桥支座

词组短语

bridge seat

与桥支座相关的网络例句 [注：此内容来源于网络，仅供参考]

Additionally,the distribution rule of bearing forces is concluded through analysis of project example.

通过对工程实例桥的分析总结了支座反力的分布规律。

But most of their work are focused on the straight girder bridges.

但是他们的研究均是针对直线梁进行研究的，而对曲线梁桥的支座布置形式的研究较少。

In the course of the whole bridge researches, used a orthotropic unit instead of lead rubber bearing.

在整桥模型的计算中，可将铅芯橡胶支座用一个正交各向异性材料单元来替代。

The results show that the seismic response of curved beam bridge and the influence of curvature radius can be reduced by using lead rubber bearing.

结果表明：铅芯橡胶支座不仅可以有效地降低曲线梁桥的地震响应，还有助于减少曲率半径对曲线梁桥地震响应的影响。

The collapse of bridges due to unseating at intermediate hinges during earthquake emphasizes the need to provide an adequate number of restrainer s to limit the relative displacement between frames in a bridge with inadequate hinge seat width.

在地震中，由于桥联间伸缩缝处过大的变位会造成桥梁破坏，所以需要在支座宽度不足的伸缩缝间设置适当的限位器，以限制伸缩缝间的相对位移。

Fourthly, I have discussed the method to adjust torsion through presetting decentration of support abutment, and analyzed the influence on the superstructure of it.

再次，讨论了预应力曲线梁桥预设支座偏心调整扭矩的方法，分析了支座预偏心对上部结构内力的影响。

Based on the finite element method, a fresh and unique type of footbridge, a papilionaceous partial tied arch footbridge, was analyzed. The influences to the whole structure's stress behavior, displacements, vibration periods and mode shapes under parabola and arc arch axis were discussed. Different selections of support forms, such as longitudinal slide or longitudinal hinge, led to different behaviors on structure.

针对一种新型而特殊的蝶式部分系杆拱步行桥，基于有限元数值分析比较抛物线形拱轴线和圆弧形拱轴线对整个结构受力、变形、周期和振型的影响，揭示选用纵向滑动支座与纵向不动铰支座时给结构性能带来的不同结果，对结构拉索张拉力的控制给出建议。

In this paper we discuss the rea sonable structural form about curved girder bridges in high-speed railway.

本文讲述的是高速铁路曲线梁桥支座布置形式的一些研究工作和相关结论，主要包括支座布置形式和约束方式的影响。

The main contents and results of this paper are listed as follows:Based on the finite element analysis software ANSYS establish a bridge of three-dimensional mechanical model of CWR;Based on an actual project,calculate different conditions of three forms of bridge and research the reasonable removal scope of fastener;Research on the allowed lock temperature rail track construction of partial maintenance of range.By analyzing the result obtain the best way to replace the support of a bridge and the range of removal of the bearing and permission of rail temperature of construction.It supports some recommendations for the replacement of city construction maintenance.

本文主要研究内容为：基于有限元分析软件ANSYS建立了桥上无缝线路三维力学模型；依据某实际工程，分析计算了三种桥梁形式在不同顶升工况下的钢轨和扣件受力，研究了扣件的合理拆除范围；对维修后局部钢轨施工锁定轨温的允许范围进行了研究；分析得出了城轨桥梁更换支座施工的最佳顶升方式、扣件拆除范围和允许施工轨温，为城轨桥梁更换支座的施工维修提出了一些建议。

This paper explained the construction technology of the bearing replacement for quasi-continuous T-girder bridge and analyzed the causes of bearing disease.

本文着重介绍准连续 T型梁桥支座替换工程施工技术，并分析支座病害原因。

与桥支座相关的网络解释 [注：此内容来源于网络，仅供参考]

bearing：支座

我们先要知道什么叫做桥梁. 桥梁简称为桥,桥是一种架空的人造通道. 概括的说,桥梁由四个基本部分组成,即上部结构(superstructure)、下部结构(substructure)、支座(bearing)和附属设施(accessory).

rocker bearing：桥架)摇轴支座; (桁架)伸缩支座

ring-oiled sleeve bearing油环润滑式滑动轴承;油环式滑动轴承 | rocker bearing桥架)摇轴支座; (桁架)伸缩支座 | rod bearing杆轴承

rod bearing：杆轴承

rocker bearing桥架)摇轴支座; (桁架)伸缩支座 | rod bearing杆轴承 | roller bearing滚柱轴承

rod bearing：杆sunthai轴承

rocker bearing桥架)摇轴支座; (桁架)伸缩支座 | rod bearing杆sunthai轴承 | roller bearing滚柱sunthai轴承

substructure：下部结构

我们先要知道什么叫做桥梁. 桥梁简称为桥,桥是一种架空的人造通道. 概括的说,桥梁由四个基本部分组成,即上部结构(superstructure)、下部结构(substructure)、支座(bearing)和附属设施(accessory).

beam level deflectometer：杠杆弯沉仪

beam bridge 梁桥 | beam level deflectometer 杠杆弯沉仪 | bearing 支座

roller bascule bridge：滚动式竖旋桥

roller balance bridge 滚动式竖旋桥 | roller bascule bridge 滚动式竖旋桥 | roller bearing 滚轴支座

bridge seat：桥支座

bridge seam weld ==> 桥缝焊接,桥线焊 | bridge seat ==> 桥支座 | bridge sensitivity ==> 电桥灵敏度

bridge floor system：桥面系为提供列车、车辆、人群通过而设置桥面所需要的结构系统

bridge superstructure桥跨结构(上部结构)桥的支承部分以上或拱桥... | bridge floor system桥面系为提供列车、车辆、人群通过而设置桥面所需要的结构系统. | bridge bearing; bridge support桥支座支承桥跨结构,并将其...