组装

基本解释 (translations)

pkg

与组装相关的网络例句 [注：此内容来源于网络，仅供参考]

The results show that BDT can be assembled on the surface of copper electrode to form monomolecular self-assembled membrane,and the membrane can efficiently inhibit the copper base corrosion in the 3% NaCl corrosion medium and acidic solution.

实验表明：BDT能够有效地组装到铜的表面形成单分子自组装膜，BDT自组装膜能有效地抑制铜基底在3%NaCl腐蚀介质以及酸性NaCl溶液中的腐蚀行为；缓蚀效率随组装时间的延长逐渐升高并趋于稳定，在pH值较低的溶液中仍具有较好的缓蚀效果；当BDT浓度为1.0×102 mol/L、组装时间为40 h时，铜电极的腐蚀电流最小，缓蚀效率最好。

The influence of different assembled condition such as assembly method, concentration of zirconium source and pH value on the effectiveness of assembly were evaluated via DSC-TG, FT-IR, Uv-vis and SAXRD et al. It showed that the assembly effectivness of uncalcined 3 Si/Zr_10# sample was best.c The optical characteristic, which including light-conduction in infrared band and polarity in visible band, of dip-coating film and membrane assembled zirconia after processing parameters of assembly optimized were observed via FT-IR and Uv-vis. The polarity was characterized by polarizing angle through calculation from light-transmittance, light-reflectance and fresnel coefficient. qualitative analysis showed that the polarity of Si/Zr_10 # dip-coating film assembled was best.d Adopting zirconium oxychloride as zirconium source, CTAB as template, employing different CTAB adding sequence, two mesoporous zirconia samples were prepared. The template effect of two samples was discussed. It showed that the effect of the sample which CTAB adding sequence was same as mesoporous silica film was better. The light-conduction in infrared band of these samples was also studied, which offered comparison to the polarity of zirconium dioxide assembled within mesopore.

结果显示：组装条件优化后的uncalcined 3 Si/Zr_10#厚膜样组装效果最好，其组装液对应的pH值最利于该锆源离子模板交换组装； c选用FT-IR、Uv-vis对组装条件优化后纳米氧化锆/介孔氧化硅厚膜、纳米氧化锆/介孔氧化硅薄膜包括红外导光性、可见光区内的偏光性在内的光学特性进行了分析，其中偏光性以膜层透光性、反光性及菲涅耳系数计算出的偏振角即布儒斯特角表征，定性分析显示，Si/Zr_10#ZrO_2/介孔氧化硅厚膜偏光性最好； d以氧氯化锆ZrOCl_2·8H_2O为锆源，CTAB为模板剂，采用不同的模板剂加入顺序，探索性地制备两介孔氧化锆样，分析了两介孔氧化锆样的模板效果，得出模板剂加入顺序同介孔氧化硅薄膜时介孔氧化锆样的模板效果较好，并分析了所得样品的导光性，为锆氧粒子引起的附加光学特性分析提供了参考和对比。

On the basis of molecular design, urushiol and tyrosine, with unique chemical structure, were selected as units to fabricate five kinds of stable and functional multilayer films via layer-by-layer self-assembly method.

本论文在对自组装膜的发展历史、自组装技术进行综述的基础上，从分子设计的思想出发，选用具有独特结构和性能的功能分子——漆酚和酪氨酸作为组装基元，以层层自组装技术制备了五种新型的，具有高稳定性的功能多层膜。

The UV and IR spectroscopic studies of the monomer films showed that the photoreaction ratio of monomer (about 50%) was higher than the corresponding photosensitive polymer (about 10%, PVCi). The polarized IR spectra proved that obvious anisotropic absorption was displayed in the irradiated photosensitive film. With polarizing microscopy method, we found that these kinds of photoalignment films exhibited good alignment ability, and the stability of the photoalignment film could reach about 100℃. 2 A photosensitive self-assembled monolayer was fabricated that contained photo-cycloadditable groups, such as, coumarin and cinnamate. The reaction process were detected by contact angle method because the IR absorption of monolayer was very weak. The photosensitive self-assembled monolayer promote uniform alignment of nematic liquid crystals by LPUV, and it thermal stability could reach about 130℃. 3 A cationic bolaform amphiphiles was synthesized that had two photosensitive double bonds, and can be polymerized by ultraviolet. A layer-by-layer self-assembled deposition film was prepared in aqueous solution by using this material and poly (sodium 4-styrenesulfonate). The UV-Vis. spectra proved that the multilayers film was uniform and layer-by-layer. When LPUV irradiated the film, the photopolymerizable double bond underwent [2+2] cycloaddition, and the production of the reaction distributed along the polarized direction of incident LPUV. Polarized UV-Vis. spectra indicated that the irradiated self-assembled multiplayer film was anisotropic, and the dichromic ration is about 0.09, it is higher than the spin-coating method of photosensitive polymer or monomer. We used this anisotropic film as alignment layer of nematic liquid crystals, and obtained a uniform and stability alignment result, the static contrast ratio is about 100, which is very close to application of liquid crystal device. This thesis is an instance that the photochemical material was used in the physics region of liquid crystals, the route that was from photosensitive monomer, self-assembled monolayer film to self-assembled multiplayer film was undergone, by this logical research method photoailgnment of liquid crystal was extended and consummated.

