被加工

基本解释 (translations)

work

与被加工相关的网络例句 [注：此内容来源于网络，仅供参考]

Note that my anti-inflammatory diet emphasizes less-refined, less-processed foods with a low glycemic load including such whole grains as brown rice and bulgur wheat, in which the grain is intact or cracked into large pieces.Andrew Weil, M.D.

请注意我的饮食安排是有没有刺激作用的，强调食用提炼、加工程度低和生糖负荷低的全谷类食物，像糙米和碾碎的小麦，因为这些食物都是未经加工的或是被加工成大块大块的。

Solid carbide tungsten fishtail drill is suitable for pcb flexible foil clad laminate,used for target machine drilling,the features of pcb fishtail drill are thin and flexible plate,it's structure and cutting methods are different with normal pcb drill bits.its two main cutting edge is concave and formed 100degree angle,in order to distinguish with PCB drill,named fishtail drill.fishtail drill cuts beginning of circular drill.concave along the main cutting edge to cut,chip is just two much fine filament.cuttingis falling off naturally,in order to be processed without burrformation by pcb surface.

整体硬质合金鱼尾钻适合印制电路板行业加工挠性覆箔板，为打靶机钻孔用。鱼尾钻所加工的印制电路板特性是薄板、带柔性、这样就决定了它的结构和切削方式与一般PCB钻不一样，它的两主切削刃是内凹的，两主切削刃形成100度的夹角，为了与PCB钻区别，就叫它鱼尾名。鱼尾钻切削时从我圆处钻尖开始，沿着内凹的主切削刃切削，切屑只是两条极细丝状切削，整个切削自然剥落，从而被加工印制板表面平整无毛刺。

Single screw extruder is often used for polymer mixing, the effect of which is critical to the quality of the final product.

单螺杆挤出机经常被用于聚合物的混炼加工过程，对被加工的制品的质量有很大的决定作用。

TH-904 is used as chelant in papermaking coating, building coating, concrete retarder, water reducer, woven and dyeing. Its performance can reach to that of SN-5040. Adding TH-904 to slurry during grinding process of bolus alba, lime carbonate, pottery clay, titanium pigment, French chalk, barium sulfate, coal-water slurry, etc., the viscosity can be largely reduced and the dispersed slurry is stable.

TH-904水性分散剂广泛用做造纸涂料及建筑涂料的分散剂、混凝土缓凝剂、减水剂以及纺织印染等行业作螯合分散剂，性能达到SN-5040水平，在高岭土、碳酸钙、陶土、钛白粉、滑石粉、硫酸钡、水煤浆及水泥等浆料的研磨加工过程中加入TH-904分散剂能极大地降低被加工物料的粘度，便于物料的加工，且分散后浆料粘度稳定。

According to the working procedure chart of theZH1105W diesel engine's gear cap analysis workpiece's precision, the surface roughness, thespecification, the processing spot size, the shape structure,material degree of hardness, the work piece rigidity and thedifferent of the components batch size to definite technique andtechnological process, determine aggregatemachine-tool's overall plan. Consider to theirregularity components but have high accuracy holes to beprocessing. So,"two holes at aface" is the best localization plan.

根据ZH1105W柴油机齿轮室盖的工序图分析其精度、表面粗糙度、技术要求、加工部位尺寸、形状结构、材料硬度、工件刚性及零件的批量的大小不同，确定被加工零件工艺方法和工艺过程，确定该组合机床的总体设计方案；考虑该零件表面结构的不规则性但有较高精度的孔需要加工，定位基准选择&一面双孔&是最佳的方法。

On the basis of previously research, this paper re-probe into the mechanism of electro-chemist mechanical manufacturing process, making the rational technological parameter, and developing the manufacturing equipment. Through a lot of technology tests, get a lot of labratory data, accordingly, researched the surface feature of the electro-chemist manufacturing process, and deeply discussed its influence on the work piece feature. The last result is that: the electro-chemist mechanical manufacturing process can reduce the low-frequency component significantly, but on high-frequency component, it has little influence, having obviously positive pole flat effect. After manufacture, the tip parts on the surface of the work piece is cut off, there is micro "high land" shape, the parameter for surface roughness is reduced a lot, the surface outline of the work piece is negative, the bearing length rate is cliffy. Also the surface quality of the work piece is improved. This can help to avoid changing the shape, improve the feature of rub, gear and reduce the time to suit. This would also ensure the precision and result in a longer work piece life.

在以前研究的基础上，本论文重新探讨了电化学机械复合光整加工工艺的机理，确定了较合理的工艺参数，对电化学机械复合光整加工设备进行了改进，通过工艺实验广泛地搜集了大量实验数据，依据实验数据，多角度地研究了电化学机械复合光整加工的表面形貌特点，并且从理论上深入讨论了电化学机械复合光整加工表面形貌对工件工作性能的影响，最后得出的结论为：电化学机械复合光整加工对工件原始表面的低频成分有较大程度的降低，而对高频成分影响较小，有明显的阳极整平作用，被加工工件表面的尖峰状凸起被去除，工件表面呈现出微观&高原型&，表面轮廓不平度高度特性参数大幅度降低，工件表面轮廓分布集中，且呈负偏态，轮廓偏斜度为负值，轮廓支承长度率曲线陡峭，工件的表面质量得到综合改善，这对提高零件的抗接触变形能力、改善摩擦、磨损性能、降低工件的磨合时间、提高工件的精度保持性、延长工件的寿命均有利。

Calculates the coordinates of the spindle and drive shaft and checking the center distance, determined department spindle must use dislodges the gear.

