润滑油孔

基本解释 (translations)

oilhole

与润滑油孔相关的网络例句 [注：此内容来源于网络，仅供参考]

Pivoting stainless steel spray lance (1050 mm), High-pressure hose 10 m, Dirt Blaster, Triple nozzle with touchless changeover, 0°/25°/40

带10米高压管的伺服引发枪，带发光二极管显示的电机保护系统，1050毫米轴向旋转不锈钢喷枪杆，6升清洁剂箱，润滑油显示窗，大水流量，压力控制开关，凯驰专利高压管防缠绕设计，三孔无接触旋转喷嘴0度/25度/40度，强力旋转喷嘴。

Pivoting stainless steel spray lance (1050 mm), High-pressure hose 20 m, Integral high-pressure hose, Dirt Blaster, Triple nozzle with touchless changeover, 0°/25°/40

伺服引发枪，带发光二极管显示的电机保护系统，1050毫米轴向旋转不锈钢喷枪杆，6升清洁剂箱，润滑油显示窗，大水流量，压力控制开关，凯驰专利高压管防缠绕设计，三孔无接触旋转喷嘴0度/25度/40度，带卷轴的20米高压管。

There is one oil groove in the bronze bushing, where lubricant can flow into the axis from the oilhole on the cap of housings.

轴瓦内表面的不承担载荷部分开有油槽，润滑油通过进油孔和邮沟流进间隙。

The assembly of journal and plain bearing liner space is too little, force of organic still oil pressure is small it is the crucial index that affects lubricant result, make lubricate because of lacking engine oil between crankshaft and plain bearing liner and bite dead invalidation, include to be pulled badly, lack lube, layer of alloy of dry attrition generation is fused, grind sliding surface to did not maintain the oily film of certain ply, and all sorts of local overload exhaustion are destroyed, cavitation erosion and V form are destroyed etc, through technology of him director diesel locomotive old experience reachs the analysis of pair of its breakdown reasons, put forward precautionary measures especially. As a result of,the burns caustic mechanism plain bearing liner to burn caustic mechanism of 1 plain bearing liner is the lube film burst between journal and plain bearing liner, cause plain bearing liner and crankshaft generation clash, below high temperature, high pressure and high rotate speed, the wear-resisting alloy layer of plain bearing liner wears away prematurely or fuse, cause plain bearing liner and crankshaft to stick thereby bite, can make the steel back of plain bearing liner and Kong Zhong produces whirligig, inlet port is jammed, carry on the back by steel again with the friction of aperture causes high temperature to make plain bearing liner burned-out further, can cause bolt to break off, happen swing a malign accident that pounds cylinder body of bad internal-combustion engine.

轴颈和轴瓦的装配间隙太小，还有机油压力低是影响润滑效果的关键指标，使得曲轴和轴瓦之间因缺少机油润滑而咬死失效，包括严重拉伤，缺少润滑油，干摩擦产生合金层熔化，磨滑面没有保持一定厚度的油膜，以及各种局部过载疲惫破坏，气蚀和V形破坏等，通过本人主管内燃机车技术多年经验及对其故障原因的分析，特提出预防办法。1轴瓦的烧损机理轴瓦烧损的机理是由于轴颈和轴瓦之间的润滑油膜破裂，导致轴瓦和曲轴产生摩擦，在高温、高压和高转速下，轴瓦的耐磨合金层过早地磨损或熔化，从而引起轴瓦和曲轴粘咬，会使轴瓦的钢背和座孔中产生旋转运动，进油孔被堵塞，再由钢背和座孔的磨擦进一步引起高温使轴瓦烧坏，并会造成螺栓折断，发生甩出捣坏内燃机缸体的恶性事故。

There are oil groove or holes on the outer ring which make HSB needle roller bearing easy for lubricating.

外圈上的油槽和油孔使HSB-滚针轴承加润滑油更加方便。

Cleaning the nose spindle hole and the dust on the machine spindle, on a little oil to make installation smooth.

清洗机头主轴孔和成型机主轴上的灰尘，上少许润滑油，使安装顺畅。

与润滑油孔相关的网络解释 [注：此内容来源于网络，仅供参考]

oil passage：润滑油孔

oil pan 油盘;切屑盘 | oil passage 润滑油孔 | oil patch 含油岩屑;油斑;石油勘探、开采和油田管道铺设所涉及的地域;油田

oil booster pump：增压油泵

oil booster pump 升压油泵 | oil booster pump 增压油泵 | oil bore 润滑油孔