- 更多网络例句与艉轴相关的网络例句 [注：此内容来源于网络，仅供参考]
-
Preparing for installation of tail shaft: the end screw of tail shaft should be tied up with cloth or thin rubber, in order to protect impact during the assembly.
艉轴的安装准备：艉轴末端的螺纹部分用布或薄橡胶皮包扎好，防止在装配中碰伤。
-
Shell plate to be thickened or double plate to be added for hawse pipe and exit of propeller shaft.
锚链筒及艉轴出口处增加外板厚度或加复板。
-
On the ship center line of the dock, a laser equipment (this laser equipment only can turn in same vertical face)is put on someplace between the Fr –3# and the Fr 7.5#.
在船坞底船体中心线上，-3#肋位与艉轴管后端面所在肋位之间某处放一激光仪（此激光仪只能在同一重垂面内转动），然后分别用激光打-3#肋位及艉轴管后端面两处的钢丝心，确定这两点在船中心面的内，及已确定了整根轴线在同一中心面上。
-
As the ship stern shaft bearings not before, according to Stern stern tube axis Boring map (SC5084 - 425-02-06), after housings Boring to provide size of the front and bow closures linked to the provisions of Department Boring size.
由于本船艉轴没有前轴承，根据艉轴艉管镗孔图（SC5084-425-02-06），将后轴承座镗孔至规定尺寸，以及将前部与艏密封盖联结处镗至规定尺寸。
-
Respectively lase both sides of the stern tube in order to measure the boring dimensions roughly.
在艉轴管前后分别用激光粗打镗孔余量的分布情况。
-
Fitting and tightness testing of propeller shaft before launching.
艉轴密性装置的安装与密性试验
-
Preparing work before tail shaft installation, the flushing oil and the integrity of stern tube should be delivered to ship-owner and surveyor.
安装前的清洁：用压缩空气和棉布将艉轴管及艉轴彻底清洗干净。3。艉轴安装前的准备工作：艉管串油与艉管密性已经交检结束。
-
The main products have the stern tube shaft, stern tube bearing white alloy, rubber bearings, high-polymer bearings, tail shaft, intermediate shaft, the upper and lower rudder stock, oil lubrication, water lubricated seal device and its accessories.
主要产品有艉轴管，艉管白合金轴承，橡胶轴承，高聚体轴承，尾轴，中间轴，上、下舵杆，油润滑、水润滑密封装置及其配件等。
-
With protected stuff at colligation part in order to protect tail shaft , send the tail shaft into the stern tube slowly with manual crane , during the process , we should align the tail shaft and stern tube carefully in order to protect the impact between the stern tube bearing and the screw of tail shaft .
起吊艉轴并送入艉管内：在绑扎钢丝绳的部分包上麻包布以保护艉轴后，即可起吊艉轴；然后用葫芦将艉轴慢慢送入艉管内达到预定位置，在送进过程中，要注意将艉轴对准艉管，防止艉轴承和艉轴螺纹与之相碰。
-
A procedure for alignment of the shaft and forward stern tube seal without affecting the M/E alignment is developed,and the leakage at the stern tube seal is eliminated.
根据测量&嘉升&轮左艉轴在不同轴承布置状况下的运行，相应进行了四阶振动测量和滚振计算，发现在不影响主机对中的情况下，可以得到一个轴系校中和前艉轴封校中的方法，从而解决了艉轴封的漏油问题。
- 更多网络解释与艉轴相关的网络解释 [注：此内容来源于网络，仅供参考]
-
Stern tube boring：艉轴管镗孔
1.Lighting alignment for shafting & rudder system 轴舵系照光对中 | 2.Stern tube boring 艉轴管镗孔 | 3.Stern tube bush 艉轴衬套
-
propeller shaft bracket：艉轴架
"轴包架,轴包套","propeller shaft bossing" | "艉轴架","propeller shaft bracket" | "艉轴衬","propeller shaft lining"
-
tail shaft packing：艉轴迫紧
串行引擎 tandem engine | 艉轴迫紧 tail shaft packing | 索尾滑车 tail block
-
tail shaft packing：艉轴填料{迫紧}
回旋试航 tactical trial | 艉轴填料{迫紧} tail shaft packing | 串联螺桨 tandem propeller
-
stern tube：艉轴管
stern n. 船艉,艉柱 | stern tube 艉轴管 | stiffener n. 扶强,加强筋
-
stern tube gland：艉[轴]管压盖
双[胴]体船 catamaran | 艉[轴]管压盖 stern tube gland | 升[压]变压器 step-up transformer
-
stern tube bushing：艉轴管衬套
艉轴套轴承 stern tube bearing | 艉轴管衬套 stern tube bushing | 艉轴套迫紧端板 stern tube end plate
-
stern tube bearing：艉轴套轴承
艉轴管 stern tube | 艉轴套轴承 stern tube bearing | 艉轴管衬套 stern tube bushing
-
stern tube sealing：艉轴管轴封
艉轴套压 stern tube packing gland | 艉轴管轴封 stern tube sealing" | 艉管轴 stern tube shaft
-
sea water lubricated stern tube bearing：海水润滑艉轴管轴承
封闭焊珠 sealing bead | 海水润滑艉轴管轴承 sea water lubricated stern tube bearing | 自闭停止阀 self-closing stop valve