花键

基本解释 (translations)

spline  ·  splines

词组短语

multiple keys · multiple spline

与花键相关的网络例句 [注：此内容来源于网络，仅供参考]

Key or 6 key square serration axle is the traditional structure of starter armature shaft for auto and tractor and has been replaced by cold rolling multi key involuting serration axle.

铣削加工的四键或六键矩形花键是汽车、拖拉机用起动机电枢轴上的传统结构，已逐渐被用冷滚轧加工的多键渐开线螺旋花键所代替。

"A slip joint consists of outside splines on one shaft and matching internal splines in the mating hollow shaft , the splines cause the two shaft s to rotate together But permitthe two to move endwise with each other."

伸缩花键由在传动轴上的外花键和与之相连的空心轴中对应的内花键组成。伸缩花键使两轴一起转动，也能使两轴相对移动。

"A slip joint consists of outside splines on one shaft and matching internal splines in the mating hollow shaft, the splines cause the two shafts to rotate together But permitthe two to move endwise with each other."

伸缩花键由在传动轴上的外花键和与之相连的空心轴中对应的内花键组成。伸缩花键使两轴一起转动，也能使两轴相对移动。

Nominal Clearance is the actual space width of an internal spline minus the actual tooth thickness of the mating external spline. It does not define the fit between mating members, because of the effect of variations.

理论侧隙：理论侧隙是内花键的实际齿槽宽减去与之相互配合的外花键的实际齿厚所得的值由于内、外花键在配合时会产生一定的公差，所以理论侧隙不能够用于确定相互配合的内、外花键之间的间隙

The splines consist of two sets of teeth, an internal set on the hub of the friction disk and a matching external set on the clutch shaft.

花键包括二套花键齿，在摩擦盘轮毂上的内花键齿和在离合器轴上与前者相配的外花键齿。

The clutch disc has a splined hub that fits over splines on the transmission input shaft . A splined hub has grooves that match splines on the shaft . These splines fit in the grooves . Thus , the two parts held together .

离合器片上带有花键毂，与变速箱输入轴花键匹配，花键毂上有与一轴相匹配的凹槽，这些是花键与键槽配合，因此能结合在一起。

The clutch disc has a splined hub that fits over splines on the transmission input shaft . A splined hub has grooves that match splines on the shaft . These splines fit in the grooves . Thus , the two parts held together . However , back ?

离合器片上带有花键毂，与变速箱输入轴花键匹配，花键毂上有与一轴相匹配的凹槽，这些是花键与键槽配合，因此能结合在一起。

1 Rectangular spline Processing of convenience, can be used to obtain high precision grinding method, but usually use within the spline spline broach, spline hole for the unreasonable can not be processed, had to use slotting processing, low accuracy.

1.1 矩形花键加工方便，可用磨削方法获得较高的精度，但内花键通常要用花键拉刀，对于不通孔的花键就无法加工，只好用插削加工，精度较低。

Spline Broach complexity of the design process, the geometric parameters, many of which need to look-up table and complex calculation to determine the parameters of a certain size, Design Spline Broach all forms and formulas into C language are procedures, through a simple C program calls, importation Spline Broach the technical parameters can be accurately its design parameters, Finally, all the parameters of integrated print out data tables, thus simplifying the complex Spline Broach design process, and meet the design requirements.

花键拉刀设计过程复杂，几何参数多，许多都需要查表和复杂的计算来确定某一参数尺寸，把花键拉刀设计中所有表格和计算公式都编成C语言程序，通过简单的C程序调用，输入花键拉刀的技术参数就可以准确得到其设计参数，最后把所有的参数值综合打印出数据表格，从而简化了复杂的花键拉刀设计过程，且达到了设计的要求。

Spline Broach complexity of the design process, the geometric parameters, many of which need to look-up table and complex calculation to determine the parameters of a certain size, Design Spline Broach all forms and formulas into C language are procedures, through a simple C program calls, importation Spline Broach the technical parameters can be accurately its design parameters, Finally, all the parameters of integrated print out data tables, thus simplifying the complex Spline Broach design process, and meet the design requirements.

花键拉刀设计过程复杂，几何参数多，许多都需要查表和复杂的计算来确定某1参数尺寸，把花键拉刀设计中所有表格和计算公式都编成C语言程序，通过简单的C程序调用，输入花键拉刀的技术参数就可以准确得到其设计参数，最后把所有的参数值综合打印出数据表格，从而简化了复杂的花键拉刀设计过程，且达到了设计的要求。

与花键相关的网络解释 [注：此内容来源于网络，仅供参考]

spline：花键

以前,利用花键(Spline)传递旋转力的中间轴是主流. 由于使用滑动摩擦方式,无法同时兼顾旋转方向的刚性和伸缩方向的灵活性. 为了改为滚动摩擦方式,有些产品使用了滚珠,但只是在原来的花键上增加了滚珠而已,仍需保留花键. 旋转力较小时,

spline feed rod：花键进给杠

spline coupling 花键联轴节 | spline feed rod 花键进给杠 | spline gear 花键齿轮

spline wear gauge pin：花键磨损计量针

spline wear;花键磨损 | spline wear gauge pin;花键磨损计量针 | spline wear pin;花键磨损针

splined：用花键联结的

splined 用花键联接的 | splined 用花键联结的 | splined 用花键连接的

splined：用花键联接的

splined shaft 花键轴 | splined 用花键联接的 | splined 用花键联结的

SPLINED HUB：花键套节

splined fitting 花键座 | splined hub 花键套节 | splined shaft 花键轴

SPLINED HUB：花键配合轮毂

splined governor shaft;花键配合调速器轴 | splined hub;花键配合轮毂 | splined input connection;花键配合输入连接

splined joint：花键接合

spline shaft 花键轴 | splined joint 花键接合 | splined shaft 花键轴

spline shaft：花键轴,多键轴,多槽轴

spline ring gauge ==> 花键环规 | spline shaft ==> 花键轴,多键轴,多槽轴=>スプラインシャフト | spline shaft gear ==> 花键轴齿轮

spline shaft gear：花键轴齿轮

spline shaft ==> 花键轴,多键轴,多槽轴=>スプラインシャフト | spline shaft gear ==> 花键轴齿轮 | spline shaft grinding machine ==> 花键轴磨床