- 更多网络例句与装配螺钉相关的网络例句 [注：此内容来源于网络，仅供参考]
-
Before assembling the ball valve seat sealing surface and be equipped with decent research, and then placed in the closed position the sphere, the installation of left valve, adjusting the gasket, tighten the screws, static pressure irrigation does not leak, this valve can be guaranteed under the seal test seal.
装配前阀座密封面与球体面应配研，然后将球体置于关闭位置，安装左阀体，调整垫片，拧紧螺钉，静压灌水不漏，则此阀在密封试验下即可保证密封。
-
3 In the mounting or supporting of small, fragile insulating parts, screws or other fastenings should not be tight enough to cause cracking or breaking of these parts with expansion and contraction.
14.3在装配或支撑小而易脆的绝缘件时，螺钉和其它紧固件不要装得太紧以致于这些绝缘件的收缩或扩展而破裂。
-
To cooperate with new and old parts: although standard zero, components, but in between interchangeable in assembly parts, and to make the optimal coordination between trim, still needs a lot of work, such as the gear and rack, boring if after removal of gear various performance indicators are used by detecting without the need to change, and to replace worn rack, rack and rack positioning pin hole on installation bolt holes and should be first, reoccupy hand crossed positioning drills and tapered reamer to match the drill and match hinge, and after the installation of new and old super-modulus gear mesh clearance to achieve technical standards, this work takes about one day.
。新，旧零部件重新配合过程：尽管标准零，部件间具有互换性，但在装配中，要使新旧零部件间的配合达到最佳状态，仍需大量的修整工作，如镗床的齿轮与齿条，若拆卸后齿轮的各项性能指标经检测尚能使用不需更换，而齿条磨损严重需更换，那么齿条及齿条安装面上的定位销孔和定位螺钉孔就需先划线定位，再用手电钻及锥形铰刀重新配钻和配铰，且新齿条安装完毕后与旧齿轮的啮合间隙需达到技术要求的标准，此项工作需时约一天。
-
To cooperate with new and old parts: although standard zero, components, but in between interchangeable in assembly parts, and to make the optimal coordination between trim, still needs a lot of work, such as the gear and rack, boring if after removal of gear various performance indicators are used by detecting without the need to change, and to replace worn rack, rack and rack positioning pin hole on installation bolt holes and should be first, reoccupy hand crossed positioning drills and tapered reamer to match the drill and match hinge, and after the installation of new and old super-modulus gear mesh clearance to achieve technical standards, this work takes about one day.
。新，旧零部件重新配合过程：尽管标准零，部件间具有互换性，但在装配中，要使新旧零部件间旳配合达到最佳状态，仍需大量旳修整工作，如镗床旳齿轮与齿条，若拆卸后齿轮旳各项性能指标经检测尚能使用不需更换，而齿条磨损厉害需更换，那么齿条嘉逸条安装面上旳定位销孔和定位螺钉孔就需先划线定位，再用手电钻及锥形铰刀重新配钻和配铰，且新齿条安装完毕后与旧齿轮旳啮合间隙需达到技术要求旳标准，此项工作需时约─天。
-
Relations in accordance with the machines to install the rack assembly components, rack location placed slightly tight after all the connecting screws, adjust the rack so that the eight rack Thread smoothly cylindrical pin penetration, fastening screw connection .
按照机器的装配关系先安装机架组件，机架位置放好后稍带紧所有的联接螺丝，调整机架使机架上的八个内螺纹圆柱销钉都能顺利穿入，紧固连接螺钉。
-
Seal leak link Office Reason: 1, ring rolling strict 2, seals and body welding, surfacing of poor quality; 3, ring connecting thread, screw, loop loose; 4, ring connection and corrosion.
堆焊处无法补焊时应清除原堆焊和加工； 3、卸下螺钉、压圈清洗，更换损坏的部件，研磨密封与连接座密合面，重新装配。
- 更多网络解释与装配螺钉相关的网络解释 [注：此内容来源于网络，仅供参考]
-
blind hole：盲孔
装配为副本 可以利用"盲孔 盲孔"(Blind hole) 或直孔来放置垃圾钉.当垃圾盘组件包含螺钉时,会使用螺纹 盲孔孔. 另请参见 关于元件 关于螺钉 螺钉将两个元件连接在一起.带肩螺钉与碰锁很相似,用于控制板的移动.单击"EMX">"螺螺钉"(Screw),
-
dowel pin：定位销
单击"定位销 定位销"(Dowel Pin) > "...装配自动螺钉 装配自动螺钉"(...assemble Autoscrews).选择底部夹持板装配新销钉. 定位销 装配自动螺钉 要重定义预定义的定位销设置,请在零件模式下再次单击"定位销 > "...预定义 定位销" 预定义".EMX 将识别这些参数,
-
Rift saw：裂木锯
rift-over height 举过高度 | rift-saw 裂木锯 | rigging screw 装配螺钉
-
rigging screw：装配螺钉
rigging screw 松紧螺旋扣 | rigging screw 装配螺钉 | rigging shop 索具车间
-
right and left nut：左右纹螺母
rigging screw 装配螺钉 | right and left nut 左右纹螺母 | right angle 直角
-
mountings：零件 配件
mountingring 安装环 装配环 | mountings 零件 配件 | mountingscrew 安装螺钉