- 更多网络例句与自动注入的相关的网络例句 [注：此内容来源于网络，仅供参考]
-
The page used to view a specific issue is a nodeless page, and it is not included in the site structure; we simply redirect to this page from our module, and Cuyahoga injects the page code automatically.
用于查看特定问题的网页是无节点网页上，而且不包括该网站的结构，我们简单地重定向到这个网页从我们的模块，凯霍加注入的页面代码自动。
-
The results showed that: 1 during drying, the heat transferred between process gas and cut tobacco before feeding point in HXD could be scaled by ', which is the reciprocal of temperature difference of process gas...
结果表明：①在干燥过程中，HXD喂料点前工艺气流与烟丝间的换热量可用干燥前后工艺气流温差的倒数来衡量；②在其它控制参数不变，只改变排潮模式的情况下，设置为手动控制排潮时，干燥过程的换热量总是较低；③当设置为自动排潮且HXD蒸气注入量超过1800kg/h时，工艺气流的干燥能力随着注入量的增大而降低。
-
Contract:This article disausses the principal of main steam temperature control system according the problems in running,including the unreasonable main steam pressure set point volue,hot air injection flow is not acciurate,Charge of steam temperature has the big delay and the common PID can′t satisfy the regulate′s demandthen take the according measures,adopt smith predictor,change to ABB intelligent positioner,add the hot air injection antiblock device,test the main steam temperature automation and optimization the specificator.
中国国电集团公司菏泽发电厂热工，山东摘要：本文论述汽温控制系统组成原理，针对运行中发现的问题，包括一次风母管压力自动设定值设计不合理，导致主汽温度和再热汽温度变化幅度加大，底部注入风量和汽温参数测量不准确，汽温变化迟延大，常规PID满足不了调节要求，采取了相应措施，改用史密斯预测器，更换为ABB定位器，增加底部注入风量等测点防堵装置，并对主汽温自动进行试验和参数优化。
-
Specification, technical details and any approval certificate of all gas and electrical components on the fuel system such as the LPG pipework and flexible hoses (design standards, pressure, material and size), solenoid valve, LPG converter/vaporiser including the operating pressures at primary and secondary
燃料系统上各气体及电器组件的技术细节，规格及任何批准证书，例如石油气喉管和软喉(设计标准、压力、材料及尺寸)、电磁阀、石油气蒸发器/转化器(包括初级和次级的工作压力)、安全泄压阀、溢流控制阀、止回阀、过滤器、手动截气阀、液位计、注入自动截流器等
-
With analysis on the control model, an improved automatic tuning method for arc-suppression coil is proposed, that is: adopting voltage feed forward control to restrain interfere of 50Hz displacement voltage, which can improve the characteristic of the injected signal significantly, make the injected signal without reference to unbalanced network and neutral displaced system. Another innovation is detecting the magnitude of neutral point signal-frequency voltage to judge the resonant state, which improves the sensitivity and accuracy of resonant judgement effectively.
基于对控制模型的分析，提出了一种新的注入变频信号的消弧线圈自动调谐方法：通过电压前馈校正控制的引入，有效抑制了50Hz工频电压对注入信号的干扰，使得注入信号不受电网不对称及中性点位移电压的影响；提出以中性点注入信号电压幅值最大做为新的谐振判据，有效提高了谐振状态判断的灵敏度和准确度。
-
of Use: when the tyre was punctured leakage, as long as this meeting with fetal connected to the tire of the above, press meeting fetal fluid valves will be automatically compressed air to the tire Riga, but also into the same plastic as the white - Fetal plastic, tire pressure to be normal, activate the car, a trip.
使用方法：当轮胎被扎破漏气后，只要用这个补胎液连接到轮胎上面，按下补胎液的阀门，会自动往轮胎里加压缩空气，同时也会注入像发胶一样的白色的补胎胶，待轮胎压正常后，开动车，就行了。
-
S:Well,the self-filling device is simple,sir.
噢，先生，这种笔的自动注入很简单。
- 更多网络解释与自动注入的相关的网络解释 [注：此内容来源于网络，仅供参考]
-
Mold：金属模具
二,模内转印(IMD)技术所谓IMD,就是将已印刷好图案的膜片放入金属模具(mold)内,通过送箔机器自动输送定位,然后将成形用的树脂注入金属模内与膜片接合,使印刷在膜片上的图案跟树脂形成一体而固化成产品的一种成形方法,
-
money order：匯票
您可以至附近办理外汇的银行电汇,将资金注入您在美股券商的帐户,如果您在美国当地的银行有帐户的话,可以使用该银行的个人支票、银行本票(Cashier's Check)、汇票(Money Order)存款、或者银行自动转帐(ACH Money Direct)存款.
-
scrambler：扰码器
* 当系统起动时,扰码器(Scrambler)自动配置并建立与不同CAS的连接;* 每套CAS的ECMG轮流向扰码器发出回复授权控制信息ECM,并由同密同步器(SCS)注入到传输流中.
-
autoreinfusion：自体输血, 自体再注入
autoregulatory | 自动调整的 | autoreinfusion | 自体输血, 自体再注入 | autorelay | 自动继电器
-
fuel injection system：燃油喷射系统
燃油喷射系统(Fuel Injection System)根据发动机的需要用电子控制的方式自动提供空气和燃油混合比例. 这有助于改善发动机效率和减低油耗. 不象化油器,将空气和燃油混合后再入渗透汽缸. 燃油喷射系统直接将所需要的燃油精确的注入汽缸.