- 更多网络例句与金属线制的相关的网络例句 [注：此内容来源于网络，仅供参考]
-
The copperplate painting, is a cave line that was engrave or decays in the metals layout of printed sheet to enter the printing ink, the flat surface part of the layout of printed sheet is after is wipe cleanly then put the bedplate in printing machine, on the mat the paper that wetness lead, cover the son of woollen, bring pressure to print to make but become of.
铜版画，是在金属版面被刻制或腐蚀过的凹线渗进油墨，版面的平面部分被擦干净后，再放在印刷机的台板上，垫上湿润过的纸张，盖上毡子，施加压力印制而成的。
-
In the molecular dynamics simulation model, the metallic thin film and the mold, made of gold and nickel, respectively, are formed in face central cubical single crystal.
本文提出三维分子动力学模型模拟奈米压印之制程，并且研究模具线宽及金属薄膜厚度对於结构成形的影响，模拟中所采用的材料为镍模具及金薄膜，排列的晶格结构为单晶面心立方结构。
-
She knew that somewhere she'd lost track of his growing up: the overbite was gone, he'd grown taller, about the same height as Ken and was no longer skinny but wiry; it'd been many years since he could finally spar on even terms with both Ken and Joe, on occasion humbling them.
她知道那某处她有失去他增加的踪迹在：上面 overbite 不见了，他已经变比较高，关於如同肯恩一般的高度事而且不再是薄的但是金属线制的；因为他可以最后互斗，它已经是许多年在甚至和肯恩和乔称之上，在致使贬抑他们之上。
-
The height of central part of the round cambered surface is equal or higher than the one of ring- shaped bulge. When the horizontal top side of internal cavity of encapsulation mold is pressed down to the heat sink so as to produce a deformation, the cambered surface can not be pressed to oppress the subjacent metal line, and the ring-shaped bulge can also prevent mold-overflow.
该散热片，适用于封装制程，具有一圆形弧面板部，并且其圆形弧面板部的中央是高于或等于环状凸起的高度；如此一来，当封胶模具内模穴的水平顶面下压至散热片上而使其产生变形时，圆形弧面板部就不会压迫到下方的金属线，而环状凸起同样也可发挥防止溢胶的功能。
-
The research had applied metal damascene to fabrication of copper interconnects in III-VA semiconductor devices.
本研究已将金属镶嵌技术运用在三五族化合物半导体之铜金属连线制程上，并讨论此技术在三五族化合物半导体元件上的应用及研发重点。
-
From the temperature (612℃) slightly under its liquidus, the nucleation number was most in the melt, the primary grains were fine and global, the number of grains per area was more, and the optimum holding time was near 30min at 612℃. From the temperature (600℃) below its liquidus, the nucleation number was more, but some nucleuses congregated and grew dendritically.
其中 ，液相线铸造法〔4〕是我们开发的一种新的制浆方法，该法使金属熔体在液相线温度附近保温一段时间并形核，然后浇铸成具有细小球形组织的适合半固态成形的铸坯。
-
Instead, the Gamorreans wore a leather and cloth uniform with metal epaulets that helped hide the shoulder seams.
作为替换方案，加莫人身穿皮革和布制的戏服，饰以金属肩章，掩饰肩部的缝合线。
-
The machines are widely used for drawing wire in the factories such as wire-steel factory,metal mesh factory and nail making factory etc.
用途：本套设备是拉拨低、中、高碳钢线的理想设备，也可拉拨铜、铝等有色金属和合金线材，广泛用于钢丝、钢缆、建筑构件、镀锌铁丝、金属网、制钉等厂矿拉丝之用。
- 更多网络解释与金属线制的相关的网络解释 [注：此内容来源于网络，仅供参考]
-
bimetallic：二金属的, 复本位制的
bimetallic wire | 双金属线 | bimetallic | 二金属的, 复本位制的 | bimetallism | 复本位制
-
Photodetector：光侦检器
Watson研究中心的研究员Min Yang发表了IBM最新设计的单晶矽(monolithic silicon)光侦检器(photodetector),它使用闸极线宽130奈米的互补式金属氧化物矽半导体(CMOS)制程,其资料侦测率(data detection rate)达10 Gbit/second,
-
wiry：金属线制的
wiring 控制线路 | wiry 金属线制的 | wise 方向
-
urethrotome：尿道刀
殊的可伸缩尖端或其他特殊构造.藉膀胱镜置入用来抓取并除去输尿管的结石.此器材一般型包括一个金属线制的篮状物及一个可伸缩的输尿管结石排出器.尿道刀(urethrotome)是置入尿道内切开尿道狭窄并将尿道扩大的器材.此为一金属器械,