起边皱

基本解释 (translations)

frill

与起边皱相关的网络例句 [注：此内容来源于网络，仅供参考]

And further because its line is thick, the grain deep, smooth, the corrugation, does not hemstitch, the entire cloth cover forms the innumerable nature massage spot, plays unexpectedly to the human body skin guarantees the healthy skin role, therefore is the pure natural green health products.

又因其线条粗、纹深、平整、不起皱、不卷边，整个布面形成无数个自然按摩点，对人体皮肤起到意想不到的保健美肤作用，所以是纯正的天然绿色保健产品。

All focussed their attention at the scene exhibited, a group of savage women in striped loincloths, squatted, blinking, suckling, frowning, sleeping amid a swarm of infants (there must have been quite a score of them) outside some primitive shanties of osier.

99大家都把注意力集中在出示给他们的图片上：一群未开化的妇女腰间缠着条纹布，蹲在柳条编成的原始窝棚前面，在成群的娃娃簇拥下，边眨巴眼睛，让娃娃叼着乳房，边皱起眉头，打着盹儿。

Emperor sees an edge by the side of Bede pursy brows, say to that fellow: I did not see you did the thing with particularly good what, but you also had not done what evildoing.

圣彼德边看边皱起眉头，对那家伙说：我没看到你做了什么特别好的事情，但你也没做过什么坏事。

These two defects were suppressed when polyurethane elastic cushions and steel paddings were used between the titanium alloy retiary sheet and the press punch with the blankholder device in the forming technology mode, and the 3D curved surface of prosthesis with good quality can be acquired.

模拟结果表明：采用前两种成形工艺得到的钛合金颅骨修复体表面出现压痕或起皱缺陷，采用在基本体和钛合金网板之间放置聚氨酯弹性垫和钢质垫板并使用压边圈这种成形工艺时，可以抑制压痕和起皱的产生，获得良好的成形效果。

Cockling: The puckered effect produced when printing sheets of paper having wavy or tight edges.

起皱：用带有浪形纸边或弓形纸边的纸张施印，起皱情况就会发生。

If the blank is wrinkling on the blank holder surface, the cause is most likely one of four factors: insufficient blank holder force; a poor fit between the die face and blank holder surface; an equalizer block that is holding the die face apart from the blank holder surface; or severe blank holder deflection.

如果板料在压边面上起皱，绝大多数起因是后面四个因素之一：不充分的压边力；凹模和压边圈表面不良的匹配；凹模和压边圈间的平衡块；或者是压边圈的严重变形。

If the blank is wrinkling on the blank holder surface, the cause is most likely one of four factors: insufficient blank holder force; a poor fit between the die face and blank holder surface; an equalizer block that is holding the die face apart from the blank holder surface; or severe blank holder deflection.

如果展开平板在压边圈面上起皱，绝大多数起因是后面四个因素之一：不充分的压边力；凹模和压边圈表面不良的匹配；凹模和压边圈表面间的平衡块；压边圈的变形。

If the blank is wrinkling on the blank holder surface, the cause is most likely one of four factors: insufficient blank holder force; a poor fit between the die face and blank holder surface; an equalizer block that is holding the die face apart from the blank holder surface; or severe blank holder deflection.

褶皱起因于不充分的拉伸或失去控制的压缩变形。如果板料在压边面上起皱，绝大多数起因是后面四个因素之一：不充分的压边力；凹模和压边圈表面不良的匹配；凹模和压边圈间的平衡块；或者是压边圈的严重变形。

In addition, the blank holding force that is required to avoid wrinkle and rupture during conical part deep drawing is researched. The necessity of reasonable blank holding force in pressing is expounded. From the view of mechanical analysis, the wrinkle critical condition of side-wall is derived for the first time by the stress state of side-wall, the main deformation region on blank. According to the critical condition of plastic instability for flange, side--wall, corner of punch on blank, The blank holding force in conical part deep drawing is divided into four different regions within its forming figure. The basic principle of reasonable blank holding force during stamping is summarized and provided. The mathematical model of reasonable blank holding force that avoids the wrinkle and rupture is established and verified by the finite element numerical simulation and the grid experiment method. The result shows that it is accurate and reliable.

此外，本文还研究了圆锥形件拉深成形过程中，随着拉深变形过程的进行，毛坯为避免产生起皱、破坏缺陷而对压边力的需求情况，阐明了圆锥形件拉深成形过程中压边力合理变化的必要性；由毛坯主要变形区悬空锥壁部分的受力变形情况，从力学分析的角度，首次推导得出了圆锥形零件悬空锥壁起皱失稳的临界条件；并根据主要变形区法兰、悬空锥壁及凸模圆角部分的塑性失稳临界条件，在其成形范围图中，将圆锥形件成形过程中的压边力划分为四个区域；总结并提出了圆锥形件成形过程中压边力合理变化的基本原则；建立了防止起皱、破坏缺陷产生的压边力合理变化的数学模式，并得到了有限元数值模拟及网格实验法的验证，证实了理论分析结果的正确性和可靠性。

Lotus Leaf contexts it business card printing and membership card making misregister or wrinkling, see double fault, the most common is the business card printing and membership card making wrinkle.

荷叶边也容易造成制卡和会员卡制作起皱、套印不准或重影故障，最常见就是制卡和会员卡制作起皱故障。

与起边皱相关的网络解释 [注：此内容来源于网络，仅供参考]

Frilled：有褶边的 (形)

frill 折成皱边; 起边皱 (动) | frilled 有褶边的 (形) | frilling 皱边 (名)

ruffler：扰乱的人

ruffled 褶饰边的 | ruffler 扰乱的人 | ruffly 起皱的

crimpness：蜷曲,蜷缩

压紧钳,折波钳,卷缩机,卷边机 crimper | 蜷曲,蜷缩 crimpness | 皱,缩,波皱,使皱,使缩,起皱缩卷 crinkle

crisping：匀边

crisp | 卷缩的,起皱的,起波纹的 | crisping | 匀边 | crisscross motion | 交错运动

frigorific：致冷的; 冰冻的 (形)

frigidly 寒冷地; 冷淡地 (副) | frigorific 致冷的; 冰冻的 (形) | frill 折成皱边; 起边皱 (动)