- 更多网络例句与进位信号相关的网络例句 [注：此内容来源于网络，仅供参考]
-
A column counter increases a count value in increments of one in response to the carry signal.
列计数器响应进位信号，以增量1增加计数值。
-
The design of the device using NC Lathe CA6140 control, part of the main transmission system using AC spindle motor and graded by the pulley driven spindle gearbox, through the inverter and gearbox to achieve sub; Feed System used by stepper motor driven ball screw slowdown after campaign vertical feed system through a gear after the ball screw drive, in the horizontal feed system through two gear-driven ball screw; Tool to automatically transfer tool carrier (4-position), thus achieving automatic tool change; by MCS-51 series 8051 data to be dealt with. from the I / O interface stepper pulse output signal to control the feed rate and itineraries; In order to maintain the function of cutting thread, to the outer end of spindle or other appropriate location loaded pulse generator; Lathe will be transformed into Tailstock manually controlled electric Tailstock.
本设计利用数控装置对CA6140普通车床进行控制，主传动系统部分采用交流调频主轴电动机经带轮及分级齿轮变速箱驱动主轴，通过变频器和齿轮变速箱实现分段无级变速；进给系统采用步进电机通过减速后驱动滚珠丝杠运动，在纵向进给系统中通过一级齿轮减速后驱动滚珠丝杠，在横向进给系统中通过二级齿轮减速驱动滚珠丝杠；刀架改为自动转位刀架从而实现自动换刀；通过MCS-51系列8051单片机对数据进行计算处理，由I/O接口输出步进脉冲信号控制进给速度和行程；为了保持切削螺纹的功能，要在主轴外端或其它适当部位装上脉冲发生器；将车床的手动尾座改造成为可控电动尾座。
-
The design of the device using NC Lathe CA6240 control, part of the main transmission system using AC spindle motor and graded by the pulley driven spindle gearbox, through the inverter and gearbox to achieve sub; Feed System used by stepper motor driven ball screw slowdown after campaign vertical feed system through a gear after the ball screw drive, in the horizontal feed system through two gear-driven ball screw; Tool to automatically transfer tool carrier (4-position), thus achieving automatic tool change; by MCS-51 series 8051 data to be dealt with.
本设计利用数控装置对CA6240普通车床进行控制，主传动系统部分采用交流调频主轴电动机经带轮及分级齿轮变速箱驱动主轴，通过变频器和齿轮变速箱实现分段无级变速；进给系统采用步进电机通过减速后驱动滚珠丝杠运动，在纵向进给系统中通过一级齿轮减速后驱动滚珠丝杠，在横向进给系统中通过二级齿轮减速驱动滚珠丝杠；刀架改为自动转位刀架从而实现自动换刀；通过MCS-51系列8051单片机对数据进行计算处理，由I/O接口输出步进脉冲信号控制进给速度和行程；为了保持切削螺纹的功能，要在主轴外端或其它适当部位装上脉冲发生器；将车床的手动尾座改造成为可控电动尾座。
-
Dismounts the electrically operated installment the box to cover and the wiring lid, penetrates the pilot wire cable and the holding wire from the coil in hole, the mortgage graph ticks the line cable core and the post the connection, afterwards withdraws from the mechanical spacing
3卸下电动装置的箱罩及接线盒盖，将控制线缆及信号线从进线孔穿入、按接线图将线缆芯和端子对号连接，之后退出机械限位
- 更多网络解释与进位信号相关的网络解释 [注：此内容来源于网络，仅供参考]
-
carry signal：进位信号
carry 进位 | carry signal 进位信号 | cartan decomposition 嘉当分解
-
carry signal terminal：进位信号终端
carry signal 进位信号 | carry signal terminal 进位信号终端 | carry skip method 跳越进位法
-
carry initiating signal：进位启动信号
进位指示器 carry indicator | 进位启动信号 carry initiating signal | 进位输入 carry input
-
carry clear signal：进位清除信号
进位电路 carry circuit | 进位清除信号 carry clear signal | 进位完成 carry complete
-
carry complete signal：进位完成信号
进位完成 carry complete | 进位完成信号 carry complete signal | 进位完成 carry completion
-
carry complete signal：进位结束信号,进位完成信号
carry-complete 进位完毕 | carry-complete signal 进位结束信号,进位完成信号 | carry-delay 进位迟延
-
carry complete signal：完全进位信号
完全进位信号 carry-complete signal | 卡特尔电话决定 carterfone decision | 笛卡儿坐标系统 Cartesian coordinate system
-
carry,partial：部分进位
carry,end-aroand端回进位 | carry,partial部分进位 | carry-completesignal完全进位信号
-
decadal signal：十进位信号
deca-newton | 十牛顿 | decadal signal | 十进位信号 | decade | 十进制,十进位
-
decadic signal：十进位信号
decadent wave 减幅波 | decadic signal 十进位信号 | decadienoic acid 癸二烯酸