- 更多网络例句与金属液相关的网络例句 [注：此内容来源于网络，仅供参考]
-
After the metal liquid flowed alone the batcher drip nozzle, the fluxion was calm and chopping. The dimension of metal grains is even and the stability of production is very good.
金属液流经定量器滴嘴后，能够实现平稳、断续流动，加工的金属颗粒尺寸均匀、稳定性好。
-
Many batcher drip nozzles are installed at the bottom of holding furnace. The molten metal drips to the cooling water box which is mounted under the holding furnace through the batcher drip nozzle. The dwell time of granulated metal is 10~18 seconds in the cooling water box.
在保温炉底部，安装多个定量器滴嘴，保温炉内的金属液流经定量器滴嘴后，滴入保温炉下方的冷却箱内，金属颗粒在冷却水中停留10~18s。
-
The flow of molten metal are the forefront of the lost foam pyrolysis products, it will happen with the liquid metal reflect and affect the quality of metal liquid, if the liquid metal filling process in pyrolysis products should not rule out smoothly, it is easy to cause stomatal , Cockle, by defects such as carbon.
金属液的流动前沿是热解的消失模产物，它会与金属液发生反映并影响到金属液质量，如果金属液充型过程中热解产物不能顺利排除，就容易引起气孔、皱皮、增碳等缺陷。
-
The results show that liquid zinc would nucleate and grow up rapidly on the surface of crystal nucleus eradiation equipment with cooling system when the vibrant equipment was inserted into zinc solution.
为提高铸坯的等轴晶率和凝固组织的均匀性，以金属锌为研究对象进行了大量的振动激发金属液形核实验。
-
High melt surface stability could be obtained when molten metal level is located equally with upside of induction coil.
在电源频率一定的情况下，当金属液面与线圈上平面平齐时，液面波动平缓，在施加相同功率的交变电磁场条件下所得液面形状凸起越高，是电磁铸造所要求的液面状态。
-
It is proposed that the runner location should be first to be selected to ensure molten metal filling along the die wall in order to reduce melt flow resistance and then ingate should be located in the heavy section of the workpiece to which the melt would be filled at the beginning. As a result, the applied pressure could be transmitted fluently to avoid shrinkage cavity and to ensure castings quality.
指出浇道位置的选择首先要保证金属液沿着型壁顺序充填，以减少金属液的流动阻力；内浇道应使液态金属从制件厚壁处开始充填，以利压力的传递，消除缩孔，保证制件的质量。
-
Numerical simulation results show that the fluid flow in Lost Foam Process was different from that in an ordinary green sand mold, the molten metal flow forwards in a circular-arc shape from the ingate, meanwhile, the nature of the gating system influenced the filling process notably. As the polystyrene pattern decomposition has a strong quenching effect on the flowing metal fornt, a high temperature gradient was formed at the flowing metal front, this resulted in the dropping of temperature of the metal to the liquidus temperature quickly and decreased the flowability of molten metal, the temperature distribution in the metal behind, however, was even. The properties of the pattern and the coating affected the temperature distribution remarkably.
从内浇口开始，金属液呈放射状均匀向前充填，同时浇注系统性质显著影响金属液充型过程的流场；由于聚苯乙烯模样气化吸热对金属液的激冷作用，在金属液流端部区域产生很大的温度梯度，使得端部区域金属液很快降至液相线温度，降低了金属液的充型能力，而后续金属液中温度分布则比较均匀，模样性能、涂料性能显著影响这一温度分布特点。
-
Algorithms within the SSR PLC calculate the amount of time to stir the metal based on various monitored process variables such as molten metal temperature and shot size to produce consistent slurry.
半固态工作站的 PLC 通过所监测的各种工艺参数变量，例如融化金属液的温度和浇注重量，来计算金属液搅拌所需的时间以便产生稳定的铝浆。
-
In the electromagnetic field that countercurrent inductor produces, the metal droplet that melts gets the role suspension of electromagnetism force in quartz pipe center and had been heated up continuously. When metal droplet of melting have been heated up certain temperature surface beginning gasification, metal vapor tension will raise follow temperature go up, is heated continuously can have plenty of metal atoms overflow metal ball liquid surface, at the same time, as the inert gas of cooling medium, all along with certain current velocity, sideswipe the metal droplet surface that melts. Metal atoms fly out liquid surface according to certain way form the atom cluster by the condensing of inert air current, merger and the collision between crystal nucleus pellet and atom cluster form the smoke flame of nanoparticle pellet eventually.
在逆流感应器产生的电磁场中熔化的金属液滴受电磁力的作用悬浮于石英管中央并继续被加热，当金属熔球被加热到一定温度时表面开始气化，金属蒸气压随温度的升高而升高，继续受热会有大量的金属原子飞出熔球液面，与此同时，作为冷却介质的惰性气体始终以一定的流速掠过熔化的金属液滴表面，原子飞出液面受冷后就按照一定的方式凝聚成原子簇，在惰性气流中形核并随之长大，颗粒、原子簇间的碰撞与合并，最终形成金属纳米颗粒的烟焰。
-
The properties of carbonized corn straw using as thermal insulating agent for liquid metal were investigated.
针对金属液用保温剂碳化稻壳价格不断上涨和保温效果有待进一步提高的现状，以开发新型、质优价廉保温剂为目的，考察了碳化秸秆的理化性能以及作为金属液保温剂的使用性能。
- 更多网络解释与金属液相关的网络解释 [注：此内容来源于网络，仅供参考]
-
gassy melt：含气金属液
spoiled product 废品 | Pindus 品都斯山脉[南欧巴尔干半岛] | gassy melt 含气金属液
-
Metalworking Fluid：金属加工液
各种工业油Various industrial oils | 金属加工液Metalworking Fluid | 乳化液Cutting emulsion
-
remaining melt：残留金属液
再负载 reloading | 残留金属液 remaining melt | 残留磁气 remanent magnetism
-
Metal Working Fluid：金属加工液
金属加工液(Metal working Fluid)又称金属加工润滑剂,是指用于金属及其合金切削、冲压、轧制和拉拔等各种加工过程中所使用的润滑剂,是金属加工过程重要的配套材料.
-
Metal Working Fluid：金属切削液
metal spraying 金属喷镀 | metal working fluid 金属切削液 | metal 金属
-
metal bath：金属浴,焊接熔池
metal base transistor ==> 金属基极晶体管 | metal bath ==> 金属浴,焊接熔池 | metal bath surface ==> 金属液面
-
metal bath：金属浴,金属熔池,金属熔体
metal base transistor || 金属基底晶体管 | metal bath || 金属浴,金属熔池,金属熔体 | metal bath surface || 金属液面
-
metal bath surface：金属液面
metal bath || 金属浴,金属熔池,金属熔体 | metal bath surface || 金属液面 | metal bath treatment || 金属浴处理
-
metal bath treatment：金属浴处理
metal bath surface || 金属液面 | metal bath treatment || 金属浴处理 | metal break out || 漏箱,跑水,铸型裂口
-
Float tank：浮抛窑(浮法玻璃金属液槽),锡槽
Bloat glass process浮法玻璃生产法 | Float tank浮抛窑(浮法玻璃金属液槽),锡槽 | Float-process浮法(生产)平板玻璃