英语人>词典>汉英 : 横进给 的英文翻译,例句
横进给 的英文翻译、例句

横进给

基本解释 (translations)
infeed

更多网络例句与横进给相关的网络例句 [注:此内容来源于网络,仅供参考]

The maximal depth model for single-pass milling process, the depth and surface roughness for plane surface are established. The milled profile of a single-pass milling of the jet can be modeled as a cosine curve of the form. Therefore, the maximal depth model for single-pass milling is established which indicates the quantitative relationship between the AWJ single-pass milling depth and the milling parameters.

假设磨料水射流单次铣削时的工件横截面形状为余弦曲线,建立了磨料水射流单次铣削的最大深度模型,分析了水射流压力、磨料流量、靶距、喷嘴横移速度、横向进给量和喷嘴直径及材料性能参数对单次铣削最大深度的影响规律。

The introductive robot arm of this text can output two lines pulses by the PLC, driving the horizontal stalk, and the perpendicular stalk to drive the electrical engineering actuator respectively, to control the robot arm precision of the horizontal stalk and perpendicular stalk at the fixed position, tiny move switch input the position signal to the PLC.The direct current motor drags along to begin the claw and bedrocks to revolve, the position signal from revolve the code dish and near to the switch feedback to host of PLC;The electromagnetism valve control the machine hand open and close, thus carry out the function of the machine hand precision work.

本文介绍的机械手是由PLC输出两路脉冲,分别驱动横轴、竖轴步进电机驱动器,控制机械手横轴和竖轴的精确定位,微动开关将位置信号传给PLC主机;直流电机拖动手爪和底盘旋转,位置信号由旋转码盘和接近开关反馈给PLC主机;电磁阀控制气开阀的开关来控制机械手手爪的张合,从而实现机械手精确运动的功能。

Ordinary lathe knife rest vertical and crosswise enter, give sport to turn from main shaft round sport hang wheel transmit, with cross, enter give gearbox, drive, slip away board case by mere thick stick or guide screw, vertical to slip away the board, slip away board move sideways.

普通车床刀架的纵向和横向进给运动是由主轴回转运动经挂轮传递而来,通过进给变速箱后,由光杠或丝杠带动溜板箱,纵溜板,横溜板移动。

When the engine bed overloads, can cause the tool rest automatically to stop; Also may the hand operated tool rest move or the realization quick movement and so on.

此外,有些机床的溜板箱中还具有改变纵、横机动进给运动方向的换向机构,以及快速空行程传动机构等。

更多网络解释与横进给相关的网络解释 [注:此内容来源于网络,仅供参考]

cross cut saw:横锯

cross cut file 交纹锉 | cross cut saw 横锯 | cross feed 横进给

infeed:横切, 横进给

achromatic region (色度图的)无色区, 白区, 消色差区 | infeed 横切, 横进给 | photocomposer [印]照相排版机

infeed:横进给

infectwithadisease 染病 | infeed 横进给 | infeedcam 横进给凸轮

infeed:横进给,横切

infection point | 拐点 | infeed | 横进给,横切 | infeed accumulator | 进料活套塔

infeed grinding:横磨,切入磨法,横磨法,横向进给磨削

infeed conveyor 给料运输机 | infeed grinding 横磨,切入磨法,横磨法,横向进给磨削 | infeed method grinding 横磨法

infeed accumulator:进料活套塔

infeed | 横进给,横切 | infeed accumulator | 进料活套塔 | infeed grinding | 横磨法,切人磨法,横向磨削

Cross-feed slide:横进给刀架

6.Carriage 床鞍 | 7.Cross-feed slide 横进给刀架 | 8.Headstock 主轴箱

cross feed screw:横进刀螺杆

cross feed 横进给 | cross feed screw 横进刀螺杆 | cross fitting 四通接头

cross traverse feed:横向进给, 横向进刀

cross transfer conveyer || 横向运输机 | cross traverse feed || 横向进给, 横向进刀 | cross traverse gear || 横动装置

Cross feed traverse:横进给

Cross direction 横向 | Cross feed traverse 横进给 | Cross force 横向力