轴向

词组短语

longitudinal direction

与轴向相关的网络例句 [注：此内容来源于网络，仅供参考]

The effect of tribology factors on bearing vibration is studied experimentally. AR model and WPT are used to processing the normal arid abnormal signals. The results are as follows:1. The vibration of ball bearings is caused by the tribology action of contact pairs of ball and ring races and has the essential of tribo-dynamics. Any factors affecting the tribology characteristics of contact pairs will affect vibration and noise of bearings consequently.2. Vibration characteristics of bearing keep almostly unchanged with the increasing of axial load expecting the increasing of nature frequencies. When radial load increasing with axial load unchanged, nature frequencies keep unchanged but some new vibration peaks appears in the spectrum.3. Vibration amplitudes are damped and nature frequency are enhanced with sufficient lubrication. Vibration and noise of bearings increase obviously and roar can happen and the contact surfaces scratch slightly under insufficient and unclean lubrication state. Bearing will be disabled in a few minutes without any lubrication.4. Bearing vibration is unstable under low speed. With the speed increasing, the vibration become stable and natural frequencies increase slightly but the amplitudes increase apparently.5. Bearing vibration can be excited only by some harmonics ofwaviness without lubrication and by all harmonics with lubrication based on the theoretical analysis.6. The nature frequencies of ball bearings decrease with the increasing sizes. When international clearance increasing, nature frequencies decrease in radial and increase in axial and angular and the amplitudes increase in radial and decrease in axial and angular. When the number of balls increasing, nature frequencies increase and amplitudes decrease. When the pitch diameter increasing, axial nature frequency increase and others nearly keep no change. When outer race groove curvature radius increasing, nature frequencies increase in radial and decrease in axial and angular and amplitudes keep no change in radial and increase in axial and angular. When inner race groove curvature radius increasing, nature frequencies decrease and amplitudes increase.7. The distortion in amplitude and frequency components of bearing vibration signals picked up by the present probe measurement method is founded and right conclusions cannot be achieved by the signals. When accelerometer is rigidly screwed with steel stud onto a flat outer surface of a ball bearing, vibration signal can be got without distortion and the reliability of research on bearing vibration is assured.8. AR model is suitable for large samples of bearing vibration signals, square root of length of samples can be used as the upper limitation of order determination and the FPE order selection criterion is effective. Many advantages of AR spectrum are founded over the classical based on FFT.9. Time-Frequency analysis is necessary for abnormal noise of ball bearings. WPT overcomes the principle shortcomings of STFT and proved to be a best tool to process the abnormal signals.

理论分析和试验研究表明： 1球轴承振动是钢球—滚道接触副中的各种摩擦学作用引起的，具有摩擦动力学的本质，任何对接触副的摩擦学特性有影响的因素都将对球轴承的振动和噪声特性产生影响； 2中心轴向载荷作用下，载荷增大使球轴承的固有振动频率升高，载荷越大同样的载荷增幅引起的频率升幅减小，足够大的中心轴向载荷作用下载荷的变化对球轴承振动的频率特性不会产生明显的影响； 3轴向和径向联合载荷作用下，径向载荷不大时球轴承振动的固有频率基本不变，但是可能引起变刚度激励的非线性振动，出现新的频峰，过大的径向载荷将使部分钢球脱离接触，使球轴承的振动和噪声呈现不稳定状态； 4润滑对球轴承的振动和噪声特性有重要的影响，良好的润滑对振动有明显的抑制作用，润滑不充分时，振动和噪声的水平会有明显增高，一定条件下还会激发接触副中的谐振，发出啸声，造成接触表面的伤害，无润滑干接触时，短时的运转就会损伤接触副表面，使振动和噪声迅速增大，并随时可能引发严重的磨损和卡滞失效；接触副润滑良好时，油膜的"刚化效应"使球轴承振动的固有频率有所提高，润滑剂中含有弥散性污浊时，振动的幅度总体升高，但弥散性污浊不会改变球轴承振动的频率特性；浙江大学博士学位论文：球轴承振动的研究 5低速时，球轴承振动的基本特征呈现不稳定状态，随着转速的提高，球轴承振动的频率特性趋于稳定，固有频率频峰升高； 6理论分析表明，干接触时钢球和滚道表面波纹度的某些谐波分量能激励球轴承的振动，振动的幅值与谐波幅值成正比，实际球轴承中钢球的分布不可能完全均匀，波纹度的激励作用会随时发生；润滑接触的分析表明，波纹度的任意谐波分量均能激励球轴承的振动； 7球轴承的几何和结构参数分析表明，球轴承尺寸越大，径向、轴向和角振动的固有频率越低；钢球中心圆直径增大，球轴承的径向和轴向振动的固有频率基本不变，角振动的固有频率有所上升，振动的幅频特性基本不变；径向游隙加大使球轴承的径向振动固有频率降低，轴向和角振动的固有频率有所升高，径向振动幅频特性的幅值升高，而轴向和角向降低；钢球的数量增多使球轴承振动的固有频率上升，幅频特性的幅值下降，径向振动的幅值下降最为明显；外圈沟曲率半径系数增大使球轴承径向振动的固有频率升高，轴向和角振动的固有频率降低，径向幅频特性基本不变，轴向和角向幅频特性幅值升高；内圈沟曲率半径系数增大使径向、轴向和角振动固有频率均下降，振动幅频特性的幅值均有升高； 8试验对比表明，传感器采用探针式安装时，由于探针接触副接触特性的影响，钡(量得到的球轴承振动信号有失真，采用专门设计和制作的试验球轴承，以固定式安装加速度计，首次测量得到了球轴承振动的真实信号，通过对振动信号的分析，验证了球轴承振动的理论模型； 9)基于时间序列分析的AR模型适用于大样本球轴承振动信号的分析，以样本长度的均方根值作定阶上界，FPE做判阶准则，给出的AR谱光滑，频率分辨率高，是球轴承振动分析的简便而可靠的手段； 10以时频域分析的小波包变换分析球轴承异音信号能够比较好地定位和聚焦异音发生的时间，时间间隔，频率范围，同样是球轴承振动分析的可靠的手段，可用作球轴承故障诊断技术。

