曲柄行程

词组短语

crank throw · throw of crank

与曲柄行程相关的网络例句 [注：此内容来源于网络，仅供参考]

The method of setting up an affine coordinates system to solve the problems for the spatial crank and rocker mechanism is proposed.

分析并回顾了在给定摇杆两个极限位置及行程速度变化系数的情况下，最小传动角为最大的平面曲柄摇杆机构和空间曲柄摇杆机构的设计问题。

The article bases on the traditional graphical method,and applies design principle in the references[1],derives the optimizing design methods which under the condition of meeting the fixed slider stroke and the coefficient of variety of stroke velocity,makes the minimum transmission angle of the eccentric crank slider mechanism to maximum(that is the best transmission angle).

曲柄滑块机构在工程上应用十分广泛，传动角的大小是衡量机构传力性能好坏的一个重要指标。通常求解最佳传动角的方法是建立数学模型，在计算机上进行数值求解，本文在传统图解法的基础上，运用文献[1]中的设计原理，推导出在满足给定的滑块行程S和行程速度变化系数K的条件下，使传动

This paper made an improvement and development on the traditional graphic solution method for designing planar crank-rocker mechanism in accordance with travel velocity-ratio coefficient K .

对传统的按行程速比系数K设计平面曲柄摇杆机构的图解法做了改进，使该法在解决带有辅助条件的设计问题时更为简捷。

By making use of contraction mapping principle and similar matrices and graphical method ,this paper discusses some methods of asking its limit in accordance with recurrent sequence of number.3. The criteria whether Ⅰ,Ⅱ,Ⅲ types of crank-rocker mechanisms exist are given and the graphical method of synthesizing crank-rocker mechanisms with quick return characteristics are proposed.

针对目前具有急回特性的曲柄摇杆机构综合中存在的不足，对这类机构的图解法综合进行了深入的探讨，得到了行程速比系数和摇杆摆角取不同值时，Ⅰ型、Ⅱ型、Ⅲ型曲柄摇杆机构是否有解的判据，并给出用图解法综合具有急回特性的曲柄摇杆机构的方法。

Cutting machine used crank slider, and switches used itinerary electromagnet with the realization of the fixed-length wire control.

切断机采用了曲柄滑块机构，采用行程开关和电磁铁配合的方式实现线材的定长控制。

Crank endplay device should be used in long work piece changing in to thin stretching process,the device will make gliding block to be realized un iform motion in working process.

在长工件变薄拉伸加工中应选用曲柄—摇杆机构，此机构能使滑块在工作行程中实现平稳的匀速运动，并可获得较高的工件表面质量。

与曲柄行程相关的网络解释 [注：此内容来源于网络，仅供参考]

Bottom dead center：下止点

上止点(Top Dead Center) 活塞离曲轴旋转中心最远的位置 下止点(Bottom Dead Center) 活塞离曲轴旋转中心最近的位置 活塞行程S 上下止点之间的距离 曲柄半径R 曲轴旋转中心到曲柄销中心的距离 气缸工作容积V S (单位 L) 活塞由上止点运动到下止点,

throw into gear：啮合

throw feed 贯穿进给 | throw into gear 啮合 | throw of crank 曲柄行程

throwoff：切断

throwofcrank 曲柄行程 | throwoff 切断 | throwoffhook 脱钩

crank up：转动曲柄起动

crank travel 曲柄行程 | crank up 转动曲柄起动 | crank vessel 易倾船

crank up：曲柄回转,曲轴回转,转动曲柄起动

487. crank travel 曲柄行程 | 488. crank up 曲柄回转,曲轴回转,转动曲柄起动 | 489. crank vessel 易倾船,易倾性船

needle bar plate：针板

needle bar crank ==> 针杆曲柄=>針棒クランク | needle bar plate ==> 针板 | needle bar stroke ==> 针杆行程

crank throw：曲柄行程

crank throw 曲柄半径 | crank throw 曲柄行程 | crank travel 曲柄行程

crank throw：曲柄半径

crank starter 起动曲柄 | crank throw 曲柄半径 | crank throw 曲柄行程

crank throw：曲柄行程,曲柄半径

483. crank tap ==> 曲柄钻丝锥 | 484. crank throw ==> 曲柄行程,曲柄半径 | 485. crank thrust bearing ==> 曲轴推力轴承