- 相关搜索
- 磨损的:鞋跟穿掉了的
- 织物磨损后落下的碎片
- 防磨损的
- 抗磨损的
- 更多网络例句与磨损的相关的网络例句 [注:此内容来源于网络,仅供参考]
-
With the automatization of degree have improved in the industry, the demand of the mechanism continuity and security also have increased, the reason that cause the operation of mechanism to invalidation is the wear by the friction, which abrade the movement component and joint component.
随着工业自动化程度的提高,对机械零件工作的连续性、安全性要求也提高,而实践证明,导致机械运转失效的主要原因是由于活动构件或者联结件在摩擦力的作用下产生的磨损,磨损导致机械的运转失效,更可能引发安全隐患,这其中磨料磨损占整个磨损总量的50%,故越来越多的研究者对抗磨料磨损的材料进行了一系列的研究。
-
The experimental results indicate that the particle size distribution has great influence on the attrition behavior of the catalysts tested, and a mixed attrition mechanism consisting of abrasion and fragmentation is identified for all the catalysts in terms of attrition loss rate evaluation, after-attrition morphology characterization and particle size distribution analysis. It is shown that the attrition of particles was found to evolute following Gwyn's kinetic model and the difference of attrition mechanism of various particles can be categorized with parameters of the Gwyn equation.
实验结果表明,不同粒径的催化剂颗粒具有不同的磨损行为;所有测试催化剂的磨损均由表面剥层磨损和体断裂磨损组成的混合磨损机制所支配;磨损的发展过程符合Gwyn磨损动力学方程,不同颗粒磨损规律的差别可由Gwyn方程的各参数来描述。
-
Wear and corrosion involve mechanical and electrochemical mechanisms, and the combined action of these mechanisms often result in significant mutual reinforcement. To measure the effect on wear-corrosion resistance of the chemical and abrasion wear separately at the same time, wear-corrosion synergism rate is selected to indicate the nature and degree of the chemical and abrasion wear.
腐蚀磨损是同时涉及力学因素和电化学因素的复杂的材料的流失过程,通常条件下,腐蚀磨损不是纯磨损和纯腐蚀的简单叠加,还有两者间的协同作用,为定量描述腐蚀与磨损的促进程度、进一步完善腐蚀磨损机理,本文利用腐蚀磨损协同作用率值的大小来分析腐蚀和磨损的交互作用程度,结果表明:本文制备的镀层,在5%H_2SO_4溶液中腐蚀磨损时,机械磨损是造成镀层表面材料流失的主要原因,腐蚀和磨损的协同作用为次要因素。
-
And, finally, the results of wear tests show that in comparison with undeformed specimens the weight loss of deformed and boronized specimens is much smaller and the time for transition from slight to severe wearing is greatly delayed.
最后,磨损试验结果表明,与非形变试样相比,形变渗硼试样的磨损失重明显减小,由轻微磨损到剧烈磨损的转变时间推迟。
-
Figure 7-13 Creep, wear, and difficulty in roentgenographically determining cup wear. A, Roentgenographic findings in 66-year-old patient suggestie of cup wear compared with roentgenograms taken 9 years earlier .
图7-13。蠕变、磨损以及X线确定臼杯磨损的难点,B:66岁病人,与9年前所拍X线片比较提示臼磨损。
-
Secund abrasion is main format of abrasion about double-front-axle steering automobile and is different from secund abrasion caused by the parameter matching of the wheel location improperly.
双前轴转向汽车轮胎磨损的主要形式是偏磨损,这种偏磨损有别于车轮定位参数匹配不当时引起的偏磨损。
-
Under the three body abrasive wear, the cutting is main reason of wear of the hard materials (3M and 2M). It is an important wear form of material 4M and several austenitic manganese steel at high load condition. b. The plastic materials form the block debris after deforming many times, forming the block-shape debris is the major waar form of this kind of material under several given wear conditions.
在三体磨粒磨损条件下,切削是造成编号为2M和3M等硬质材料磨损的主要原因,也是4M和几种奥氏体锰钢在高载荷下磨损的重要形式;块状屑的形成是塑性较好的材料在各种磨损条件下磨损的主要形式。
-
It is considered that link wear speed on seal surface is proportional to the contacting pressure. The impacting of valve disk on valve seat is the important reason of abrasive wear, and the relative motion of disk is a main reason for errosion wear of pump valve. The cycles per minute is an important factor to influence the valve motion and the impact force.
