脱层

基本解释 (translations)

leafing

与脱层相关的网络例句 [注：此内容来源于网络，仅供参考]

So, in order to avoid the delamination, not only the matrix but also other factors must be studied.

即内部脱层是多因素综合作用的结果，为了避免壳体内部脱层必须考虑多种因素。

In this paper, firstly the influence of the delamination upon the natural frequencies of a laminated beam is studied in detail. By partitioning the delaminated beam, its natural frequencies are obtained.

本文首先详细分析了层合梁的脱层现象对其振动频率的影响，通过对脱层梁进行分区处理，得到了脱层梁自振频率变化的规律。

It has important value both on theory and practical application to study mechanism of delaminations,loading characteristics of delaminated structures and improvement on structural performance against delamination.

研究脱层机理、脱层结构承载特性以及怎样提高层合结构的抗脱层性能，对复合材料层合结构的工程应用具有重要的理论和实用价值。

In the other hand, because the delaminations are not known in the composite laminated structures, the understanding the delaminated parameters are the first problem for the mechanical analysis of the structures.

另一方面，复合材料结构中的脱层往往是未知的，了解脱层参数成为脱层结构力学分析的首要条件。

In the example, the critical remote strain and the buckling configuration for different length-to-thickness ratios of delaminating are given.

用Mathematica编程进行算例分析，给出了不同电极脱层长厚比的临界应变载荷和脱层的屈曲形状，研究了压电体的机电耦合效应对临界载荷的影响。

Both surfactants can intercalate into the layers of the pristine clay dispersed in water prior to polymerization. Although the d spacing of the POSS-intercalated clay is relatively smaller than that of the CPC-intercalated clay, PS more easily intercalates and exfoliates the POSS-treated clay than the CPC-treated clay.

插层剂预先插层到分散於水中的黏土后再进行乳化聚合反应，虽然POSS插层后黏土的层间距离较CPC插层后的层间距离小，但聚苯乙烯与POSS互容性较佳，所以易使黏土达到脱层结构，而CPC则反之。

Parameters of anticline, which are from seismic and geological sections of the Cizhuya propagation anticline, respectively, give the consistent depth and dip angle of detachment fault at 8.10-8.63 km and 29°-45°.

根据地震剖面的解释及地表资料整理结果，把上述演算结果应用于重庆方斗山地区的茨竹亚背斜的2个剖面中，计算出隐伏滑脱层的深度分别为8.10~8.63 km，证明茨竹亚背斜隐伏主滑脱层发育于寒武系底部。

The surface on the steel bridge is easy to damage early than estimate years.The distress types in steel bridge surfacings include permanent deformation,cracking,formation of mounds and disintegration.The text analyses the vertical section strain under tire location by use of the finite element method and calculates the influence of stiffness variance of translate bonding layer on the surfacings of steel bridges.

中文摘要：钢桥面沥青铺装层在使用一段时间后容易出现开裂、脱层以及车辙等早期破坏现象，采用空间有限元分析方法对车轮荷载位置处的截面竖向应变进行分析，计算了过渡粘结层刚度变化时对钢桥面铺装层受力变化的影响，计算结果说明对传统的弹性层状计算理论的假定与实际受力情况存在较大差异。

Following conclusions are concerning the strength of filament wound solid rocket motor case:(1) The inter-delamination is important for the strength of the case, and there are many factors, such as, the matrix, the interface, the fiber volume fraction, the fiber arrange pattern, to influence on the delamination.

最终结合宏观、细观两方面的研究和分析，并联系到纤维缠绕固体火箭发动机壳体的强度，可以得到如下结论：（1）壳体的内部脱层是导致壳体强度下降的重要原因，而影响壳体内部脱层的因素除了基体材料外还有界面，纤维的排列阵列、体积分数，壳体的铺层次序等。

With analysing the the fatigue mechanism, the general mode of interply fatigue damage propagation is denoted by delamination length and crack density. Based on the power-law, the relationship between number of cycles and delamination length and crack density are established. The specimen is modeled as an equivalent six-ply material system. Starting with the analysis of interply stress, the interply shear stress under cyclic loading is calculated by using nonlinear three-demension FEA. According to the stage regularity of fatigue damage propagation, such models as average strain, effective modulus, ratio of delamination length and crack density, experimental relationship between crack density and effective modulus, are proposed by introducing subsection coefficient.

通过对疲劳机理的分析，确定了以脱层长度和裂纹密度表示的层间疲劳损伤演化的一般模式，利用指数法则建立了脱层长度和裂纹密度随疲劳循环周次变化的关系；从层间应力分析入手，以等效六层的材料模型对循环载荷下的层间剪切应力进行了三维非线性有限元分析；根据疲劳损伤扩展的阶段性，引入分段系数，分别建立了平均应变与载荷循环周次的分段线性模拟模型、有效刚度随载荷循环周次的变化关系模型、裂纹密度变化和脱层长度变化关系随载荷循环周次变化的分段线性模型以及疲劳裂纹密度和有效刚度关系的经验模型。

与脱层相关的网络解释 [注：此内容来源于网络，仅供参考]

delamination：脱层

TCT的目的主要是因为利用各种材料间不同的热膨胀系数不匹配(CTE mismatch)现象,在长期的高温与低温循环过程中产生导通孔断裂或产品脱层(delamination)等问题,以协助找到产品品质风险.

delamination resistance：抗脱层性能

delamination 脱层(作用) | delamination resistance 抗脱层性能 | delay time 延迟时间

delamination resistance：抗分层性,抗脱层性

delamination resistance | 抗分层性,抗脱层性 | delanium | 人造石墨 | delay | 时延,延迟

Ply Steel：复合钢,复层钢,多层钢

ply separation 脱层,离层 | ply steel 复合钢,复层钢,多层钢 | ply turn-up 卷边

delaminate：脱层

deionization 消除电离作用 | delaminate 脱层 | delaminated clay 涂布粘土

delaminate：分层,脱层

Deflection 挠度,挠曲 | Delaminate 分层,脱层 | Delinerate 描绘,叙述,描外形

addling：抹灰脱层

addlepateddippy 昏头昏脑的 | addling 抹灰脱层 | addling 抹面剥落

addling：抹灰脱层/抹面剥落

addlepated /昏头昏脑的/ | addling /抹灰脱层/抹面剥落/ | addometer /加算器/

Delaminating：脱层

corrugated container 瓦摆纸箱. | Delaminating 脱层 | Gouge 锉孔

Delaminating：剥离;脱层

印花毛洋纱布 delaine | 剥离;脱层 delaminating | 迟延弹性回复 delayed elastic recovery