围绕上述思路开展了如下工作：1合成了三种可进行光二聚反应的光敏小分子单体，LPUV 辐照制作了光控取向膜；用紫外-可见光谱法和红外光谱法分析了薄膜中的光化学反应，发现小分子的光反应程度可达到50%以上，至少比光敏高分子高出5倍；薄膜的偏振红外光谱证实，经过LPUV 辐照后薄膜出现了明显的各向异性；将小分子光控取向膜制成液晶器件，在偏光显微镜下观察看到均匀一致的液晶取向；并且热稳定性达到100℃左右，接近实用化要求。2制备了含肉桂酸、香豆素基团的自组装单层膜；采用接触角的方法监测自组装反应的动力学过程；紫外-可见光谱证实了自组装单层膜在石英基板表面形成；自组装单层膜经LPUV 辐照后能诱导液晶均匀取向，而且热稳定性可达130℃，热稳定性进一步提高。3合成了含有光敏双键的双季铵盐，在水溶液状态下将它和聚乙烯基苯磺酸钠沉积生成layer-by-layer 自组装多层膜，紫外-可见光谱证实这是一个逐层均匀的沉积；在LPUV 照射下，自组装膜中的光敏双键按照偏振方向发生[2+2]环加成反应，形成取向膜，用二向色性值评价的分子取向度高于高分子及小分子光控取向膜的水平；实验证明用自组装多层膜制成的液晶器件亮暗态均匀，静态对比度约为100，达到实用化器件的水平。

The two-dimensional structural units (such as silicon-oxygen tetrahedral sheet, octahedral sheet), interlayer space are assembled according to the sphere close packing manner, and the close packing layers parallel to {0001}. There are several mechanisms to release the difference in size while the silicon-oxygen tetrahedral sheet and octahedral sheet assemble the TO and TOT-type structural layers. The two types of structural layers with different interlayer space fitted together in six kinds of assembling modes and formed six kinds of crystal layers. The combinatorics analysis of the two-dimensional structural units revealed that there may be 28 kinds of TOT type interstradified minerals in six kinds of polysomatic assembling modes of interatradified structure. The structural layer is symmetrical for octahedron sheet in the structure of interstratified minerals and shows polarity characteristics.

结果表明，不同二维结构单元体（包括硅氧四面体片、八面体片、层间域的构筑基本符合球体紧密堆积原理，紧密堆积层平行{0001}；四面体片与八面体片构筑TO和TOT结构层时采取多种机制消除二者在二维尺寸上的差异；两种模式的结构层与不同类型的层间物组装形成六种组装模式的晶层；并通过二维结构单元体的组合规律的分析，计算出可能存在的28种TOT型间层结构，它们分属于6种间层结构多体性组装模式；间层结构中，结构层对于八面体片是不对称的，并在属性上表现出极性特征；间层矿物的晶层类型可用6种多体性组装模式加以表达。

A novel polymer of Poly(diglycidyl maleate-co-stearyl methacrylate) was synthesized and its structure was characterized by ~1H NMR. Its self-assembly behavior was studied in different solvents. It was found that vesicles and tubule-liked aggregates can be obtained through self-assembly of P(DGMA-co-SMA)/THF/EtOH system. And spheral aggregates were obtained in P(DGMA-co-SMA)/THF/H_2O system while the spheral aggregates were converted into rod-liked aggregates and line-liked aggregates after aged for different time.