结果表明,泵阀密封面联接磨损的磨损速度与密封面上的接触比压成正比,泵的冲次是影响阀盘运动规律及对阀座产生冲击的重要因素,泵阀产生磨粒磨损和疲劳磨损的主要原因是泥浆、阀盘和阀座的冲击,冲蚀磨损导致泵阀的刺蚀。
-
In the paper the author relates systematically the research fruits in the program of Research on Sand Slurry Abrasion Mechanisms of Dredging Conditions and New Wear-Resistant Materials. The main contents and innovations are listed as follows.Summarized and analyzed are the wear researches and developments, and the methods of increasing materials wear-resistance. From the viewpoint of the characteristics of two-phase liquid sand slurry wear, combined with the examination and study on easily damaged workpieces, the wear failures basic rules are pointed out, of the pump shell and the cutter-piece on service, and the general principles of material wear-resistant designs put forward. The sand slurry abrasion tester has been designed and developed which can simulate general dredging conditions. Summarized and presented are the position-exchange measuring method of sand slurry abrasion test and the experiment specification of sand slurry wear test of dredging conditions.
文中系统论述了作者在疏浚工况泥沙磨损机理及其耐磨新材料课题研究中的工作成果,主要研究内容和创新点如下:总结分析了磨损研究动态和提高材料耐磨性的方法;从两相流泥沙磨损的特点出发,结合对失效易损件的考察研究,分析指出了现役泥泵壳和绞刀片磨损失效的基本规律,提出了材料耐磨损设计的基本思想;设计研制了能模拟疏浚工况的泥沙磨损试验机,总结提出了泥沙磨损试验换位测试法和疏浚工况泥沙磨损试验规范。
-
Roll wear is a factor difficult to determine and there is no suitable theoretical model till now In this paper,the theoretical model of roll wear is established from the view of tribology,and the roll wear on finishing train of 2050 CVC hot strip mill has been measured The calculated results agree well with the measured,so the model for roll wear is of important significance for shape control
轧辊磨损是当前生产中难以定量确定的因素,磨损预报至今尚无精确的理论模型可利用。本文从摩擦学原理出发建立了轧辊磨损的理论模型,并对宝钢 2 0 5 0 CVC热连轧机精轧机组的轧辊磨损量进行实际测量,计算结果与实测值吻合较好,对提高磨损预报精度、提高板形控制技术水平具有重要意义
- 更多网络解释与磨损的相关的网络解释 [注:此内容来源于网络,仅供参考]
-
abraded culet:磨损的底尖
aborigines [复]土著居民 | abraded culet 磨损的底尖 | abraded edge 磨损的晶棱
-
worn-out engine:磨损的发动机,用坏的发动机,不能再用的发动机
worn-out in service 在使用中磨损的 | worn-out engine 磨损的发动机,用坏的发动机,不能再用的发动机 | worn-out 磨损了的;用坏了的;陈旧的,破烂的;耗尽的,没有用的;衰弱的
-
worn-out parts:磨损的零件
worn-out surface 磨损表面 | worn-out parts 磨损的零件 | worn-out in service 在使用中磨损的
-
worn:磨损的
worn parts 磨损部件 | worn 磨损的 | wornout 穿旧的
-
attrite:磨损的
attricist 人员损耗 | attrite 磨损的 | attrited 磨损的
-
attrite:磨损的, 削弱的 磨损以便使.变小
attrit | 消耗,削弱 (军事上)消耗敌人的行动消耗战 | attrite | 磨损的, 削弱的 磨损以便使.变小 | attrited | 磨损的, 磨坏的
-
attrited:磨损的
attrite 磨损的 | attrited 磨损的 | attrition 磨擦
-
attrited:磨损的, 磨坏的
attrite | 磨损的, 削弱的 磨损以便使.变小 | attrited | 磨损的, 磨坏的 | attrition medium | 研磨介质
-
worn-down:磨损的
worn-down with use 在使用中磨损的 | worn-down 磨损的 | worn engine 磨损的发动机
-
worn-down with use:在使用中磨损的
worn-in 磨合,走合 | worn-down with use 在使用中磨损的 | worn-down 磨损的