- 更多网络例句与止动销相关的网络例句 [注：此内容来源于网络，仅供参考]
-
A bracket will be installed within the transmissions to assure that the park pawl shaft remains properly in position.
在变速器内安装保持架来确保驻车止动爪定位销处在正常位置。
-
If the cup plug is missing, the park pawl anchor shaft can move out of position under certain conditions.
如果该杯状固定塞脱落，驻车止动爪定位销可能在特定情况下滑移出正常位置。
-
Place handwheel (17) over stem adaptor (12), locating shear pin (28) into the slot on the handwheel.
把手轮(17)装到阀杆接头(12)上，再将剪销(28)放到手轮的槽中。用止动销(18)固定好。
-
Factory main production: ring, wave washer, saddle-type flexible gasket, C-type snap ring, dish washer, single-ear binaural, round nut with washer stop, both within and outside the teeth, the bearings folder, plum gaskets, flexible cylindrical pin , card ring, DIN standard ring and all kinds of custom pieces of red stretch.
本厂主产：挡圈、波型垫圈、鞍型弹性垫圈、C型卡环、碟形垫圈、单耳双耳、圆螺母用止动垫圈、内外齿、轴承夹、梅花垫圈、弹性圆柱销、卡圈、DIN标准挡圈及各类冲拉伸件定制。
-
Guide slots (108) in a guide sleeve (32) receive a stop pin (52) carried by a plunger shaft (48), and the slots (108) define two axially and circumferentially spaced lower stops (104, 106) for aspirating and dispensing strokes respectively.
在引导衬套(32)中的引导狭槽(108)装有止动器销(52)，该止动器销(52)装在柱塞杆(48)上，该狭槽(108)确定了两个轴向和周向间隔开的下部止动器(104、106)，分别用于吸取冲程和分配冲程。
-
The user presses one lobe (112) for an aspirating stroke to rotate the plunger shaft (48) in one direction and align the stop pin (52) with uppermost lower stop (104) for a relatively short aspirating stroke and the user presses the other lobe (114) for a dispensing stroke to rotate the plunger shaft (48) in the other direction and align the stop pin (52) with lowermost lower stop (106) for a relatively long dispensing stroke.
用户按压用于吸取冲程的一个凸耳(112)，以便使柱塞杆(48)沿一个方向旋转，并使止动器销(52)与用于相对较短的吸取冲程的最上面的下部止动器(104)对齐，而用户按压用于分配冲程的另一凸耳(114)，以便使柱塞杆(48)沿另一方向旋转，并使止动器销(52)与用于相对较长的分配冲程的最下面的下部止动器(106)对齐。
-
The Style X body design has special geometry and plate configuration to allow each plate to strike the stop pin in its center of percussion.
X类型阀体结构具有特殊的几何结构和阀瓣配置，使得每个阀瓣撞击在其撞击中心的止动销上。
- 更多网络解释与止动销相关的网络解释 [注：此内容来源于网络，仅供参考]
-
locking plate：止动片
locking pin 锁销 | locking plate 止动片 | locking pliers 大力钳
-
locking pawl：制动爪,止动掣子
locking knob (车门)锁止按钮 | locking pawl 制动爪,止动掣子 | locking pin 锁[定位]销
-
retaining pawl：止动爪
retaining nut 止动螺母 | retaining pawl 止动爪 | retaining pin 嵌件定位杆;定位销
-
balance whip pin：摆轮止销
balance wheel || (钟的)摆轮, (时计, 音箱等的)平衡轮 | balance whip pin || 摆轮止销 | balance whip spring || 摆轮止动簧
-
knuckle stop screw：关节止动螺钉
knuckle spindle ==> 转向节销,转向节轴,前轮轴=>前輪軸 | knuckle stop screw ==> 关节止动螺钉 | knuckle support ==> 关节支架,转向节支架
-
stop plate：(连接绞链销的)止动板
(连接绞链销的)开口销split pin | (连接绞链销的)止动板stop plate | 舱口盖封胶带hatchcover seal tape
-
stop plank：插板
stop pin ==> 挡料销,防转销,定位销,止动销,止销 | stop plank ==> 插板 | stop plate ==> 止动片板,盲板,挡板
-
valve stop pin：气门止动销
valve sticking 气门胶粘,气门杆发涩 | valve stop pin 气门止动销 | valve stroke 气门升程,阀门行程
-
wrist-pin brass wedge set screw：肘节销铜衬楔止动螺钉
wrist-pin brass wedge bolt ==> 肘销铜衬楔螺栓 | wrist-pin brass wedge set screw ==> 肘节销铜衬楔止动螺钉 | wrist-pin brass wedge washer ==> 肘节销铜楔垫
-
set screw spanner：止动螺钉扳手
set screw piston pin ==> 固定螺钉式活塞销 | set screw spanner ==> 止动螺钉扳手 | set screw wrench ==> 止动螺钉扳手