进行试验

基本解释 (translations)

experimentize

与进行试验相关的网络例句 [注：此内容来源于网络，仅供参考]

Based on the research production, with three prestressed concrete hollow slabs from the bridge in active service for ten years, this essay studies the ultimate bearing power ,the load-bearing failure mechanism and structure reenforcement measures influence on them, through examination of each performance index, failing load test, theoretical analysis and computing research work.

对预应力混凝土桥梁结构在使用中存在的问题及国内外相关研究发展水平进行了综述，指出目前对旧桥预应力混凝土空心板实际极限承载能力进行相关研究的必要性及其重大意义； 2、对旧桥预应力混凝土空心板的混凝土强度、碳化深度、预应力筋的锈蚀状况以及裂缝状况的检测评定； 3、通过破坏荷载试验，对损伤旧桥预应力混凝土空心板的受力性能进行试验评定； 4、采用在桥面做混凝土叠合层的加固措施，通过破坏荷载试验对加固后的旧桥预应力混凝土空心板的受力性能进行评定； 5、提出在役旧桥预应力混凝土空心板的维护、加固和使用建议。

The method of orthogonal design is applied in the DOE, and the experiments are simulated. The results are analyzed with the analysis of regression to study the effect of the drive and fuel economy performance by the factor of drive train parameters.

对动力传动系统参数进行试验方案设计，对试验方案进行动力性和基于循环工况的燃油经济性模拟计算，采用回归分析的方法对试验结果进行处理，研究了试验因子及其交互对试验指标的影响，并对参数进行了预测和优化。

In chapter 4, on the basis of academic analysis, an integrated experimentation project is designed, then experiments on eight electrodes respectively including hemisphere、ring、reticulation etc,and gains curves of diversified parameters with increase of current electrode, compares them with parameters of hemisphere electrode.

在第四章，文章以上一章的理论计算为基础设计了完整的模拟试验方案，然后对半球形、环形、棒形、网状、放射形等八种形状的电极分别进行试验，通过整理试验数据得出电流极数目增加时各组参数的变化曲线，分析曲线并将各参数的试验值与半球电极的理论值进行对比。

The index of flame retardant property,material,product structure and relevant method of test of the antiflaming flexible cable is established according to the standard of GB/T18301-2001《the Third Part of Burning Test of cables in the Condition of flame:Method of Buring Test of Bunchy Wires and Cables》.The Cable will emanate the bad gas in buring to causethe the second calamity,so the smoke capacity of the cable in burning should be tested according to the standard of IECl034-2(1991)《the Second Part of Method of Smoke Concentration Test ofCable 1n Burning:Procedure and Requirement ofTest》The Liberation of Gas 1n burning is tested according to the standard of IEC754-2(1991)《the Second Part of Test of Liberatlon of Burning Materlal from Cable:Method to Measure the ACidity with the Measured PH and Conductlvltv》.

对阻燃型软电缆所要求的阻燃性能指标，是根据GB/T18301-2001《电缆在火焰条件下的燃烧试验第3部分：成束电线或电缆的燃烧试验方法》标准的规定而确定其电缆的材料要求、产品结构和相应的试验方法；对于耐火性试验，并考虑到电缆在火焰中会散发有害气体，造成&二次灾害&，所以还规定了对电缆燃烧时发烟量进行试验，按IECl034-2(1991)《电缆在特定条件下燃烧的烟浓度试验方法第二部分试验步骤和要求》以及燃烧时析出气体按IEC754-2(1991)《取白电缆的村料燃烧时析山气体的试验第二部分用测量PH值和导电率来测量气体酸度的方法》进行试验。

Exhaust purity box is experimented in the way of upright meathed times are less for the multielement and multilevets ,the impact degree on the exhaust purity box canbe got from the experiment data analysis of various elements ,be offered to further the improvement of the exhaust purity box .

利用正交设计试验方法对净化消声器进行试验，在较少的试验次数下进行了多因素多水平的试验，从试验数据的分析中可看出各因素对净化消声器各性能的影响程度，为进一步提高净化消声器的性能提供了参考依据。

