络例句 [注:此内容来源于网络,仅供参考]

And combined with field test of the chain belt vibration, the generation condition of the chain belt vibration and crawling was explored.

结合对铸型机链带振动的现场测试,探讨铸型机链带振动和爬行产生的条件,为铸型机振动和爬行的控制提供依据。

The effects of mold temperature, cooling distance and casting speed on the temperature field in heated mold continuous casting of cupronickel tubes were studied by testing the mold temperature in three points and subsequently calculating with ANSYS.

采用在铸型上定点检测温度,再用ANSYS分析软件计算温度场的方法,研究了铸型温度、冷却距离、连铸速度等工艺参数对白铜管热型连铸温度场的影响。

It can also provide good specimen in cardiovascular learing. Perchloroethylene ethyl acetate plastics filler perfusion is a good technique in making specimen.

该方法能够制作出完整的心脏动脉铸型和局部房室结动脉铸型,标本利于观察分析血管走行及分布,并为解剖实验学习心血管课程提供良好的铸型标本。

Methods Twenty fresh pig hearts,perfusing with perchloroethylene ethyl acetate plastics filler locally,to show the stracture and the ramust of the left and right coronary artery and solid structure of the artioventricular artery sufficiently.

方法新鲜猪心20例,用过氯乙烯-乙酸乙酯填充剂灌注,制作心脏动脉铸型和局部房室结动脉铸型,充分显示左右冠状动脉及其细小分支和房室结动脉的立体构筑。

Dynamic rheological test was introduced and the dynamic shearing modulus G', the loss modulus Gand the complex viscosity of coatings were measured.

把流变动态测试引入铸型涂料的研究,测量出了铸型涂料的动态剪切模量G〓、损耗模量G〓和复合粘度η〓。

The pleural superficial blood vessels were smooth, while the constrictions of smooth muscle cells and round imprints of endothelial nuclei occurred on the surface of the subpleural and parenchymal arteriole and venule.

肺胸膜面浅层微血管的铸型表面光滑,胸膜下和肺实质内微动脉和微静脉的铸型表面可见平滑肌细胞形成的缩窄,以及圆形内皮细胞核的压痕。

In Pattern less casting manufacturing technology by using the disperse/cumuli prototyping principle of rapid manufacturing and resin sand moulding material, the three dimensional CAD model is stratified, sliced, the information of different high section are obtained, then these section are scaned, jet solidify, the resin sand prototyping or casting model is direct obtained.

无模铸型制造技术是以树脂砂为成型材料,利用快速成型技术的离散/堆积成型原理,对三维CAD实体模型进行分层切片处理,得到不同高度截面层的信息,采用截面扫描、喷射固化工艺,直接获得树脂砂铸型或铸造模具的一种方法。

It can also provide good specimen in cardiovascular learing.Perchloroethylene ethyl acet ate plastics filler perfusion is a good technique in making specimen.

该方法能够制作出完整的心脏动脉铸型和局部房室结动脉铸型,标本利于观察分析血管走行及分布,并为解剖实验学习心血管课程提供良好的铸型标本。

Successive steps include adding a concentrated heat reversible gel solution (5) to the flask to cover the critical pattern surfaces (13), and cooling the gel solution to form an elastic solid gel mold (7). The gel mold (7) has critical gel mold surfaces inverse to the critical pattern surfaces.

接下来的步骤包括向烧瓶中加入一个高浓度热可逆凝胶溶液(5)覆盖型面(13),和将凝胶溶液冷却形成一个弹性的固体凝胶铸型(7),凝胶铸型(7)具有与模样型面相反的凝胶铸型型面。

The results showed that the mold hardness of EPC process was higher than that of green sand mold and was more uniformly distributed.

不同真空度下消失模铸型硬度的测试结果表明,消失模铸型的硬度高于普通湿型砂铸型,并且硬度分布更均匀。

更多网络解释与铸型相关的网络解释 [注:此内容来源于网络,仅供参考]

chill mold:冷硬铸型

chill casting 冷硬铸造;冷硬铸件 | chill mold 冷硬铸型 | chilled roll 冷硬轧辊

flowage cast:流动铸型;流铸型

流动 flowage | 流动铸型;流铸型 flowage cast | 硫黄华 flower of sulphur

load-cast lineation:负载铸型线状构造

load-carrying swivel joint 承载旋转接头 | load-cast lineation 负载铸型线状构造 | load-cast striation 负载铸型条痕

load-cast striation:负载铸型条痕

load-cast lineation 负载铸型线状构造 | load-cast striation 负载铸型条痕 | load-deflection curve 载荷-挠度曲线

frondescent cast:菜叶状铸型

free-fall type gravimeter自由落体型重力仪 | frondescent cast菜叶状铸型 | fuels-type refinery燃料型炼厂

frondescent cast:叶状铸型,菜叶状铸型

fromat effector character 格式控制字符 | frondescent cast 叶状铸型,菜叶状铸型 | frondescent furrow flute casting 叶状沟槽铸型

frondescent furrow flute casting:叶状沟槽铸型

frondescent cast 叶状铸型,菜叶状铸型 | frondescent furrow flute casting 叶状沟槽铸型 | front 正面

proplasm:铸型

铸铁碳当量测定仪eutectometer | 铸型proplasm | 铸型出气venting

block pattern:整体铸型

block mold 钢锭模 | block pattern 整体铸型 | block tin 铸锡块

casting box:铸型,型箱

cast-iron body 铸铁体 | casting box 铸型,型箱 | castor oil 苬麻油