气开关

词组短语

air cock

与气开关相关的网络例句 [注：此内容来源于网络，仅供参考]

This article presents the corresponding measures on the adjustment of samplc pressure,temperature of thermotank ,flowrate of carrier gas,length of measuring cycles and determination of keeping time of sample compositions;the influence of sampling,columns interchange,backflush and time change of compensation valvc to the measurement and analysis and the solutions to bo adopted.

介绍 PGC3 0 2在线气相色相谱仪因原进口色谱柱劣化，换用国产色谱柱后，在调试过程中，样品压力、恒温箱温度、载气流量、测量周期长短、样品各组分保留时间的确定，采样、柱切、反吹、平衡阀门开关时间的改变对测量分析的影响及解决办法。

But ECT technology has the following characteristics: 1 the measured capacitance and its change induced by the measured material concentration variation are very small, but the stray capacitances of co-axial screening cable and CMOS switches are relative very large, so the capacitance detecting is easily affected by the stray capacitances, 2 the electric fields in the sensors detecting region is affected by the permittivity distribution, non-uniformity of the space responsive sensitivity is very high, and the image reconstruction is undetermined.

但由于ECT技术中，首先所检测的微电容量及其因物流相含率的变化所引起的变化量很小，而由相关的连接同轴屏蔽电缆与切换CMOS开关所引入的杂散电容远远大于测量电容，微电容的测量容易受杂散电容等的影响；其次，多电极电容传感器测量区内的电场受介质分布的影响，且测量区内的空间响应灵敏度极不均衡，其影响图像重建的不确定性；其三，ECT中的图像重建，由于其是一个欠定问题的求解，在迭代求解方法中，迭代的初值影响迭代过程收敛到近似解的速度；其四，对于气/固两相流应用而言，由于ECT系统在线标定的难以实现，管壁磨损等因素的影响制约该技术应用于生产工艺中气/固两相流的长期连续检测。

Will manually, auto-switch to automatic, so that exsufflation switch exsufflation State, press the vacuum button T1, at which point the exhaust from the aliquation exposure done automatically.

不兵手不静、自不静开关不扎到自不静状况，让排气开关处于排气状况，按不静抽真空按钮T1，此时从呼气曝光排气自不静达成。

Main products: Series of Amorphous Silicon, monocrystalline silicon, polycrystalline silicon solar panels, solar intelligent controller, solar energy-saving lights, solar charger, solar mobile phone charger, solar lawn lamp, solar fan cap, full-function digital display 12A-Responder Knowledge Contest, Quiz answer in scoring device, the game scoring device, automatic water level controller, automatic rang the bell device (which can work 84 times / day), KD301, when microcomputer automatic control, and rang the bell device, KD302 microcomputer light control, time control switch, KD303 AC-DC dual-use micro-computer radio, rang the bell device, KD304 microcomputer AC-DC dual-use device to play Bell, KD - 18 multi-channel Pager, efficient electronic fishing devices, catch devices, infrared alarm, series inverter, the campus radio controller, smart, laser pointer, program-controlled telephone exchanges, series refrigeration components, series solenoid valve, Series DC lamp, series power hand-lamp, series of photoelectric switches, series of mercury switches, reed pipe series of wet, dry reed pipe, the first series of semiconductor gas, series core, magnetic ring, magnetic tank, ultrasonic transmitting and receiving the first, series fool Wang amplifier, series inverter module, push the module 2436, and so.

主要产品：系列非晶硅、单晶硅、多晶硅太阳能电池板，太阳能智能控制器，太阳能节能灯，太阳能充电器，太阳能手机充电器，太阳能草坪灯，太阳能风扇帽，数码显示12A―全功能知识竞赛抢答器，知识竞赛抢答记分器，球赛记分器，全自动水位控制器，全自动打铃器(可工作84次/天)，KD301微电脑自动时控、打铃器，KD302微电脑光控、时控开关，KD303微电脑交直流两用广播、打铃器，KD304微电脑交直两用打铃器，KD--18多路呼叫器，高效电子捕鱼器，捕器，红外线报警器，系列逆变电源，校园智能广播控制器，激光教鞭，程控电话交换机，系列制冷组件，系列电磁阀，系列直流灯，系列发电手灯，系列光电开关，系列水银开关，系列湿簧管、干式舌簧管，系列半导体气敏头，系列磁芯、磁环、磁罐，超声波发射接收头，系列傻瓜王功放，系列逆变模块，推动模块2436等等。

