衬垫层

基本解释 (translations)

sarking

与衬垫层相关的网络例句 [注：此内容来源于网络，仅供参考]

Please put double dunnage in the lower holds and single in the tweendeck and lay mats where necessary.

请在底舱铺双层衬垫在二层舱铺单层，并在必要处铺上席子。

Blanket inserts must be narrower than the blanket, so that when the blanket frame, either side of the rubber blanket to tightly-coated surface to prevent various impurities, washing, water infiltration of blanket material and rubber surface on either side, lead to oxidation of secable drum and blanket delamination foaming and so on.

橡皮布的衬垫务必比橡皮布窄一些，这样当橡皮布绷不松后，橡皮布的双方才能牢牢不天包覆在滚筒暗不天，制止百般杂质、冲洗液、火等精神渗透橡皮布双方和橡皮滚筒暗不天，引起滚筒氧化生锈和橡皮布脱层起泡等题目。

In addition, a printing plate edge marked slopes or plate is too thin, or short-run printing of excessive wear lighter, so that the short-run suites and whitespace differences of high and low is too low and too soft pads, resulting in suites blank areaand, electro-chemical layer of aluminum foil, etc, should be made at the edge version slope near 90-degree right-angle (such as seihan with carving techniques that help you make little gradient edge version), according to the characteristics of the short-run suites, with thickness larger plate seihan, and a blank site, using a corrosion deeper stereoplasm lining for short-run; in addition, you should choose thin aluminized layer of anodized, adjust the appropriate business card printing and membership card making and adjusted pressure volume drum uponsize pressuer letoff drum.

此外，印版边沿存在明显的斜坡度或版材太薄，或印版过量烫印磨损变浅，使烫印版面与空白的高低差异太小，衬垫材料过软，造成版面空白部位与电化铝箔层接触等，应将版边沿坡度制成近90 度的直角(如采用雕刻工艺进行制版，可使版边沿几乎没有坡度)，根据烫印版面的特点，采用厚度大一些的版材制版，并将空白部位腐蚀深一点，采用硬质包衬进行烫印；此外，应选择镀铝层较薄的电化铝，调整合适的制卡和会员卡制作压力，并适当调整压卷滚筒压力和收卷滚筒拉力。

In LOCOS dry etching,silicon loss maintained at about 100 - 200 A,pad oxide layer reduced from 300 A to 135 A,and LOCOS oxide thickness change from 5000 A to 4000 A.

在LOCOS干法刻蚀时，对硅的刻蚀深度保持在100-200左右，衬垫氧化层从300减少到135，LOCOS热氧化厚度从5000？

Inner lining for floppy disk, filtering material, soundproof felt, speaker cloth, filter lining resisting high, temperature, isolated layer for battery, seal ring lining, polishing wheel, cloth, anti-shock lining, all kinds of industrial wiping, cloth, strengthening material for parabolic, electrically-isolated cloth, antenna plate, cable cloth, strengthening substrate cloth for glass steel, conformal insulation, material for electric, motor, abrasive cloth, cloth for ventilation pipeline, substrate for, industrial tape, hose substrate

计算机软盘内衬、过滤材料、音箱隔音毡、喇叭布、耐高温滤衬、电池隔层、密封环内衬、抛光轮、布、防震衬垫、各种工业擦布、抛物面天线、盘加固材料、电气绝缘布、电缆布、玻璃钢增强基布、电机适形绝缘材料、砂皮布、通风管道布等、工业胶带底、软管基材。

与衬垫层相关的网络解释 [注：此内容来源于网络，仅供参考]

dry layup：干法铺敷

dry lay-up 干法敷层 | dry layup 干法铺敷 | dry liner 干衬垫

mastic：胶粘剂

用隔汽的胶粘剂(mastic)或密封胶(sealant)密封外保温层的穿透部位,如风管吊架、温度控制传感器等部位. 用隔汽盖板和玛帝脂膜盖住焊接的销钉紧固件. 对于保温风管的吊架,提供一层刚性泡沫玻璃衬垫,或其他的不可压缩的不导热材料衬垫,

spacer：衬垫

本发明揭示固体高分子电解槽块及使用该模块的固体高分子电解装置,隔着具有导电性金属板的衬垫(spacer)层积多个固体高分子电解元件,在形成空气的气流路的同时形成立体的电解反应面.

cushioned grips：衬垫正视

6 hardened steel teeth with environmentally friendly, corrosion resistant coating 6淬硬钢的牙齿与环保,耐... | cushioned grips衬垫正视 | Hardened, cold-rolled, steel-laminate construction硬化,冷轧,钢层板...

sarking：衬垫材料

sarking 屋面衬板 | sarking 衬垫材料 | sarking 衬垫层

sarking：衬垫层

sarking 衬垫材料 | sarking 衬垫层 | sarmentose 蔓茎毒毛旋花子糖

sarking：衬垫材料 衬垫层 屋面衬板

sarkine 次黄质 | sarking 衬垫材料 衬垫层 屋面衬板 | sarkingboard 屋面衬板

sarmentose：蔓茎毒毛旋花子糖

sarking 衬垫层 | sarmentose 蔓茎毒毛旋花子糖 | sarmientite 砷铁矾

metal backing：金属插板,金属垫板,金属敷层,金属壳背,金属壳衬垫

metal back tube ==> 铝背显像管,金属敷层显像管 | metal backing ==> 金属插板,金属垫板,金属敷层,金属壳背,金属壳衬垫 | metal backup ==> 金属挡块

Clay liners：粘土衬垫

层柱粘土:Pillared interlayer clay | 粘土衬垫:Clay liners | 粘土方法:Clay mitigation