- 更多网络例句与部分进位相关的网络例句 [注：此内容来源于网络，仅供参考]
-
On a calculator, the increase of the least significant digit in the result of a calculation by one if the highest decimal place dropped off has a value of more than zero.
在计算器中，如果计算结果舍弃的最高位十进位数字大于零，则剩余部分的最低有效位加1。
-
So e answer is that casting from a float or double to an integral value always truncates.
所以 答案就是：将一个float或double值造型成整数值后，总是将小数部分"砍掉"，不作任何进位处理。
-
The design of the device using NC Lathe CA6140 control, part of the main transmission system using AC spindle motor and graded by the pulley driven spindle gearbox, through the inverter and gearbox to achieve sub; Feed System used by stepper motor driven ball screw slowdown after campaign vertical feed system through a gear after the ball screw drive, in the horizontal feed system through two gear-driven ball screw; Tool to automatically transfer tool carrier (4-position), thus achieving automatic tool change; by MCS-51 series 8051 data to be dealt with. from the I / O interface stepper pulse output signal to control the feed rate and itineraries; In order to maintain the function of cutting thread, to the outer end of spindle or other appropriate location loaded pulse generator; Lathe will be transformed into Tailstock manually controlled electric Tailstock.
本设计利用数控装置对CA6140普通车床进行控制，主传动系统部分采用交流调频主轴电动机经带轮及分级齿轮变速箱驱动主轴，通过变频器和齿轮变速箱实现分段无级变速；进给系统采用步进电机通过减速后驱动滚珠丝杠运动，在纵向进给系统中通过一级齿轮减速后驱动滚珠丝杠，在横向进给系统中通过二级齿轮减速驱动滚珠丝杠；刀架改为自动转位刀架从而实现自动换刀；通过MCS-51系列8051单片机对数据进行计算处理，由I/O接口输出步进脉冲信号控制进给速度和行程；为了保持切削螺纹的功能，要在主轴外端或其它适当部位装上脉冲发生器；将车床的手动尾座改造成为可控电动尾座。
-
The design of the device using NC Lathe CA6240 control, part of the main transmission system using AC spindle motor and graded by the pulley driven spindle gearbox, through the inverter and gearbox to achieve sub; Feed System used by stepper motor driven ball screw slowdown after campaign vertical feed system through a gear after the ball screw drive, in the horizontal feed system through two gear-driven ball screw; Tool to automatically transfer tool carrier (4-position), thus achieving automatic tool change; by MCS-51 series 8051 data to be dealt with.
本设计利用数控装置对CA6240普通车床进行控制，主传动系统部分采用交流调频主轴电动机经带轮及分级齿轮变速箱驱动主轴，通过变频器和齿轮变速箱实现分段无级变速；进给系统采用步进电机通过减速后驱动滚珠丝杠运动，在纵向进给系统中通过一级齿轮减速后驱动滚珠丝杠，在横向进给系统中通过二级齿轮减速驱动滚珠丝杠；刀架改为自动转位刀架从而实现自动换刀；通过MCS-51系列8051单片机对数据进行计算处理，由I/O接口输出步进脉冲信号控制进给速度和行程；为了保持切削螺纹的功能，要在主轴外端或其它适当部位装上脉冲发生器；将车床的手动尾座改造成为可控电动尾座。
-
The function that allows the adding of one to the least significant digit in the result of a calculation together with the necessary carries, if any of the highest decimal places dropped off has a value of more than zero.
一种功能，若计算结果的舍弃部分最高位的十进位数字大于零，则使结果中的最低位有效数字加1，并进行必要的进位。
-
To form a partial sum, i.e., to add without carries.
只形成部分和，即不进位的加。
-
A method of high speed carry in parallel addition. With this method, the carry skips the digits with partial sum of 9 or 1.
并行加法中的一种高速进位法，在这种方法中，进位数跳过部分和为9或1的数位。
-
So e answer is that casting from a float or double to an integral value always truncates.
所以 答案就是：将一个float或double值造型成整数值后，总是将小数部分&砍掉&，不作任何进位处理。
-
This production line is composed of filling section, cleaning and drying section, conveying section, light inspection positioning section, automatic plate bonding section, long-journey plate pressing section and automatic discharging turning section.
该生产线由进料段、清洗干燥段、传送段、灯检定位段、自动合片段、大行程板压段、自动出料翻转段等部分组成。
- 更多网络解释与部分进位相关的网络解释 [注：此内容来源于网络，仅供参考]
-
partial confounding：部分混区
partial carry 部分进位 | partial confounding 部分混区 | partial correlation 偏相关
-
decimal of many places：多位十进小数
decimal number system 十进制 | decimal of many places 多位十进小数 | decimal part 小数部分
-
decimal numeration：十进位计数法
decimal number 小数 | decimal numeration 十进位计数法 | decimal part 小数部分
-
decimal numeration：十进位记数法
decimal number system 十进位数字制 | decimal numeration 十进位记数法 | decimal part 小数部分
-
parsing automaton：句法分析自动机
parsing 句法分析 | parsing automaton 句法分析自动机 | partial carry 部分进位
-
partial carry：部分进位
partial 部分 | partial carry 部分进位 | partial sum 部分和
-
carry,partial：部分进位
carry,end-aroand端回进位 | carry,partial部分进位 | carry-completesignal完全进位信号
-
partial function：部分函数
partial carry 部分进位 | partial function 部分函数 | partial matching 部分匹配
-
carry propagate：进位传输
carry portion 进位部分 | carry propagate 进位传输 | carry propagation 进位传送
-
carry propagate output：进位传播输出
进位部分 carry portion | 进位传播输出 carry propagate output | 进位传播 carry propagation