Polynomial fitting was used to map out the pressure distribution curve of numerica...

与通过试验数据计算出的结果相比，数值模拟计算出来的轴向力相对误差在9%以内，而经验公式计算的轴向力相对误差为14%，采用数值模拟方法计算轴向力具有更高的精度，对多级离心泵轴向力平衡的研究具有指导意义。

The invention relates to a nut (10) comprising an outer body (16) with an axial passage (22), an inner body which can be movably placed in the passage along an axial direction and which is divided along said axial direction into at least two jaws (18, 20), each jaw bearing an inner thread segment (24) on its radial inner surface, first guiding means (26) located on the outer body, as well as second guiding means (30) located on the jaws and co-operating with the first guiding means so that the jaws are radially displaced towards the exterior when the outer body is displaced in the unscrewing direction relatively to the inner body et radially displaced towards the inside when the outer body is displaced in the screwing direction relatively to the inner body.

本发明涉及一种螺母(10)，它包括：一个带轴向通孔(22)的外体(16)；一个内体，位于通孔(22)中，可沿轴向移动，并且沿所述的轴向方向至少分成两个滑块(18、20)，它们各自在其径向的内表面上具有内螺纹部分(24)。在外体上有第一导向装置(26)，同样滑块上有第二导向装置(30)，第二导向装置与第一导向装置共同起作用，所以，当外体相对于内体沿旋松方向作相对滑移时，滑块径向地向外滑移，并且，如果外体相对于内体沿拧紧的方向滑移，则滑块径向地向内滑移。

In this paper, several methods are put forward, by which axial resolution of scan microscope could be improved. One is that detecting method of ordinary laser feedback is improved, the orthogonal polarized lights split by Wollaston prism are detected separately, comparing to the ordinary feedback, the axial resolution is improved about 2.9 times.

提出并实验研究了几种可以提高激光反馈扫描显微镜轴向分辨率的方法，一种方法是对常规激光反馈实验中的探测技术进行了改进，用渥拉斯顿棱镜把垂直偏振光分开探测，轴向分辨率可以提高约 2 9倍；另一种方法是用双频激光器中产生的偏振态相互垂直的o光和e光作为反馈光代替了传统的单一光的反馈，轴向分辨率被提高了约 2倍；第三种方法是用双频激光器中产生的o光或e光作为反馈光，轴向分辨率可以提高约 2 5倍。

The B and Q bands, the characteristic bands of the two metalloporphyrins, undergo bathochromic shift in some of the Lewis basic solvents. The spectral changes are thought to be due to the axial coordination of these solvents with vanadium in VOTPP and nickel in NiTPP. After axia...

结果表明，金属卟啉可以和一些Lewis碱性溶剂发生轴向配位作用，其特征紫外可见吸收峰发生红移；轴向配位作用与卟啉中心金属离子的外层d轨道电子数、碱性溶剂的供电子能力及其空间构造有关，VOTPP比NiTPP更容易和Lewis碱性溶剂发生轴向配位作用；碱性强、空间阻碍小的Lewis碱性溶剂易于与金属卟啉发生轴向配位作用。

This invention relates to an apparatus for testing permeability coefficient of low-permeability rock medium, which comprises a sensor, a temperature control box and a flowmeter both connected to the triaxial chamber with a gas injection port and a gas outlet on ends, a rigid press axle pressure and rigid press confining pressure system. Wherein, arranging an axial/lateral pad in the said chamber, and setting a horizontal strain gage chain and clamp.

