- 更多网络例句与电弧炉相关的网络例句 [注：此内容来源于网络，仅供参考]
-
Based on the analysis of three-dimensional power conductor for DC arc furnace, the electric arc deflection model was set up and the control system of the arc direction was configured. According to the bus bar distribution at the bottom electrodes cooled by water, the arc direction control principle and its configuration were described, The simulation results show that the control system can restrain the electric arc deflection and control the arc direction.
在分析直流电弧炉三维导体布置的基础上，建立了直流电弧的偏工以此作为电弧位置控制的依据，针对水冷钢棒式底电极型的直流电弧炉，阐述了其电弧位置控制的原理和系统组成，并进行了仿真研究，结果表明控制系统可以有效地纠正电弧的偏向总是并可控设定点自由控制电弧以位置。
-
This paper provides a simple, feasible way to simulate the electric characteristic of electric arc furnace.
在模拟电弧炉电弧电气特性上探索出了一种可行的、简单的方法，能够模拟出和实际电弧炉主电路相一致的外特性，能够满足电弧炉电弧控制试验的需要。
-
The effects of control parameters circuit characteristics and different smelting stages on electric arc impedance are considered.
该模型考虑了电弧控制参数、线路特征及冶炼不同阶段对电弧阻抗的影响，用Matlab实现了电弧炉模型的仿真，进行了谐波分析的仿真研究，给出了电弧电压与电弧电流的仿真波形图。
-
After having compared the cupola furnace with electric arc furnace on the characteristics of the process of producing spheroidal graphite cast iron steel ingot module and their application effects, the results show that it will prolong the life of steel ingot module and improve the quality of steel ingot by applying arc furnace to melt spheroidal graphite cast iron steel ingot module.
电弧炉技术在球墨铸铁钢锭模生产上的应用赵海兵任元和李梅曹志张涛摘要将冲天炉和电弧炉这两种生产球墨铸铁钢锭模的工艺特点及应用效果进行对比，结果表明，采用电弧炉冶炼球墨铸铁钢锭模能够提高钢锭模使用寿命，改善钢锭质量。关键词球墨铸铁模耗A
-
A non-linear reactance model and an electric principle diagram of power supply for the 90tCONSTEEL EAF at SISG are constructed,based on the data on-site gathered with the furnace,and thus a more rational power supply curve is worked out.
根据现场实测数据，确定韶钢90 tCONSTEEL电弧炉的非线性电抗模型和电气圆图，从而制定了较合理的供电曲线。文中着重讨论了建立电弧炉电抗模型的原则、方法及其对制定合理供电曲线的作用
-
It is analysed that it is necessity,feasibility that Zhuzhou Smelts adjust the structural of raw materials about zinc smelts.And it propose that the electric arc furnace dust supplies for zinc resource two times , thus solve the problem that the zinc smelts raw materials insufficient in supplely.
提出了株冶应根据电弧炉烟尘等二次锌原料与中性浸出渣化学组成性质上十分类似的特点，采用挥发回转窑处理电弧炉烟尘等二次锌原料，从而解决锌冶炼原料供应不足的问题。
-
Aiming at the tristep method smelting process of "electrical arc furnace+multifunction converter+VOD" for stainless steel, and centering about the dephosphorization during the process, the theoretical analysis and calculations have been carried out for the feasibility of several important links in the process chain (including desiliconization and chromium conservation in EAF, and simultaneous dephosphorization and desulfurization in ladle ) in the view of melting thermodynamics.
针对&电弧炉+多功能转炉+VOD&三步法不锈钢冶炼工艺，以脱磷为主线，从冶金热力学的角度对流程中涉及的几个重要工艺环节的可行性(包括电弧炉去硅保铬、铁水包同时脱磷脱硫等问题)进行了理论分析和计算。
-
In the previous issue on the basis of the theory, structure based on the 8051 MCU EAF arc length waveform generator system, through a link on the waveform of the hardware and software to achieve a further wave of EAF the main circuit hardware simulation.
本课题在前人的理论基础上，构造了基于8051单片机的电弧炉弧长波形产生系统，通过对波形的发生环节的软硬件实现产生波形进而对电弧炉主电路的硬件进行仿真。
-
Especially, it pointed out that the design of modern steel-making electric arc furnace short net should base on three-phase balance, delta connection should be implemented inside the transformer, the section of conductor should be selected according to the density of economy electric current and the number of connected points of short net should be reduced.
围绕现代电弧炉供电及工艺方面的改进，提出短网设计与改造要点，特别指出：现代炼钢电弧炉短网的设计要以三相平衡为主，变压器的二次出线三角形封口要在变压器内实施，短网导体截面要按经济电流密度选取，以及尽量减少短网导体联接处。
-
On the basis of analyzing running condition arc furnace system and researching characteristics of dust remover of arc furnace, taking the application of Harsvert-A in dust removing transformation of steelworks as an example, successful application of high-voltage frequency conversion technology on dust removing system of arc furnace in steelworks is introduced.
在分析了电弧炉设备的运行现状和研究了电弧炉除尘系统特点的基础上，通过Harsvert-A型高压变频器在某炼钢厂除尘系统改造中的应用实例，介绍了高压变频技术在炼钢厂电弧炉除尘系统中的成功应用。
- 更多网络解释与电弧炉相关的网络解释 [注：此内容来源于网络，仅供参考]
-
acheson furnace：艾其逊炉(制碳化矽用电弧炉)
acetylene tetrabromide 四溴化乙炔 | Acheson furnace 艾其逊炉(制碳化矽用电弧炉) | Acheson process 艾其逊法(用电弧炉制碳化矽)
-
Acheson process：艾其逊法(用电弧炉制碳化矽)
Acheson furnace 艾其逊炉(制碳化矽用电弧炉) | Acheson process 艾其逊法(用电弧炉制碳化矽) | acicular cast iron 针状铸体
-
electric arc：电弧炉
rotary hearth ~转底炉 | electric-arc ~电弧炉 | electric ~电炉
-
electric arc furnace：电弧炉
到了二十世纪初,随著发电技术渐趋成熟,开始改用电弧炉(Electric Arc Furnace)来炼钢,这个方法实际是结合了贝塞麦炼钢法和平炉炼钢法,不但能够制成用途的特种钢而且大幅提升生产率.
-
arc process：电弧炉炼钢
arc potential || 电弧电位,电弧电压 | arc process || 电弧炉炼钢 | arc production furnace || 电弧熔炼炉
-
electric arc furnace electrode regulator system：电弧炉电极调节系统
电弧炉主电路:electric arc furnace circuit | 电弧炉电极调节系统:electric arc furnace electrode regulator system | 真空自耗电弧炉:vacuum arc remelting furnace
-
arc furnace：电弧炉
直接还原铁主要是用于炉内装料部分,是当电弧炉钢铁生产者在其废钢送料时需要高 ...使用电弧炉(arc furnace)制作磁性物质. (一) 利用钻石切割器,切割适量所需之金属元素. (二) 将金属元素置入电弧炉内,
-
direct arc furnace：直接电弧炉
direct analog computer 直接模拟计算机 | direct arc furnace 直接电弧炉 | direct bearing 导向轴承
-
direct arc furnace：直接式电弧炉
direct action circuit 直接动诅路 | direct arc furnace 直接式电弧炉 | direct axis component 直轴分量
-
vacuum arc furnace：真空电弧炉
vacuum arc deposition 真空电弧镀膜 | vacuum arc furnace 真空电弧炉 | vacuum arc melting 真空电弧熔化