According to the request of adopting advanced technology, the main designing has such contents as below:⑴ Designing the two-fluid nozzle that is based on the theory of air-atomize spraying.⑵ Designing and choosing the type of the axial fan that is used to supply assisted airflow to waft droplets that comes from nozzle.⑶ Designing the swaying outfit that can rotate the spray assembly at a speed and inside a angle in order to satisfy the spray request of different crops, different planting states and improve the uniformity of distribution, the deposition of droplet. Here, we select TYV type reduction gear motor to adjust the swaying speed and use course switch to adjust the swaying angle.⑷ Designing the lift outfit that can adjust the height of the spray assembly to satisfy the request of the crops of different tallness, different spraying range. Here, we select cylinder as the main component that can be used as kickstand and controlled easily.⑸ Designing the switch of the power supply that is put out of the greenhouse in order to prevent worker from poisoning. After the mist sprayer being made, the experiment is made to test the function of the greenhouse mist sprayer fully.

根据采用先进施药技术的要求，本研究的设计内容主要有：⑴采用气液两相流喷雾技术，基于气力雾化原理，设计双流体喷头；⑵采用辅助气流输送雾滴，气流源为风机，对风机进行设计、选型；⑶为满足不同作物、不同栽培情况及提高雾滴分布均匀性、沉积性的施药要求，设计能带动喷射部件在一定角度内、以一定转速的旋转摇摆机构，本研究选用调速电机调节其摇摆速度，并利用反向行程开关调节其摇摆角度；⑷为满足不同高度作物、不同射程的施药要求，设计能调节喷射部件高度的升降机构，这里选用气缸为主要构件，既可以起到整机支架的作用，又可方便进行升降、固定控制；⑸设计行程开关的控制电路以及整机的控制系统。

The results showed that sevoflurane was the most prevalent volatility halogenate anesthetics and had the highest concentration at sampling areas. All study hospitals exceeded the exposure limit for halogenate anesthetics (2ppm) recommended by NIOSH (National Institute for Occupational Safety and Health).The median level of N2O at the two medical centers was 1.87 ppm. Although regional hospitals seldom use N2O, its concentration was very high (median 120.85 ppm).

结果显示，Sevoflurane为使用最多之挥发性卤化麻醉剂，环境浓度亦最高，各医院均有高於NIOSH对於单一卤化麻醉剂暴露建议值(2ppm)的情形；医学中心笑气浓度之中位数为1.87 ppm，然区域医院虽极少使用笑气，环境中位数浓度高达120.85 ppm，有管路或开关阀泄漏之可能性。

Box in the settings: melting Plug and plug, air switches, light switches, low-voltage lamps, power supplies, single phase power supply, etc.?

电箱边撤销：熔塞及熔塞座、不满气开关、照明开关、低不抬灯、电源、单相电源等。

The introductive robot arm of this text can output two lines pulses by the PLC, driving the horizontal stalk, and the perpendicular stalk to drive the electrical engineering actuator respectively, to control the robot arm precision of the horizontal stalk and perpendicular stalk at the fixed position, tiny move switch input the position signal to the PLC.The direct current motor drags along to begin the claw and bedrocks to revolve, the position signal from revolve the code dish and near to the switch feedback to host of PLC;The electromagnetism valve control the machine hand open and close, thus carry out the function of the machine hand precision work.

