- 更多网络例句与进模口相关的网络例句 [注：此内容来源于网络，仅供参考]
-
This dissertation aims to probe into the warpage of flash memory card connecter, forecast the possible question through CAE analysis, and select the most proper type of gate, and optimize it through the differentiation caused by the molding condition regulation with Taguchi-methods.
本论文的目的是在改善与探讨快闪记忆卡连结器架构之翘曲变形现象，应用CAE模流分析软体预测可能发生的问题，选择出最佳的进浇模式，并利用田口方法探讨不同的成型条件设定所可能产生的差异性，并予以最佳化。
-
Analyzed the structure characteristics of the perfume cover outer shell plastics piece, described the piece's structure and work principle which model a craft and inject a mold, its principle :adopt and certainly be apart from bolt and spring coil and carry on two cents type, use inclined lead a side outside the pillar and take out heart, type the heart crest spare parts, while entering and anticipating adoption incubate the type sprinkle into anticipate a form, while opening a mold, with the ball head pull and anticipate a pole sprinkle and note system and anticipate, then make use of and take out and push plank and release a plastics piece inside a heart,use spring coil and reset first while matching a mold, then carry on willing model a beginning next time.
摘要分析了香水盖外壳塑件的结构特点，叙述了该塑件成型工艺、注射模的结构和工作原理，其原理是：采用定距螺钉和弹簧进行二次分型，用斜导柱外侧抽芯，型芯顶出零件，进料时采用潜伏式浇口进料形式，当开模的时候，用球头拉料杆把浇注系统凝料顶出，然后利用型芯内抽推板推出塑件，合模时用弹簧先复位，然后进行下一次成型开始。
-
The design of the side core_pulling system and the slanted kicking block of the core and the improvement of the feeding gate and kicking system were mainly discussed.
介绍了上壳体注射模的结构，重点介绍了模具侧抽芯、型芯斜顶块设计及进料浇口和顶出机构的改
- 更多网络解释与进模口相关的网络解释 [注：此内容来源于网络，仅供参考]
-
die bush：进模口套(压铸模)
进模口,闸口 inlet | 进模口套(压铸模) die bush | 晶格,结晶格子 crystal lattice
-
wedge friction gear：楔槽进模口
楔形填隙料 wedge filler | 楔槽进模口 wedge friction gear | 楔闸阀 wedge gate
-
hone gate：喇叭形进模口,喇叭形浇口
喇叭浇管 trumpet | 喇叭形进模口,喇叭形浇口 hone gate | 蜡 wax
-
ingate：进模口
浸嘴(底浇式浇桶) immersion nozzle | 进模口 ingate | 进模口,闸口 inlet
-
ring gate：环形进模口
环秤(风量计) ring balance | 环形进模口 ring gate | 环形流道 ring runner
-
side step gate：分层进模口
分层浇口 side step gating | 分层进模口 side step gate | 分层精炼法 zone refining
-
steeped sprue：分级进模口
分级节(模砂) classifying screen | 分级进模口 steeped sprue | 分级进模口 step gate
-
gate area：浇口剖面积,进模口剖面积
浇口发暖剂 pouring gate feeding compound | 浇口剖面积,进模口剖面积 gate area | 浇口切断 gate cutting
-
gate area：进模口剖面积
浇斗嘴 lip | 进模口剖面积 gate area | 浇口切断 gate cutting
-
form board：进模口板
forming成型(抽凸,冲凸) | form board 进模口板 | forming die成型模