- 更多网络例句与止推轴承相关的网络例句 [注：此内容来源于网络，仅供参考]
-
A set of theoretical models based on the EHDL problem of self-acting foil bearing are solved by a program with finite element method, and the calculation results of static performance are discussed.
本文采用基于弹性流体润滑问题的理论模型的有限元方法程序对弹性支承箔片动压气体止推轴承进行了求解，并就轴承结构参数、位置参数及运转参数对轴承稳态性能的影响进行了求解。
-
A set of high-speed on-line dynamic data acquiring hardware system and correlation software in Windows operating system was developed for the rig of self-acting thrust gas bearing. A set of analyzing software of experimentation data was developed.
为了进行试验研究，本文开发了一套在线高速动态数据采集硬件系统及基于Windows平台下的相关软件，同时还开发了一套功能强大的止推轴承数据分析和处理软件。
-
Valve shaft uses thrust bearings and "O" shaped seal ring to reduce friction, and stuffing box's leakage problem is also solved.
阀杆采用止推轴承和"O"型圈密封，减少了开关时的摩擦力，解决了填料箱漏水问题。
-
This paper presents the method determining the reasonable WOB by the thrusting force analysis of the bearing section of transmission shaft section.
通过对传动轴止推轴承的受力分析，提出了合理钻压的确定方法。
-
Making the full use of the theoretical knowledge of FEA,contact mechanics and friction wear,and integrating with the research of other domestic and international scholar. Starting with analyzing working characteristics of journal bearing of roller cone bit, we finished the contact FEA of the journal bearing and the thrust bearing, using ANSYS software. The tolerance ranges of journal bearing of a roller cone bit are specially studied.
本文利用有限元、接触力学和摩擦学理论知识，同时结合国内外其它学者的研究，从分析牙轮钻头滑动轴承的工作特性入手，利用软件ANSYS完成了牙轮钻头中大、小轴承及止推轴承的接触有限元分析工作，对牙轮钻头滑动轴承的尺寸公差的取值，进行了专门的研究和探讨。
-
Valve shaft uses thrust bearings and "O" shaped seal ring to reduce friction, and stuffing box's leakage problem is also solved.
阀杆采用止推轴承和&O&型圈密封，减少了开关时的摩擦力，解决了填料箱漏水问题。
-
Reasons:(1) If metal friction sound is the turbocharger rotor-bearing or thrust bearing wear too much, turbocharger impeller and shell friction generated.
原因： （1）如有金属摩擦声，是增压器转子轴承或止推轴承磨损过多，叶轮与增压器壳摩擦而产生。
-
Rotary servo motor + ball screw up to 2 ~ 5μm, and the requirements of CNC-servo motors - even without coupling gap - thrust bearing - Cooling System - high-precision rolling guide - Nut Block - table closed-loop system as a whole transmission part to lighter, higher precision grating.
旋转伺服电机+滚珠丝杠最高达到2~5μm，且要求CNC-伺服电机-无隙连轴器-止推轴承-冷却系统-高精度滚动导轨-螺母座-工作台闭环整个系统的传动部分要轻量化，光栅精度要高。
-
Two hydros atic bearing configurations are suitable for combined radial and axial load depending on the particular requirement.
至于用向心轴承和止推轴承分别承受径向力和轴向力的轴承组合，一般并不称之为&联合轴承&。
-
By analyzing the model for magnetic suspension thrust bearing ,the math model of the system was established.
介绍了磁力轴承的主要特点及应用，并以一磁悬浮止推轴承模型作为研究对象，建立了系统的数学模型。
- 更多网络解释与止推轴承相关的网络解释 [注：此内容来源于网络，仅供参考]
-
pivot bearing：枢轴承,摆动支座,中心(轴尖)支承,立式止推轴承
piston pin bearing活塞销轴承 | pivot bearing枢轴承,摆动支座,中心(轴尖)支承,立式止推轴承 | plain-and -ball bearing滑动与滚动组合轴承
-
thrust bearing：推力轴承,止推轴承推力座
thermo-expansion compensation angular ball bearing热胀补偿向心球轴承 | thrust bearing推力轴承,止推轴承推力座 | tin-copper-graphite bearing青铜石墨轴承
-
thrust bearing：推力轴承, 止推轴承
thermo-expansion compensation angular ball bearing热胀补偿向心球轴承 | thrust bearing推力轴承,止推轴承 | tin-copper-graphite bearing青铜石墨轴承
-
locating bearing：止推轴承,定位轴承
lignumvitae bearing层压胶木轴承 | locating bearing止推轴承,定位轴承 | lock nut bearing锁紧螺帽座
-
step bearing：立式止推轴承,踏板轴承,阶式止推轴承
steering worm sector bearing转向器扇形蜗轮轴承 | step bearing立式止推轴承,踏板轴承,阶式止推轴承 | straight roller bearing普通滚柱轴承
-
toe bearing：立式止推轴承
tip bearing枢轴承,枢支座 | toe bearing立式止推轴承 | top bearing上盖(顶盖)轴承
-
collar thrust bearing：环领止推轴承
环境负荷 environmental load | 环领止推轴承 collar thrust bearing | 环领轴承 collar bearing
-
plummer block bearing：架座,止推轴承
plane bearing平面轴承 | plummer block bearing架座,止推轴承 | pneumatic bearing空气轴承
-
double thrust bearing：对向推力轴承,对向止推轴承
double-threaded screw 双头螺旋 | double-thrust bearing 对向推力轴承,对向止推轴承 | double-wedge 菱形的,双楔形的
-
end thrust bearing：止推轴承
end shield bearing机油滤清器内盖头轴承 | end thrust bearing止推轴承 | end-mounted bearing(耙组)两端安装的轴承