- 更多网络例句与板材相关的网络例句 [注：此内容来源于网络，仅供参考]
-
When the timber, to buy home plate to be placed 10 days to allow them to adapt to the home temperature, humidity, and then started the winter decoration particular attention to the north with land areas warming must not flat on the ground plate, so that a result of the ground baking sheet bow up and cause economic losses.
当木材、板材买回家后要放置十几天，让它们适应家里的温、湿度，然后再开工，冬季装修尤其要注意，北方有地暖的地方千万不要把板材平放在地面上，这样板材会因地面烘烤弓起来造成经济损失。
-
Presents the suitable materials and size for the capillary decorative panel for heating, based on the experimental data, analyses the thermal performance of this kind of panels, and puts forward the heat release calculation formula and selection method of it.
介绍了毛细管供热饰板材的选材及样本的结构尺寸，结合实验数据分析了毛细管供热饰板材的热工性能，给出了毛细管供热饰板材的散热量计算公式及设计选择方法。
-
A steel plate having a tensile strength of at least about 930 MPa (135Ksi), a toughness as measured by Charpy V-notch impact test at least about 120 joules (88 ft-lb), and a microstructure comprising at least about 90 volume percent of a mixture of fine-grained lower bainite and fine-grained lath martensite, wherein at least about 2/3 of said mixture consists of fine-grained lower bainite transformed from unrecrystallized austenite having an average grain size of less than about 10 microns and comprising iron and specified weight percentages of the additives: carbon, silicon, manganese, copper, nickel, niobium, titanium, aluminum, calcium,rare earth metals, and magnesium, is prepared by heating a steel slab to a suitable temperature; reducing the slab to form plate in one or more hot rolling passes (10) in a first temperature range in which austenite recrystallizes; further reducing said plate in one or more hot rolling passes (10) in a second temperature range in which austenite does not recrystallize, quenching (12) said plate to a suitable quench stop temperature (16); and stopping said quenching and allowing said plate to air cool (18) to ambient temperature.
一种钢板，其抗拉强度至少约930MPa135ksi），在－40℃（－40°F）下，采用夏氏V型缺口冲击试验测定的韧性至少约120焦耳（88英尺－磅），并且其显微组织包含至少约90％体积的细晶粒的下贝氏体和细晶粒的板条马氏体的混合物，其中该混合物的至少约2／3由从平均粒径小于约10微米的未再结晶奥氏体转变而来的细晶粒的下贝氏体组成，而且，其中所述的钢板包含铁和特定重量百分比的添加元素：碳、硅、锰、铜、镍、铌、钛、铝、钙、稀土金属和镁，所述钢的制备过程为：将一钢板坯加热至一个适当的温度；在奥氏体可发生再结晶的第一个温度范围内，采用一个或多个热轧道次（10），将所述板坯轧制成板材；在奥氏体不发生再结晶的第二个温度范围，采用一个或多个热轧道次（10）进一步轧制所述板材；将所述板材淬火处理（12）至一个适当的淬火终止温度（16）；停止所述淬火处理并将所述板材空冷（18）至室温。
-
An ultra-high strength, weldable, low alloy steel with excellent cryogenic temperature toughness in the base plate and in the heat affected zone when welded, having a tensile strength greater than 830 MPa (120 ksi) and a micro-laminate microstructure comprising austenite film layers and fine-grained martensite/lower bainite laths, is prepared by heating a steel slab comprising iron and specified weight percentages of some or all of the additives carbon, manganese, nickel, nitrogen, copper, chromium, molybdenum, silicon, niobium, vanadium, titanium, aluminum, and boron; reducing the slab to form plate in one or more passes in a temperature range in which austenite recrystallizes; finish rolling the plate in one or more passes in a temperature range below the austenite recrystallization temperature and above the Ar3 transformation temperature; quenching the finish rolled plate to a suitable Quench Stop Temperature; stopping the quenching; and either, for a period of time, holding the plate substantially isothermally at the QST or slow-cooling the plate before air cooling, or simply air cooling the plate to ambient temperature.