本文介绍的机械手是由PLC输出两路脉冲，分别驱动横轴、竖轴步进电机驱动器，控制机械手横轴和竖轴的精确定位，微动开关将位置信号传给PLC主机；直流电机拖动手爪和底盘旋转，位置信号由旋转码盘和接近开关反馈给PLC主机；电磁阀控制气开阀的开关来控制机械手手爪的张合，从而实现机械手精确运动的功能。

The hybrid induction motor includes a housing; a stator installed in the housing and having a stator core portion and a stator coil portion; a rotor coupling body having a rotary shaft rotatably installed in at the housing, a cage rotor portion rotating integrally with the rotary shaft, and a permanent magnet rotor portion coupled to a circumference of the cage rotor portion with a certain air gap so as to be freely rotatable with respect to the rotary shaft; and a reverse rotation preventing switch, when the rotary shaft rotates reversibly, coming in contact with the permanent magnet rotor portion which is moved along the shaft by thrust generated by the rotor coupling body and cutting off power being supplied to the stator coil portion.

公开了一种混合式感应电机。所述混合式感应电机包括：壳体；安装在壳体中并且具有定子铁心部分和定子线圈部分的定子；篆字联接体，具有可旋转地安装在外壳中的旋转轴、整体地与旋转轴一起旋转的鼠笼式转子部分，以及永磁体转子部分，该部分以一定气隙连接到鼠笼式转子部分的周围以可相对于旋转轴自由旋转；以及防止反转开关，当旋转轴反转时，与永磁体转子部分形成并且切断提供给定子线圈部分的电源，其中当旋转轴反转时，转子联接体产生推力，通过该推力永磁体转子部分与反转防止开关相接触。

The paper describes the selection principle of primary schemes for C-GIS and determines the general structure arrangement by comparing different elements and box structure, analyzes the insulating characteristics of SF6 gas and calculates the SF6 gas clearance and along surface insulation. It puts forward the factors that should be considered and strength analysis methods when designing gas chamber structure and analyzes the reasons of influencing the temperature rise of gas chamber and offers the ways of radiating. The vacuum circuit breaker and three-position disconnector are designed for C-GIS and special micro-computer controller for the three-position disconnector is developed. On the basis of new type sensors, suitable control and protection system for C-GIS is suggested. The type test items for C-GIS and its internal elements are introduced to prove that the development is successful.

本文论述了C-GIS产品的一次接线方案选择的原则，在比较各种元件构成及箱体结构的基础上确定了产品的总体结构；分析了SF6气体的绝缘特性，并对SF6气体间隙及沿面绝缘进行了工程计算；阐述了气室设计应考虑的主要因素及强度分析方法，对影响气室温升的原因进行了剖析，并提出散热措施；介绍了C-GIS用真空断路器及三工位隔离开关的设计技术；运用微机技术开发了专用的三工位隔离开关控制器；在阐述新型传感技术的基础上，提出了适用于C-GIS的控制和保护系统；简述了C-GIS产品及内部元件的型式试验项目，证明本产品的研制是成功的。

与气开关相关的网络解释 [注：此内容来源于网络，仅供参考]

air cock：气开关

air cleaner 空气净化器 | air cock 气开关 | air collector 空气收集器

Air relief cock：放气旋塞,放气开关

Air regulating valve 空气调节阀 | Air relief cock 放气旋塞,放气开关 | Air required for combustion 燃烧必要空气量

air tank drain cock：气箱排放塞[开关]

air tack cement | 封气粘液 | air tank drain cock | 气箱排放塞[开关] | air tank | 氧气筒

air horn valve：气喇叭阀

air horn switch;气喇叭开关 | air horn valve;气喇叭阀 | air hose;送气软管

air horn switch：气喇叭开关

air horn solenoid valve;气喇叭电磁阀 | air horn switch;气喇叭开关 | air horn valve;气喇叭阀

air pressure switch：气动开关

air-pressure duct 压缩空气管道 | air-pressure switch 气动开关 | air-proof 气密的

fuzzy switching function：模糊开关函数

foot-switch 脚踏开关 | fuzzy switching function 模糊开关函数 | gas kitchen 气灶

thermal time switch：温控[热敏]定时开关

thermal system 进气加热装置.恒温进气系统 | thermal time switch温控[热敏]定时开关 | thermal vacuum switch温控真空开关

thermal time switch：温控定时开关

thermal system 进气加热装置.恒温进气系统 | thermal time switch温控定时开关 | thermal vacuum switch温控真空开关

air escape cock：放气开关

air escape ==> 漏气,泄气 | air escape cock ==> 放气开关 | air evacuation valve ==> 排气阀