本发明公开了一种低渗透岩石介质渗透系数测试仪，它由传感器、温控箱、刚性压力机轴压、刚性压力机围压系统构成，流量计与三轴室相连，温控箱与三轴室相连，在三轴室内装有轴向垫片和侧向垫片，在三轴室筒壁上装有横向应变计链子，在三轴室一端有注气口，另一端装有排气口，在三轴室上装有横向应变计夹子。

5Ns. The peak position of N band emission as well as the distinct emission region slightly moves towards the open end of the cylindrical cavity, and this does not happen to O band emission. Radiation transport efficiency of 6% is obtained for the φ400×1200um cylindrical cavity heated by x-ray source with radiation temperature of 118 eV.

从时间分辨的X光强度轴向空间分布来看，在较长时间（约1～1.5ns）内，O带X光在整个观测缝对应的轴向范围之内均有较大的辐射强度，在X光强度空间分布的变化过程中，其强度峰值的空间位置基本不变；而对N带X光，则只在较短时间（约0.5ns）内，在整个观测缝对应的轴向范围之内可观测到X光辐射，但只在靠近输运源约300μm的范围内有较强发射，在柱腔末端600～700μm范围之内的辐射则很弱，N带X光辐射轴向空间分布曲线的峰值位置在朝柱腔末端的方向移动，移动量大约为130～250μm。

The sliding gear assembly consists of sliding shaft, sliding gear and sliding clutch. The sliding shaft coaxial with the driving shaft has one end stretched into the axial hole on one end one the driving shaft and the other end supported on the front end casing; and the driving shaft is fixed axially onto the pedestal.

滑动齿轮组件由滑动轴、连接在滑动轴上滑动齿轮、连接在在滑动轴上的滑动离合器组成；滑动轴与传动轴同轴；滑动轴的一端的伸入在传动轴的一端沿轴向所开的孔内，另一端支撑在前端壳体上；传动轴在轴向被固定在底座上。

Therefore, for improving the accuracy of exceed slender axle on turning,must need to do with the lathe fixture and cutting tool for further improvement. In order to reached the requirements of precision machining,in machining process must use follower rest、flexible active thimble、space block and bracket etc fixture and assistive device.

超细长轴在车削加工中承受自身重力、切削力、高速旋转产生的离心力的作用，极容易出现振动与弯曲变形现象，增大轴的几何形状误差，而超细长轴的轴向尺寸较大，直径较小，热扩散性及刚性差，受切削热作用会在轴向发生线性膨胀，若在轴向的伸长量无法得到消除，轴将受迫弯曲，从而影响轴的精度。

The turbine comprises at least one radial or diagonal turbine stage (120) with radial or diagonal feed stream and axial exhaust flow and at least one axial turbine stage (121 - 125) with a axial feed steam and axial exhaust flow.

该涡轮机包括至少一个带有径向的或者对角线的入口和轴向的出口的径向的或者对角线的涡轮机级(120)和至少一个带有轴向的入口和轴向的出口的轴向涡轮机级(121-125)。

与轴向相关的网络解释 [注：此内容来源于网络，仅供参考]

axial field：轴向场

axial 轴向的,沿轴的 | axial field 轴向场 | axial search coil 轴向探察线图

axial symmetry：轴向对称

axial symmetric strain | 轴向对称应变 | axial symmetry | 轴向对称 | axial tension | 轴向拉力, 轴向拉伸

axial：轴向

3.轴向(Axial)荷重用斜角滚珠轴承之高速化(ULTAGE「HTAU型」)轴向(Axial)荷重用斜角滚珠轴承是车床的主轴中,最先开始使用的高刚性、耐荷重性的必要轴. 轴向(Axial)荷重用斜角滚珠轴承主要是和复列圆柱轴承合并使用,

axial load：轴向载重;轴向荷载

axial force 轴向力 | axial load 轴向载重;轴向荷载 | axial stress 轴向应力

axial load：轴压;轴向载重

axial force 轴向力 | axial load 轴压;轴向载重 | axial strain 轴向应变

axial thrust：轴向推力,轴向推力

axial tension | 轴向拉伸 | axial thrust | 轴向推力,轴向推力 | axial thrust load | 轴向分力,轴向平面

axial clearance：轴向间隙,轴向净空

"轴向间隙","axial clearance" | "轴向间隙,轴向净空","axial clearance" | "轴流压缩机","axial compressor"

Axis Constraints：轴向约束

Axis轴;轴向;坐标轴 | Axis Constraints轴向约束 | Axis Scaling轴向比率

axial tensile force：轴向拉力,轴向张力

axial tag terminal 轴端 | axial tensile force 轴向拉力,轴向张力 | axial tension 轴向拉力

shaft end play：轴的轴向间隙

shaft end;轴端 | shaft end play;轴的轴向间隙 | shaft end play shim;轴的轴向间隙垫片