在基体板以及焊接时的热影响区处的低温韧性优异的超高强度、可焊接、低合金钢具有高于830MPa（120ksi）的抗拉强度，并且具有包含奥氏体薄膜层和细晶粒的马氏体／下贝氏体板条的显微层状组织，所述钢的制备过程为：加热含有铁以及特定重量百分比的添加元素的钢坯，所述添加元素为碳，锰，镍，氮，铜，铬，钼，硅，铌，钒，钛，铝，以及硼中的一些或全部；在奥氏体可发生再结晶的温度范围内，采用一个或多个道次，将所述钢坯轧制成板材；在低于奥氏体再结晶温度但高于Ar 3 转变点的温度下，采用一个或多个道次对所述板材进行终轧；将所述终轧板材淬火至一适当淬火终止温度；停止所述淬火；或者在空冷前在QST点基本等温保持所述板材一段时间，或者对所述板材进行缓慢冷却，或者只是简单地将所述板材空冷至室温。
-
A circle shear device for cutting holes in sheet metal as in claim 1 wherein: a said upper center shaft includes a first platform member disposed rotatably connected adjacent a lower end of said upper center shaft for supporting a top surface of said provided metal sheet; b said lower center shaft includes a second platform member disposed rotatably connected adjacent an upper end of said lower center shaft for supporting a bottom surface of said provided metal sheet; and c said upper and lower support platform members engaging top and bottom surfaces of said provided metal sheet to prevent metal sheet movement when said cutter wheels are brought into shearing contact with said provided metal sheet.
一个圈剪切装置切割孔金属板材作为权利要求1 ，其中： A ）表示，上中心轴，包括第一次会员平台弃置rotatably连接相邻较低月底上说，中心轴为支持一个顶面的表示，提供金属板材； B ）表示，较低的中心轴，包括第二个平台会员弃置rotatably连接相邻上月底表示，较低的中心轴为支持一个底部表面的说，提供金属板材； C ）表示，上，下支撑平台成员从事顶部和底部表面的表示，提供金属板，以防止金属板运动时说，刀车轮被带入剪切接触说，提供金属板材。
-
In order to reduce ships when the plate between the equipment and the plate friction, has used the roller transmission, causes between the equipment and the plate friction way becomes the rolling friction, maximum limit reduced in the equipment work to the plate attrition.
为了减少在板材运送时设备与板材之间的摩擦，采用了辊传动，使设备与板材之间的摩擦方式变为滚动摩擦，最大限度的减小了设备工作中对板材的磨损。
-
Common rolling plank is shown intense (orientaton of 0002) tool reference plane, after rolling of horn waiting for diameter, plank grain orientaton by original (change of orientaton of 0002) tool reference plane is; of orientaton of blame tool reference plane the existence after strain crack of common rolling plank is many twin brilliant, amount of brilliant of twin of drawing of direction of rolling of edge of plank of rolling of horn w
普通轧制板材呈强烈的(0002)基面取向，等径角轧制后，板材晶粒取向由原来的(0002)基面取向转变为非基面取向；普通轧制板材拉伸断裂后存在大量孪晶，等径角轧制板材沿轧制方向拉伸孪晶数量明显减少，等径角轧制有可能启动了新的滑移系，而拉伸孪生只是作为一种协调变形机制。
-
The forming limit diagram relates to strain paths, then the forming limit diagram made in linear strain path can not be directly used to complex strain paths.
根据试验测定的不锈钢板材成形极限图用理论方法建立了不锈钢板材的成形极限应力图，其真实板材成形极限图和成形极限应力图均是一条直线，只有这样板材成形才能满足塑性变形体积不变条件。
-
Indoor air sources of formaldehyde are mainly in the following aspects : 1, the plywood used for interior decoration, Ximugongban, medium density fibreboard and shaving board, and other artificial plate because formaldehyde has strong sexual bond, has strengthened plate and the hardness control, corrosion functions, Therefore, the current production of imitation board use Jiaonianji merits to formaldehyde as the main ingredients thiourea aldehyde resins, plate, residual and did not participate in the response formaldehyde will gradually release of the surrounding environment is a indoor air formaldehyde main ;2, using imitation board manufacturing furniture, some manufacturers in the pursuit of profit, the use of unqualified plate. In preliminary front face material reuse inferior glue, the manufacturing processes are not standardized, as a result of customers buying home, to buy a small emission points ;3, containing formaldehyde content and may distribute to the outside other categories decorative materials, such as stickers Qiangbu, with wallpapers, chemical fiber carpet, foam, paint and paint, etc.;4, combustion, emit formaldehyde certain materials, such as cigarettes and some organic materials.