根据柴油机齿轮室盖的结构特点、加工部位、尺寸精度、表面粗糙度及生产率等要求，确定该机床为单工位卧式组合机床；为确保加工精度，采用&一面两销&的定位方案；为实现无级调速，安全可靠，选择液压滑台；根据零件的大小及被加工孔的位置确定主轴箱的轮廓尺寸；由加工工艺选择滚珠轴承主轴，通过计算扭矩确定主轴和传动轴的直径；齿轮的模数是通过类比法确定；齿轮齿数和中间传动轴的位置是由&计算、作图和多次试凑&相结合的办法确定；计算主轴、传动轴的坐标并进行中心距验算，确定部分轴上需采用变位齿轮；轴上的齿轮套、键等零件按轴号选取相应的标准件。

It is one of the most widely used methods to groove and disconnect the workpiece with the cutter,but in the process of cutting the movement of the cross-feed can reduce the working orthogonal clearance,which increases the friction between the tool flank of the cutting tool and the machined surface,and hence results in the break of the workpiece and the working tool.

用切断刀对被加工工件切断或切槽是生产中应用最广泛的加工方法之一，但在切削过程中横向进给运动的影响使刀具工作后角减小，加剧了刀具后刀面与加工表面之间的摩擦，从而会导致工件被挤断，刀具易折断。

Screw compressor rotor machining tool wear the geometric calculation method : screw compressor rotor milling and processing a grinding two methods, usually conducted in two phases processing; first stage is rough, when the workpiece to be processed about its size to the second stage of Finished, when the rotor be processed into its final size when completed.

螺杆压缩机转子加工有磨削和铣削两种方法，通常分两个阶段进行加工；第一阶段为粗加工，当工件被加工到它的大概尺寸即可；第二阶段为精加工，当转子被加工成它的最终尺寸时完成。

Machining capability includes machining quality and cutting efficiency. Machines machining capability is usually assessed by the tiptop precision and superficial roughness that can be reached of the being processed part. The cutting efficiency is usually assessed by the most limit value of removal rate or cutting dosage.

机床的加工性能包括其加工质量和切削效率两个重要的方面，通常甩被加工零件能达到的最高精度和表面光洁度来评定机床的加工质量，用金属切除率或切削用量的最大极限值来评定机床的切削效率。

与被加工相关的网络解释 [注：此内容来源于网络，仅供参考]

contributory negligence：加工过失

早期英美法依加工过失(contributory negligence)观念,凡被害人有加工过失时,即被剥夺损害赔偿请求权,此乃源于其洁手原则(the principle of clean hand)之当然也,然此项原则过于严苛.

Donne：直接材料(在被加工之前直接呈现给意识的材料)

engagement 介入,卷入 | donne 直接材料(在被加工之前直接呈现给意识的材料) | en soi 自在

Plaice：欧蝶

丹麦渔船船队包括以下几种主要类型,一是拖网渔船和装备有丹麦式围网的渔船,主要捕捞鳕鱼和其他圆体鱼类( round fish) 、鲱鱼( herring) 和欧蝶( plaice) 以及其他一些被加工成鱼粉和鱼油的种类; 二是刺网渔船, 主要捕捞鳕鱼和一些比目鱼类;

Be processed：被加工成

Be moulded as 被塑造成为 | Be processed 被加工成 | Be disposed of 被处理

steaming：蒸; 引入蒸气; 蒸气加工

steam distillation 蒸气蒸馏; 气馏 | steaming 蒸; 引入蒸气; 蒸气加工 | stemfall 茎流 (雨水被树冠截留后沿树干徐徐留下)

unprocessed：未被加工的

ore 矿石 | unprocessed 未被加工的 | inconsistency 矛盾

upsetting：锻粗

摘要: 锻粗(Upsetting)加工是ㄧ基本的金属成型加工方式. 而锻粗工件与模具的接触面的摩擦现象是影响锻件品质的重要因素之一,也是一直被关心研究的课题. 对於塑性加工的研究,一般均假设模具与材料间的摩擦系数在整个工件与模具接触面间及在整个加工过程均为一定值,

machinability：可加工性

切削可加工性(Machinability)这一概念是二十世纪20年代中期首先由Herbert,Rosenhain和Sturney提出,在这一时期切削加工性主要是指切削速度与刀具耐用度之间的关系,而对切削表面质量,切屑去除和尺寸精度等的研究还不深入.切削加工性被看作是与材料的硬度,

MC machined：机械制造、机加工

maximum limit of size最大极限尺寸 | MC machined 机械制造、机加工 | measured feature被测要素

FeNi：铁镍

坡莫合金实质上是铁镍(FeNi)合金,其矫顽力很低,而饱和磁密Bs、磁导率和居里温度都很高,接近于纯铁.多元坡莫 合金,初始相对磁导率可达30000~80000,但是电阻率低,在10-7Ω-m左右,它可以被加工成极薄的薄片,