连接螺栓

词组短语

tie bolt · connecting bolt

与连接螺栓相关的网络例句 [注：此内容来源于网络，仅供参考]

Tower crane for high-intensity Anchor Bolt and bolt for Xugong Group abundance of high-strength standard parts Limited production of quality products, the company's special units designated for sale.

塔机专用高强度地脚螺栓和连接螺栓为徐工集团伟丰高强度标准件有限公司生产的优质产品，我公司为该公司的特约指定销售单位。

While install, we should clean the inner to prevent the dirt blocks or the eyewinker damages the sealed parts and check if all the connected bolts are uniformity tight and fast.

4.6安装时，应将阀门内腔清洗干净，防止污垢卡阻或异物损伤密封部件。并检查各部件连接螺栓是否均匀紧固。

Furthermore, open of segment joints, stretch of connected bolts and contact stress distribution on joint faces are the main points which decide whether or not the joint is safe.

同时，接缝的张开、连接螺栓以及接缝处接头面的受力状态是判断接头是否安全的主要依据。

The strength check to the principal axes, bearings, keys and connecting bolts is essential, owing to the rotor is solid of revolution.

由于转子是回转体，所以对主轴、轴承、连接螺栓需进行强度校核。

At this time, loosen the connection screw of standard section with spanner, hang the shaft of hand crane on the upper angle bar, sway the shaft of hand crane upward, separate this standard section from the next section, and lay it in the suspension coop, dismantle the other standard section for the same method, and turn the shaft to another direction, draw the lifting wire rope tightly, the operation staff leave the suspension coop, open the lock stopping instrument, fall the suspension coop to next position and lock the brake instrument, the operation staff return to the top of suspension coop, continually dismantle note: forbid the staff leave on the top of suspension coop or in the coop when the suspension coop is running

8.1折除时，首先将吊笼用停层装置停靠在待拆除的标准节的下两节上，操作人员上到吊笼顶，卷扬机松绳，用小吊杆将顶梁略向上提起，拔出顶梁横销，使顶梁值得徐徐降下，降到拆除节下一节中间框架角处，并重新穿上横销，这时用板手将标准节连接螺栓松开，将手摇起重机小吊杆钩挂在待拆节上框架用钢土，到吊笼内，用同样的方法拆下另一节标准节，然后将吊杆转向不影响升降机运行的方向，收紧起升钢丝绳，操作人员离开吊笼，打开锁止机构，使吊笼下降到下一个拆除位置，并将锁止机构锁死，人员重返笼顶，进行下一拆除循环注意：在吊笼运行时绝不允许有人员留在吊笼顶部或吊笼内

When dismantle the machine, firstly, stop the suspension coop on the lower 2 sections of the standard sections, the operation staff go on the suspension coop top, the hoisting machine loosen rope, lift the pillar with small shaft, pull out the horizontal pin of pillar, let the pillar fall slowly to thedismantled section's middle angle bar, insert the horizontal pin again. At this time, loosen the connection screw of standard section with spanner, hang the shaft of hand crane on the upper angle bar, sway the shaft of hand crane upward, separate this standard section from the next section, and lay itin the suspension coop, dismantle the other standard section for the same method, and turn the shaft to another direction, draw the lifting wire rope tightly, the operation staff leave the suspension coop, open the lock stopping instrument, fall the suspension coop to next position and lock the brakeinstrument, the operation staff return to the top of suspension coop, continually dismantle note: forbid the staff leave on the top of suspension coop or in the coop when the suspension coop is running

8.1折除时，首先将吊笼用停层装置停靠在待拆除的标准节的下两节上，操作人员上到吊笼顶，卷扬机松绳，用小吊杆将顶梁略向上提起，拔出顶梁横销，使顶梁值得徐徐降下，降到拆除节下一节中间框架角处，并重新穿上横销，这时用板手将标准节连接螺栓松开，将手摇起重机小吊杆钩挂在待拆节上框架用钢土，到吊笼内，用同样的方法拆下另一节标准节，然后将吊杆转向不影响升降机运行的方向，收紧起升钢丝绳，操作人员离开吊笼，打开锁止机构，使吊笼下降到下一个拆除位置，并将锁止机构锁死，人员重返笼顶，进行下一拆除循环（注意：在吊笼运行时绝不允许有人员留在吊笼顶部或吊笼内

When need to hoist, they are delivered into work-in frame by weight hooking the tower section, loosen the tower section and the lower ring support by 8 M39 connecting bolts , driving motor so as to make the hydraulic cylinder work, press the upper structure, control latches and support the upper weight, take back the stopcock, jacking it again, after this two working repetition it will gain a tower section.

