车门

词组短语

car door · side doors of a motor vehicle or carriage

与车门相关的网络例句 [注：此内容来源于网络，仅供参考]

And measure the separation between the exterior edge of the doorframe and the interior of the door along the perimeter of the door.

5.11.3.4如上述保持施加负载的设备的位置，测量门框外部边缘与车门内侧之间沿著车门周围的分离距离。

In addition, because two cars in level differences seven series doors more than three series of doors increased in Mifengquan to it become possible dust capacity considerably, so a gatepost also in the structure corresponding measures to be taken.

此外，因为两车在级别上的差异，7系列车门比3系列车门多增加了一道密封圈，使其隔噪隔尘能力大为提高，所以，A门柱在结构上也需采取相应的措施。

Interchange station for the Tsuen Wan Line, Tung Chung Line or Airport Express.

左边既车门将会打开。下一站：坑口。左边的车门将会打开。

Other differences include an AMG spoiler lip on the boot lid, a roller blind for rear window, Nappa leather appointments for the seats, the top section of the dashboard, the beltlines, the door armrests as well as the centre console and door centre panels.

其他分歧包括AMG的扰流唇对尾部的箱盖，一个卷帘的后窗，纳帕皮革任命的席位，顶部的仪表板， beltlines ，车门扶手，以及中控台面板和车门中心。

In order to improve the sinkage stiffness of automobile door ,different improved designs are put forward.

针对某车门下沉刚度问题，提出了提高车门下沉刚度的多种改进设计方案，通过有限元方法对各改进方案进行了变形量和应力计算，经比较分析，得到可行的改进方案。

Include the design of the outer turning service door and the the swing door.

本文为兼容残疾轮椅中型客车车门设计，包括外摆式乘客门和旋转式车门的设计。

The deformation conditions of car door outer board in X and Y direction before/after the weather strip assembly are analyzed.

车门在安装密封条前后在X向和Y向存在着较大的变形，说明车门的刚度存在着薄弱环节。

The forces that act on the door by the weather strip are simulated and analyzed, and results of calculation fully explain the problem of large door closing force.

然后，对实测车门的受力变形、车门装配误差进行有限元分析。

An anonymous wit scratched those lines on the side of a junked car door and lugged it to a trail near my home in Northern California.

不具名的这段话被刻在一扇废弃的车门上，车门被抛弃在加里佛尼亚北部我家附近的一条小径上。

A drawing die,a trimming and piercing die and a flanging and restriking die for the precision shaping of the part were designed by using AutoCAD and UGII.

在详细分析车门内板结构及工艺特点的基础上，确定零件的成形工序，以AutoCAD及UGII为辅助工具，设计出车门内板成形所需的拉深模、修边冲孔模和翻边整形模，不仅保证了加工精度，同时也缩短了生产周期，降低了成本。

与车门相关的网络解释 [注：此内容来源于网络，仅供参考]

Door Armrest：车门扶手

安全带 Seat Belt | 车门扶手 Door Armrest | 车门把手 Door Handle

HINGE, FRONT DOOR：前车门铰链

前车门焊接总成 FRONT DOOR SHELL | 前车门铰链 HINGE, FRONT DOOR | 后视镜 REAR VISION MIRROR

FRONT DOOR SHELL：前车门焊接总成

前车门开度限位器 OPENING STOPPER, FRONT DOOR | 前车门焊接总成 FRONT DOOR SHELL | 前车门铰链 HINGE, FRONT DOOR

Door guttering：车门沟槽

Door gear 车门传动装置 | Door guttering 车门沟槽 | Door leaf bottom inside face 车门底部的内表面

LDCM Left Door Control Module：左车门控制模块

LDCL Left Door Closed Locking 左车门关闭锁止 | LDCM Left Door Control Module 左车门控制模块 | LED Light Emitting Diode 发光二极管

STVL Door satellite, front left：左前车门卫星式控制单元

SSH Rear seat satellite 后部座椅卫星式控制单元 | STVL Door satellite, front left 左前车门卫星式控制单元 | STVR Door satellite, front right 右前车门卫星式控制单元

DEADLOCKING ACTIVE：车门自上锁功能启动 车门未关好,或后备箱未关好. 中央显示屏伴随显示

HANDBRAKE ON 忘记松开手刹,一般新手或疏忽容易引起此故障. | DEADLOCKING ACTIVE 车门自上锁功能启动,车门未关好,或后备箱未关好. 中央显示屏伴随显示. | ABS FAULT ABS系统故障

door key：车门钥匙

door hinge;车门绞链 | door key;车门钥匙 | door latch;车门碰锁

door track：车门导轨

Door stop 车门止挡 | Door track 车门导轨 | Door trolley roller 车门滚轮

Door gauge：车门侧隙规

Door control 车门控制装置 | Door gauge 车门侧隙规 | Door gear 车门传动装置