英语人>词典>汉英 : 热脆性的 的英文翻译,例句
热脆性的 的英文翻译、例句

热脆性的

词组短语
hot short
更多网络例句与热脆性的相关的网络例句 [注:此内容来源于网络,仅供参考]

The influences of alloying elements on expansibility and ductility of the gray cast iron were investigated.

研究了在磷生铁基体中添加微量元素Sb、Bi、Cu对改善磷生铁的热膨胀性能及脆性的影响规律。

Measuring conditions were analyzed,such as lamp current,slit width,air and acetylene flow.

铜是钢中的有害杂质,能使钢产生热脆性,破坏钢的焊接性能。

Results obtained show that the range of quasi-solid is equivalent to the range of hot brittleness, and B, Ti as well as mischmetal all lower the quasi-solidus and enhance the strength around solidus and the increase rate of strength of the alloy.

研究结果表明,合金的准固态区即热脆性区,B,Ti和稀土都能降低合金准团相线温度,提高强度增长率和准固相线附近的强度,稀土的作用强于B和Ti。

Therefore, the roll surface is extremely hard and brittle and it is thermally unstable.

因此,辊子表面有极高的硬度、脆性及热不稳定性。

As the brittleness of low-k material,the traditional wire bonding parameter often lead to die pad crack or Au-AL matter bad;after used low-k material,die size,die pad opening and die pad pitch change to more little,wire change to lengther and density change to more higher,it\' s new challenge for molding and wire bonding;at the same time, low-k material also require to control the thermal stress in package.

由于低介电常数材料的脆性,传统的引线压焊参数设置将会导致焊盘碎裂以及金铝化合物不良;由于使用低介电常数材料后,芯片尺寸、压焊区域和压焊间距进一步减小,金线压焊长度和密度大大增加,这就为压焊和模塑提出了新的要求;同样由于低介电常数材料的应用,对封装体内部的热应力的控制也提出了更高的要求。

Gold came from the mantle and/or from remelted crust, while large, deep-cut faults and passageways of the remelted magmas provided possibility of transportation of the hydrothermal fluids, and brittle, brittle-ductile overlapped faults developped at the moderate-shallow levels of the mantle plumes, and related decollements, provided ideal sites for the precipitation of hydrothermai fluids.

金主要来自地幔及重熔地壳,深大断裂及重熔岩浆通道为成矿热液的迁移提供了有利条件,中浅层次的幔枝隆起及外围滑脱带中的脆性、韧—脆性叠加断裂为矿液提供了沉淀场所。

High carbon and high molybdenum high speed steel has ...

高碳高钼高速钢具有硬度高、红硬性和耐磨性好等特点,但铸造高速钢脆性大,采用RE -Mg -Ti复合变质处理,可以改变共晶碳化物的形态和分布,使铸造高速钢冲击韧性提高 86 。2 %,热疲劳抗力和耐磨性也明显改善。

According to the emphatic analysis of processing,the 4 kinds of laser damage-free cutting methods,including traditional optimized parameter method,laser multiple-pass cutting,laser cutting with controlled fracture by stress guiding method and aided laser cutting method,are summarized.

介绍了硬脆性陶瓷激光切割技术研究的若干新进展,着重从工艺角度系统地分析总结了激光加工陶瓷减少热损伤的4大类型:传统工艺的优化参数法、多道切割法、应力引导控制裂纹切割法以及辅助切割法。

The results show that the reason of pockmarks is significantly related to nonmetallic inclusions of Si,Al and Ca.

结果表明,其产生的原因与Si、Al、Ca形成的脆性夹杂物有关,在金属塑性变形及冷、热加工过程中,由于受到拉应力作用,脆性夹杂物碎裂后脱落而造成。

Iron and steel with too much sulfur are red-short.

含硫过多的铁和钢都是热脆性的

更多网络解释与热脆性的相关的网络解释 [注:此内容来源于网络,仅供参考]

hot-tempered:性急的

hot-short 热脆性的 | hot-tempered 性急的 | hot-water bag 热水袋

hot shortness:红脆性,热脆性

hot short 热脆,热脆的,热脆性的,红脆的 | hot shortness 红脆性,热脆性 | hot shot 过热

weldability:焊接性

如果钢材中硫含量太高,则会形成FeS,FeS是低熔点夹杂物,当钢材温度高於985℃时,此低熔点夹杂物先熔融而形成晶粒间液态薄膜,以致造成热脆性(Hot Shortness). (3) 随著含硫量增加,钢材的焊接性(weldability)会随著下降.

red-short:热脆

赤热的 red-hot | 热脆 red-short | 热脆性;热脆 red-shortness