调整螺母

词组短语

adjusting nut

与调整螺母相关的网络例句 [注：此内容来源于网络，仅供参考]

The tripping and calibrating principle of the MCCB was introduced.The hardware and software design of the intelligent testing system was expounded.The screw adjusting mechanism along with the laser positioning technology can precisely locate the screw on the bimetallic strip of the MCCB and complete the screw simultaneous integration when being electrified.

介绍了塑料外壳式断路器的脱扣原理及校验方法，详述了MCCB智能测试系统的软、硬件设计，系统中所研制的一体化螺钉螺母调整机构结合激光定位技术，实现了对MCCB双金属片上螺钉螺母中心的精确定位及在通电过程中对螺钉螺母进行同步一体化调整。

Planet reduction shown in figure 6. Loose nut 6 "nut + washer + anti-loose nut". The explored view is Adjust torque 350~400N.m, rotate hub 13 at the same time. 5 and a radial force F=70N crease, hub can rotate free. Then fix lock washer into nut 6, fasten loose nut with torque 400N.m and make spacer control 0.05~0.15mm.

调整时，用 350~400N.m 力矩旋紧螺母 6，同时转动轮毂 13，使两轴承处于正确位置，然后，稍旋松螺母 6，在轮辋螺栓处施加一个切向力 F=55N.m，此时轮毂应能自由转动，然后装上止动垫片 5，将其卡爪折入螺母 6 的防转槽内，再用 400N.m 的力矩旋紧防松螺母，使轴向间隙控制在 0.05～0.15mm 之间。

Impeller with static balance is fixed onto the shaft by the sleeve and the sleeve nuts on the two sides. Its axial position may be adjusted through sleeve nut.

经过静平衡校验的叶轮，用轴套和两边的轴套螺母固定在轴上，其轴向位置可通过轴套螺母进行调整。

The shock bodies are threaded for quick changes to the ride height using a knurled purple-anodized adjustment nut, and the upper shock bladder helps keep the oil clean and rebound levels consistent.

休克机构线程快速的变化，向驾驶高度利用技术特性紫色-阳极氧化的调整螺母，与上层休克膀胱有助于保持清洁，石油和反弹，各级一致的。

These new adjusting nuts are made from Nylon and replace the previous aluminium nut with plastic insert which will not only makes assembly easier, it also reduces unsprung weight.

调整螺母为契机，球这些新的调整，坚果是由尼龙，并取代以往的铝螺母与塑料插入这将不仅使大会更容易，这也减少了unsprung重量。

It's suitable free stroke is so adjusted that front end of foot brake pedal goes down 25 mm before brake begins to function.The free stroke can be adjusted by adjusting the butterfly nut on rear brake rod.

It的合适的自由行程是如此调整是前端脚刹车踏板关闭25毫米制动前开始免费中风函数可以进行调整，通过调整螺母上的蝴蝶后轮制动杆。

To match the rest of the car, the spring adjust nut, upper cap, lower cap and shock end balls are anodized in the bright purple colour found on the rest of the car.

为了配合其余的汽车，春季调整螺母，上上限，上限降低及休克，最后球是在阳极氧化的光明紫色发现，对其余的车。

Adjusting the packing 1 Pump packing (1) continue to hand tighten the squeeze cap nut;(2) after opening the pump, adjust the gland nut, this time to allow a little more leakage;(3) slowly tighten the squeeze cap nut, gradually reduce the leak until the leak to an acceptable level;(4) If the disclosure of a sudden stop, should be back to tighten the gland nut, packing re-adjustment in order to prevent overheating;(5) adjust the leakage rate can reach a steady state.

泵用盘根（1）继续用手拧紧压盖螺母；（2）开泵后，调整压盖螺母，此时截止阀允许有稍多的泄漏；（3）缓慢地拧紧压盖螺母，逐渐减少泄漏，直到泄漏达到可接受的程度；（4）如果泄露突然停止，应回拧压盖螺母，重新调节以防止盘根过热；（5）调节泄漏率达到一个稳定状态即可。

Unscrew the locking nuts on the release lever, meanwhile unscrew the adjusting nuts using a spanner, while doing that measure the gaps between the release levers and bearings by means of feeler gauge, until the gap reads 0.3-0.5mm. Repeat it for three release levers, their gaps should be the same, after that screw up the locking nuts, and check it to make sure.

b、旋松分离杠杆上的锁紧螺母，一面用扳手转动调节螺母，一面用厚薄规测量分离杠杆与分离轴承之间的间隙，直到间隙为0.3-0.5毫米为止，三只分离杠杆依次都调整好，再将锁紧螺母锁紧，然后复查一遍。

B. Unscrew the locking nuts on the release lever, meanwhile unscrew the adjusting nuts using a spanner, while doing that measure the gaps between the release levers and bearings by means of feeler gauge, until the gap reads 0.3-0.5mm.

b、旋松分离杠杆上的锁紧螺母，一面用扳手转动调节螺母，一面用厚薄规测量分离杠杆与分离轴承之间的间隙，直到间隙为0.3-0.5毫米为止，三只分离杠杆依次都调整好，再将锁紧螺母锁紧，然后复查一遍

与调整螺母相关的网络解释 [注：此内容来源于网络，仅供参考]

adjusting pin：调整销

adjusting nut lock;调整螺母锁定装置[锁片] | adjusting pin;调整销 | adjusting plate;调整板

Adjusting nut：调整螺母

Adjusting lever 调整杆 | Adjusting nut 调整螺母 | Adjusting shim 调整垫片

Adjusting leer：调整杆

Adjusting hand wheel 调整手轮 | Adjusting leer 调整杆 | Adjusting nut 调整螺母

Adjusting shim：调整垫片

Adjusting nut 调整螺母 | Adjusting shim 调整垫片 | Adjusting spring 调整弹簧

washered nut：附有垫圈的螺母

washered adjusting nut;附有垫圈的调整螺母 | washered nut;附有垫圈的螺母 | washing fluid;清洗液

washered adjusting nut：附有垫圈的调整螺母

washer thickness;垫圈厚度 | washered adjusting nut;附有垫圈的调整螺母 | washered nut;附有垫圈的螺母

rating nut：调整螺母

rating测定、评价、定额、额定值、分等级 | rating nut调整螺母 | ratio flow control比例流量控制

spring adjustment nut：弹簧调整螺母

3 spring adjustment bolt 弹簧调整螺栓 | 4 spring adjustment nut 弹簧调整螺母 | 5 flush connection port 冲洗液连通孔

diff. bearing：差速器轴承调整螺母

diff. bearing 差速器轴承调整螺母 | Adjustment system 调节装置 | Administration and Registration Division 管理科

adjuster, diff. bearing：差速器轴承调整螺母

adjuster washer 调整棘片 | adjuster diff. bearing 差速器轴承调整螺母 | Adjustment system 调节装置