室内空气中的甲醛来源主要有以下几个方面：1、用作室内装饰的胶合板、细木工板、中密度纤维板和刨花板等人造板材，因为甲醛具有较强的粘合性，还具有加强板材的硬度及防虫、防腐的功能，所以目前生产人造板使用的胶粘剂是非曲直以甲醛为主要成分的脲醛树脂，板材中残留的和未参与反应的甲醛会逐渐向周围环境释放，是形成室内空气中甲醛的主体；2、用人造板制造的家具，一些厂家为了追求利润，使用不合格的板材，在粘接贴面材料时再使用劣质胶水，制造工艺不规范，结果顾客买回家去，等于买回了一个小型废气排放站；3、含有甲醛成分并有可能向外界散发的其他各类装饰材料，比如贴墙布，贴墙纸，化纤地毯、泡沫塑料、油漆和涂料等；4、燃烧后会散发甲醛的某些材料，比如香烟及一些有机材料。
-
Now have a new dry granite mines, sheet plant, Shangrao granite mines, sheet plant, Dexing granite mines, sheet plant each one, forming an annual output of 30,000 cubic meters of granite blocks, an annual output of granite, marble plates 600,000 square meters of the scale, with the processing stone table, stone chair, stone railings, stone lions, mushroom, lychee board, fire board, polished column, Roman column, stone carving, Curb, sidewalk boards and other special-shaped stone processing capacity.
现拥有新干花岗岩矿山、板材厂，上饶花岗岩矿山、板材厂，德兴花岗岩矿山、板材厂各一个，形成了年产花岗岩荒料3万立方米，年产花岗岩、大理石板材60万平方米的规模，具备了加工石桌、石椅、石栏杆、石狮、蘑菇石、荔枝板、火烧板、磨光圆柱、罗马柱、石材雕刻、路沿石、人行道板等异形石材加工能力。
- 更多网络解释与板材相关的网络解释 [注：此内容来源于网络，仅供参考]
-
board foot：板材容积单位平方英尺
board foot 板材容积单位 | board foot 板材容积单位平方英尺 | board foot 板英尺
-
board measure：板材量尺
board log 航海日志 | board measure 板材量尺 | board measurement feet 板材量尺
-
plank：板材
锯材又分方木( square timber )、板材( plank )和规格材( dimension lumber ). 方木是指直角锯切且宽厚比小于 3 的,截面为矩形或正方形的锯材. 板材是指宽度为厚度 3 倍或 3 倍以上的矩形锯材. 规格材是指按轻型木结构设计的需要,
-
planking：板材船壳板甲板铺板装镶木板工作
planking 板材船壳板 | planking 板材船壳板甲板铺板装镶木板工作 | planking 外板
-
Mangles：(板材)矫直辊
mandrel unit(水压机)穿孔装置 | mangles(板材)矫直辊 | mangle辊式板材矫直机
-
Wood-based panels：木基板材
79.040 Wood, sawlogs and sawn timber 木材、原木和锯材 | 79.060 Wood-based panels 木基板材 | 79.060.01 Wood-based panels in general 木基板材综合
-
straightening machine：板材矫直机
Continuous casting板材连铸连轧机 | Straightening machine板材矫直机 | Straightening roll 平整机
-
veneered wood：裝潢片材;蒙皮板材
shop lumber 再加工板材 | veneered wood 裝潢片材;蒙皮板材 | oriented strand board 定向纖維板;定向拼合板
-
plate-punching machine：冲板机,板材冲床
plate pinch 压板 | plate punching machine 冲板机,板材冲床 | plate roll 板材轧辊
-
shop lumber：再加工板材
engineered lumber 工程木 | shop lumber 再加工板材 | veneered wood 裝潢片材;蒙皮板材