For the first time, a screw pile and pile driver system for preventing flood and rushing to deal with an emergency was manufactured. The screw piles of the system is different from screw drills used to sap, and it doesn't push soils out. Analyses, including the screw pile's structural strength analysis and the screw blade's welding analysis, were done by ANSYS, which showed that the screw pile's structural strength is enough and that the distort of the screw blade is small. Testing on the screw pile and pile driver system showed that the system performed stably and could meet the need of preventing flood and rushing to deal with an emergency. A mechanics model of interaction of a screw pile and soil was built, and expressions of torque of screw pile's cylindrical part on the condition of screw pile's crew part being driven into soil fully were gained, then the relation of the torque with screw pitch and out diameter of cylinder, which shows the torque decreases with the screw pitch increasing, and that the torque increases with the out diameter of cylinder increasing, which was according with the experiments of the screw pile's being driven into soils, and thus a screw pile with the best structure was chosen. Experiments of bionic surface showed that, on the condition of certain pressure on the surface, the protruding bionic surface can not reduce adhesion and resistance and that the corrugated bionic surface can reduce adhesion and resistance. An orthogonal experiment of the corrugated bionic surface was done with the factors including the width of protrusion, the space between two protrusions, the trolley's velocity and the vertical surface pressure and with the surface frictional coefficient as the experimental target, and some inclusions were drawn that the best combination of the factors was acquired and that the width of protrusion affected the surface frictional coefficient remarkably.

研制了防汛抢险螺旋桩机系统，提高了沉桩作业效率；利用ANSYS对桩体进行整体结构强度分析以及螺旋叶片的焊接分析，表明桩体结构强度足够，焊接过程中，螺旋叶片的变形小；对整个螺旋桩机系统进行试验，表明该系统性能可靠，工作稳定，作业效率高，能够满足防汛抢险沉桩作业基本需要；建立了螺旋桩桩土作用力学模型，得出螺旋桩沉桩过程中螺旋桩螺旋部分完全进入土体时螺旋桩圆柱部分所受扭矩以及扭矩与防汛抢险螺旋桩的螺旋导程和圆柱外径的关系曲线，表明螺旋桩螺旋部分完全进入土体时螺旋桩圆柱部分所受扭矩随着螺旋导程的增大而减小，随着圆柱外径的增大而增大，这与螺旋桩沉桩试验结论相符合，据此优选出最佳结构的螺旋桩；仿生曲面试验表明，尺寸较小的球冠突起型仿生曲面在一定压力作用下未能起到减粘降阻的作用，而尺寸较大的波纹型仿生曲面相对平板具有一定的减粘降阻作用；以波纹型仿生曲面突起宽度、波纹型仿生曲面两突起之间间距、台车的牵引速度以及叶片表面垂直载荷为因素，以曲面摩擦系数试验指标进行正交试验，寻求出在一定试验条件下最佳因素水平组合；波纹型仿生曲面突起宽度在本试验条件下对曲面摩擦系数影响显著，而其它几个因素对曲面摩擦系数影响均不显著；通过波纹型仿生曲面突起宽度和台车牵引速度的单因素试验，表明曲面摩擦系数随着仿生曲面突起宽度的增大而减小，而随着台车牵引速度的变化基本保持不变，和正交试验结果保持一致。

When proceeding pump testing, we collect a good many parameters, and figure out the pump gross head, pump shaft power, NPSH and other parameters. Different units of those parameters are used in different countries, and sometimes the customer asks for the test data of special media. Making a test of every medium of the same pump is not realistic, and the costs will be increase, so we convert the units of the data, and figure out the testing data according to different customer's special requirements. We reduced costs and got good remarks from the corporation through the application of unit conversion technology.

水泵试验时，要采集诸多参数，并且根据这些参数计算出扬程、轴功率、NPSH等数值，不同国家这些参数采用的单位不同，企业必须能够按照客户要求的单位提供试验数据；并且有时客户要求得到水泵在特殊介质下进行试验得出的试验数据，同一台泵在每种介质下都做一遍试验不太现实，而且会提高企业的生产成本，提出将采集的数据进行单位换算，根据不同国家或者客户的特殊要求求出泵的试验数据，在实际应用中节省了试验成本，得到了企业的好评。

Cooperating with enterprise, this project has developed surface adhering sand glass fiber bar and carbon fiber bar, conducting experimental research on mechanical property of FRP bar, measuring main mechanical property indexes of tensile strength, elastic modulus and ratio of elongation, etc.

摘要］对表面粘砂玻璃纤维筋、碳纤维筋试验方法、基本力学性能进行试验研究，测试FRP筋的抗拉强度、弹性模量及延伸率等主要力学性能指标；对FRP筋试验过程、试验方法、破坏形态进行详细介绍，通过对试验结果进行处理，提出了用于构件设计的力学性能指标，供工程技术人员参考。

In this paper, test research have been performed on the two important mechanical properties indicator compressive modulus of elasticity and shear modulus. Numerical simulation has been performed on the base of results of test under the situation uniform and uneven thickness of elastomer layer, which analyze internal stress distribution of the elastomeric bearing, as follows:(1) The traditional test methods of compressive modulus of elasticity test are rather cumbersome and take up experimentalists lots of time. This paper has improved the traditional test methods of compressive modulus of elasticity test, which has collected the holding-load time together to concentrate on holding load. The tests have been performed on different types of bearings, which results show that the results of the improved test method conform to the error range regulated by the standard and can effectively save time for the experimentalists, also eliminate the accumulative error.

