- 更多网络例句与负载电压相关的网络例句 [注：此内容来源于网络，仅供参考]
-
17 Output smoothing Because a bleeder sets a minimum current drain, the regulation of the circuit, defined as percentage voltage change from minimum to maximum load, is improved.
由于分压器设置了最小漏电流，电路的调整定义成最小负载到最大负载电压变化的百分比。
-
Because a bulk smoothing capacitor is usually installed on the DC side of many AC to DC converters, the characteristics of harmonic loads will be influenced by this capacitor. Nowadays, shunt active power filters can't reduce harmonics effectively for this voltage type harmonic-producing load. Therefore, a series active power filter is designed to meet the requirements of voltage-sourced harmonic loads. Both source current and load voltage are detected in order to reach the compensation voltage for the SAPF.
由於许多交直流电源转换器均在直流端并联一直流电容以作为稳压之用，此大电容将造成负载谐波特性的改变；此类谐波源负载，如果使用现今常见的并联型主动式电力滤波器并不能很有效解决此类谐波问题；因此本文将采用串联型主动式电力滤波器，并配合同时量测电源电流及负载电压的混合式控制模式，即可有效解决此类谐波问题。
-
A state variable feedback based system control approach, which indirectly controls load voltage by means of controlling the supply current, is proposed, thus the problem that the undamped DC transient component of supply current, which is caused by the linking inductance between power supply and power loads under PI control mode, is solved.
分析了仅由1套逆变器构成的并联型综合电能质量调节器的结构特点和控制目标，提出了一种基于状态变量反馈的系统控制方法，通过控制电源电流来间接控制负载电压，很好地解决了常规比例–积分控制时电源和负载间的连接电感所导致的供电电流直流暂态分量不衰减的问题。
-
In this paper, quantitative analysis on exchange between inverter unit of DVR and grid is made when voltage temporarily drops. Then it studys detailedly the relationship of output voltage and power amang inverter unit of DVR ,grid and load.Finally Matlab simulations of all the compensation method are made.
本文定量分析计算电网电压暂降时DVR 逆变单元与电网的功率交换情况，详细研究逆变单元在各种补偿策略下的输出电压和有功功率与故障前后电网电压、负载电压和参考相量的具体关系，最后通过Matlab 仿真研究各补偿方法。
-
Then it studys detailedly the relationship of output voltage and power amang inverter unit of DVR ,grid and load.Finally Matlab simulations of all the compensation method are made.
本文定量分析计算电网电压暂降时DVR 逆变单元与电网的功率交换情况，详细研究逆变单元在各种补偿策略下的输出电压和有功功率与故障前后电网电压、负载电压和参考相量的具体关系，最后通过Matlab 仿真研究各补偿方法。
-
Based on the rated voltage that the normally working load needs, this paper discusses that the load current is restricted by controlling the secondary current of series transformer so as to meet the invariableness of the rated voltage.
在负载正常工作时所需的额定电压的基础上，该文讨论通过控制串联变压器二次侧工作电流来约束负载电流，从而使负载电压恒定。
-
The filter only needs to detect the three-phase electrical power's current, load voltage and DC voltage. It eliminates the multipliers, the calculating of harmonicas and the reactive current.
该滤波器只需检测三相电网电流、负载电压和直流侧电容电压，不需要乘法器，省去了谐波和无功电流的计算。
-
He square of the r.m.s. load voltage represents the power dissipated in a purely resisT
负载电压的平方值表明了功率消耗为阻性负载的持续温度。
-
The square of the r.m.s. load voltage represents the power dissipated in a purely
负载电压的平方值表明了功率消耗为阻性负载的持续温度。
-
The square of the r.m.s. load voltage represents the power dissipated in a purely resistive load whose resistance remains
负载电压的平方值表明了功率消耗为阻性负载的持续温度。
- 更多网络解释与负载电压相关的网络解释 [注：此内容来源于网络，仅供参考]
-
dropout voltage：跌落电压
为此,它提供负载电流以保证输出电压稳定:NPN,LDO和准LDO在电性能参数上的最大区别是:跌落电压(Dropout Voltage)和地脚电流(Ground Pin Current). 跌落电压前文已经论述. 为了便于分析,我们定义地脚电流为Ignd (参见图4),并忽略了IC到地的小偏置电流.
-
dummy load：假负载
传统蓄电池组容量试验是以整组电池切离系统,并将假负载(Dummy Load)接在电池上,调整负载大小,使其负载维持电流为八或十小时率电流放电,然後以整组中最先到达放电终止电压(Final Voltage)之某一蓄电池(容量落後电池)的放电时间与电流值来估算其容量.
-
voltage fluctuation：电压波动
这些设备常做周期性或随机性的工作,并且分布在多条生产线上,每条生产线又有多部设备,由於这类负载用电量变化相当剧烈,从全载至空载来回变化,所以在其邻近之汇流排上,就会发生程度不一之电压波动(voltage fluctuation)现象,其波动幅度大小,
-
matched load：匹配负载
匹配 Matching | 匹配负载 matched load | 匹配负载电压 matched-load voltage
-
open-circuit voltage：开路电压
说明:指电池的平衡电势或可逆电势,也即可逆电池的开路电势. 此时参与电池反应的物质都处在平衡态. 如果电池不是可逆的,它的开路电势就不能称为电动势. 开路电势或开路电压(open circuit voltage)是指电池无负载时或不能外电流时的电势.
-
overpower protection：过功率保护[装置],过负载保护
"overpotential test ","过电压试验" | "overpower protection ","过功率保护[装置],过负载保护" | "overpower relay ","过负载继电器"
-
reference voltage：参考电压
最大负载电流CM8500不仅具有快速提供电流(Source Current)的功能,更具备快速汲入电流(SinkCurrent)的功能,它可供应3A汲入(Sink)或提供(Source)电流以支援DDR SDRAM记忆体模组所需的终端电压(Termination Voltage)和参考电压(Reference Voltage).
-
RL：负载电阻
定义了描述静态光学双稳态特性的7个基本参数,并分析了负载电阻(RL)和电源电压(V0)对这些参数的影响,理论分析结果与实测结果相一致,所得出的结论适用于由负阻特性产生双稳态特性的所有情况1.
-
Voltage threshold：电压阈值
还有一些参数建立了输入信号的安全限制,以及代表逻辑1和0的电压阈值(voltage threshold)等. 阈值电压限定了输入电压的大小,使器件按正常功能运行,而不会出现把逻辑1视为逻辑0的现象. 这里还有对输出驱动能力的限制,使用时请保证器件的输出负载不能超出额定值,
-
voltage：控制电压
因为是控制电压(Voltage)与频率(Frequency)之比,称为U/f控制. 恒定U/f控制存在的主要问题是低速性能较差,转速极低时,电磁转矩无法克服较大的静摩擦力,不能恰当的调整电动机的转矩补偿和适应负载转矩的变化;其次是无法准确的控制电动机的实际转速.