当需要顶升时，由起重吊钩吊起标准节送进引进架，把塔身标准节与下支座的 8 个 M39 的连接螺栓松开，开动电机使液压油缸工作，顶起上部结构，操纵爬爪支持上部重量，收回活塞，再次顶升，这样两次工作循环可接一标准节。

And pipeline connection, please use the provisions of cross-locking torque flange bolts.

与管道连接后，请用规定的扭矩交叉锁紧法兰连接螺栓。

Rotary valve capacity is about the same size straight trip valve 2 ~ 3 times, spin valve can be used to improve the blending amount of the feed pipe without changing the size, can greatly reduce costs, for this reason, part of the rotary valve has been designed to replace the cut-off valve flange face flange form of connectivity and is equipped with connecting bolts, such valves even better than the cut-off valve replaced them cheaper.

旋转阀的容量大约是相同尺寸的直行程阀的2～3倍，旋转阀能够用于提高掺合量而不改变进料管线的大小，可以极大地降低成本，基于这个原因，部分旋转阀已经设计成可代替截止阀的法兰面对法兰面的连接形式，并配有连接螺栓，这类阀甚至比他们所替代的截止阀还便宜。

Flange joint bolt is just put in from the side of flange joint component, nut screw in from the side of flange of coupling.

法兰连接螺栓只能从被连接构件的法兰侧放入，螺母从联轴器的法兰侧拧入。

与连接螺栓相关的网络解释 [注：此内容来源于网络，仅供参考]

bolted connection：(钢结构)螺栓连接

bolt 螺栓(54) | bolted connection (钢结构)螺栓连接(59) | bolted joint (木结构)螺栓连接(69)

bolted joint：(木结构)螺栓连接

bolted connection (钢结构)螺栓连接(59) | bolted joint (木结构)螺栓连接(69) | bolted steel structure 螺栓连接钢结构(50)

bolted joint：螺栓连接

bolted flange 栓结法兰 | bolted joint 螺栓连接 | bolted pipe coupling 螺栓连接的管接头

Carriage bolt：马车螺栓

较大的螺丝称作螺栓,如:六角螺栓(hex machine bolt),膨涨螺栓(anchors),马车螺栓(carriage bolt)等. 但是一般来说,螺栓用来连接两个物体,通常是通过光孔,需要和螺母(nut)配合使用,单个不起连接作用. 工具一般用扳手. 头部多为六角头等,

Fastening bolt：联结螺栓

fastening bolt 紧固螺栓 | fastening bolt 联结螺栓 | fastening bolt 连接螺栓

Fastening bolt：连接螺栓

fastening bolt 联结螺栓 | fastening bolt 连接螺栓 | fastening coefficient 编队系数

Fastening bolt：紧固螺钉,紧固螺栓,连接螺栓

fastening | 紧固,接紧 | fastening bolt | 紧固螺钉,紧固螺栓,连接螺栓 | fastening of terminals | 端子的紧固

coupling bolt forcer：连接螺栓压入器

coupling amplifier 耦合放大器 | coupling bolt forcer 连接螺栓压入器 | coupling bolt 连接螺栓

bolted pipe coupling：螺栓连接的管接头

bolted joint 螺栓连接 | bolted pipe coupling 螺栓连接的管接头 | bolted pump 螺栓连接泵

bolted steel structure：螺栓连接钢结构

bolted joint (木结构)螺栓连接(69) | bolted steel structure 螺栓连接钢结构(50) | bonded prestressed concrete structure 有粘结预应力混凝土结构(24)