本文主要对板式橡胶支座的抗压弹性模量、抗剪弹性模量两个重要力学性能指标进行试验研究，并在试验结果的基础上对均匀胶层厚度和不均匀胶层厚度两种情况进行数值模拟，分析橡胶支座内部应力分布规律，具体内容如下：(1)传统抗压弹性模量试验方法比较繁琐，占用试验人员大量时间，本文对传统抗压弹性模量试验方法进行了改进，将持荷时间集中起来进行集中持荷，通过对不同类型支座进行试验，试验结果表明该改进试验方法所得结果符合标准规定误差范围，为试验人员节省了大量时间，并且还消除了传统方法中的累计误差。

TRW Automotiveis the leader in automotive safety suppliers. We employ approximately 65,000 people in 28 countries. We are headquartered in Livonia, Michigan, USA. Our products include integrated vehicle control and driver...

职位简介：每年会有2~3个月的出差安排主要职责：·保持车辆试验的正常进行·组织运输车辆到相应的地点·进行试验仪器安装·支持仪器调试·协助试验出差事宜·提供驾驶支持·在试验。。。

与进行试验相关的网络解释 [注：此内容来源于网络，仅供参考]

experiment with：进行试验;进行实验

35.take risks 冒险 | 36.experiment with 进行试验;进行实验 | 37.piles of 一大堆;一大批;一大团

Gambia：非 洲 甘比亞

不能轻易让婴儿进行充满未知的临床试验,但婴儿却是遭受疟疾伤害最深的一群. 在非洲甘比亚(Gambia)已完成的成人临床试验中,RTS,S/AS02疟疾疫苗的成效显著,倘若在儿童身上的效果也是十分良好,未来将更进一步於婴儿身上进行试验.

NTS：内华达试验基地

从1951年~1992年,在内华达试验基地(NTS)的地下进行了核装置的引爆试验,造成了地面变形,利用InSAR对此进行了评价. 尽管美国在1992年9月暂停了核试验,核试验延期禁令生效,但是在Yucca Flat(YF)和Pahute Mesa(PM)的5次试验推迟了欧洲空间局ERS1卫星首个SAR存档数据的使用.

Orthogonal design：正交试验设计

说明多因素试验设计的思路:对全面组合的所有试验点通盘考虑,从中选取具有代表性的试验点进行试验、比较展望 六、正交试验设计 (Orthogonal Design) (有称田口方法(Taguchi Methods,

pumping test：抽水试验

在地质钻探或地下水监测井设置的过程中,亦可采取代表性的土壤或岩心样品进行土壤试验,并进行抽水试验(Pumping test)或微水试验(Slug test),以求得加油站的地质水文参数.

qualification test：质量鉴定试验

系统采用现场可编程门阵列(FPGA)芯片控制高速A/D采集CCD数据,根据动态阈值提取杂质数据并进行封装处理,然后通过USB2.0总线传输至上位机进行分析、记录和......本文介绍了5~46kV交联聚乙烯绝缘电缆的质量鉴定试验(Qualification Test)的试验程序、性能要

test on：对...进行试验

21037 be irrelevant to 与...不相干;不切题 | 21038 test on 对...进行试验 | 21039 aim for 瞄准;以...为目标

to test on：对...进行试验

5 be irrelevant to 与...不相干;不切题 | 6 to test on 对...进行试验 | 7 to aim for 瞄准;以...为目标

routine test：常规试验

(2)常规试验(Routine test) 检验产品特性是否与形式试验得到的特性一致. (3)参考试验(Option test) 是和产品的式样、额定参数无直接关系,仅作为了解产品使用过程中的某些能力而进行的试验. (4)组合试验(combined test) 是包括电机和负载在内的整体系统评价试验.

type test：型式试验

100mA是型式试验(type test)的数值,例行试验(routine type)呢?例行试验这个数值取多大,为什么?这才是大多数人要问的问题. 例行试验与型式试验不同,它往往是在生产线上进行的,并且用1到几秒来替代1分钟,这时的分断电流值在不同的标准中出现了很大不同.