合成了带含环氧基侧链和十八烷基侧链的聚(马来酸二缩水甘油酯-co-甲基丙烯酸十八酯)，用~1H NMR对所得的共聚物进行了表征；研究了其在选择性溶剂中的自组装行为，发现P(DGMA-co-SMA)／THF／EtOH体系可以通过自组装形成囊泡形自组装体和支化的管状自组装体，P(DGMA-co-SMA)／THF／H_2O体系最初自组装形成球形自组装体，随着陈化时间的延长，球形自组装体逐渐融合成长条形自组装体和线形自组装体；探讨了自组装过程的机理，建立了可能的自组装过程模型。

The factors of temperature and humidity influenced on film thickness and order of layer were studied, in which pulling speed and pulling times were also included. It showed that the thickness of single dip-coating film reached 0.23 μm ~ 0.625 μm, and the degree of order of surface layer were still holding much higher.b Adopting calcined or uncalcined mesoporous silica membrane as matrix, nano zirconia particles were assembled through ion exchange method and ion-template exchange method.

结果表明，单次提拉膜膜厚0.23μm～0.625μm、8次提拉后表层膜仍有一定的有序性； b以自制的介孔氧化硅煅烧/未煅烧厚膜样为基体，采用离子交换法/离子模板交换法组装锆氧纳米粒子，选用DSC-TG、FT-IR、Uv-vis、SAXRD等对不同组装方法、锆源浓度、pH值等组装条件下ZrO_2/介孔氧化硅厚膜组装效果进行评价。

Such assemblers『组装产品』 account for some 35% of the market.

这样的组装产品占到了市场的35%。

Sensing ability of PSS/PANI self-assembled film with different doping/dedoping structure to DMMP and CEES was investigated. Results demonstrate that the gas sensitivity of PSS/PANI self-assembled film is affected by the size of dopant counterions. Gas sensitivity of self-assembled film increases with increasing size of dopant counterions. It is found that sensing ability of PSS/PANI self-assembled film to DMMP increases significantly by redoping/dedoping EB-PSS/PANI film with sarin acid that has similar structure with DMMP.

首次考察了不同掺杂/脱掺杂结构的PSS/PANI自组装膜对化学战剂模拟剂DMMP和CEES的敏感性能，研究表明，掺杂酸对离子的尺寸大小对PSS/PANI自组装膜的气敏性有很大影响，较大的对离子尺寸有利于提高自组装膜的气敏性；并且发现采用与DMMP结构类似的沙林酸对EB-PSS/PANI自组装膜进行再掺杂-脱掺杂，能显著提高PSS/PANI自组装膜对DMMP的敏感性能。

In contrast, the kobs of complex SAM changes slightly with the assembling time. After an assembling time of 76 h, the kobs of complex SAM is two order of magnitude larger than that of Azo SAM.

而Azo与β-CD包合物自组装膜的kobs值随组装时间变化不大，在组装76h以后，包合物自组装膜的kobs比单纯偶氮苯自组装膜的kobs高2个数量级以上。

与组装相关的网络解释 [注：此内容来源于网络，仅供参考]

assembled：组装

得知首批车是全进口大件组装(assembled)的,物有所值得知首批车是全进口大件组装(assembled)的,物有所值毕加索一直都是由全进口大件组装(assembled)的,2.

Assembly line：组装线

简答题 某组装线(Assembly Line)作业现场如下右图,该组装线共计有16名员工负责生产,但因为生产线不平衡的关系,造成生产力低落,请问一条不平衡的组装线会有哪些状况可以判定,而又应如何进行改善?

special assistant manager：特助 (组装专业词汇)

general manager|总经理(组装专业词汇) | special assistant manager|特助 (组装专业词汇) | factory director|厂长 (组装专业词汇)

bezel panel：面板 (组装专业词汇)

chassis|基座 (组装专业词汇) | bezel panel|面板 (组装专业词汇) | power button|电源按键 (组装专业词汇)

power button：电源按键 (组装专业词汇)

bezel panel|面板 (组装专业词汇) | power button|电源按键 (组装专业词汇) | reset button|重置键 (组装专业词汇)

die change：换模(组装专业词汇)

defective product box|不良品箱(组装专业词汇) | die change| 换模(组装专业词汇) | to fix a die|装模(组装专业词汇)

feature change：特性变更 (组装专业词汇)

stock change材料变更(组装专业词汇) | feature change |特性变更 (组装专业词汇) | evaluation|评估 (组装专业词汇)

vaccum cleaner：吸尘器 (组装专业词汇)

mop|拖把 (组装专业词汇) | vaccum cleaner|吸尘器 (组装专业词汇) | rag|抹布 (组装专业词汇)

linear cutting：线切割 (组装专业词汇)

driller|钻床 (组装专业词汇) | linear cutting|线切割 (组装专业词汇) | electrical sparkle|电火花 (组装专业词汇)

deburring punch：压毛边冲子(组装专业词汇)

Conveyer|流水线物料板(组装专业词汇) | deburring punch|压毛边冲子(组装专业词汇) | Assembly line|组装线 (组装专业词汇)