- 更多网络例句与曲柄传动的相关的网络例句 [注：此内容来源于网络，仅供参考]
-
The method of setting up an affine coordinates system to solve the problems for the spatial crank and rocker mechanism is proposed.
分析并回顾了在给定摇杆两个极限位置及行程速度变化系数的情况下，最小传动角为最大的平面曲柄摇杆机构和空间曲柄摇杆机构的设计问题。
-
The article bases on the traditional graphical method,and applies design principle in the references[1],derives the optimizing design methods which under the condition of meeting the fixed slider stroke and the coefficient of variety of stroke velocity,makes the minimum transmission angle of the eccentric crank slider mechanism to maximum(that is the best transmission angle).
曲柄滑块机构在工程上应用十分广泛，传动角的大小是衡量机构传力性能好坏的一个重要指标。通常求解最佳传动角的方法是建立数学模型，在计算机上进行数值求解，本文在传统图解法的基础上，运用文献[1]中的设计原理，推导出在满足给定的滑块行程S和行程速度变化系数K的条件下，使传动
-
View showing one way of attaching crank note that crank has been removed and reinserted into crank tube to enable the crank frame to be rotated 180 degrees and still have the chain drive on the right side.
检视显示单程附加曲轴曲柄注意到，已删除和重新融入曲柄管，使曲柄范围内，以180度旋转，并仍然有链传动的右侧。
-
On the basis of the equivalent mechanism of swinging movable teethed transmission-crank-rocker mechanism, the tooth profile equation of central gear was derived by the use of complex numbered vector method.
基于摆动活齿传动的等效机构－曲柄摇杆机构，利用复数矢量法，导出了中心轮的齿廓方程。
-
Torque control mechanism: Uses the worm bearing adjuster axial to flee moves, on the worm shaft is loaded with the small dish reed, flees the worm bearing adjuster axial moves through the crank drive to the torque axis, again touches the switch through the cam the principle.
4转矩控制机构：采用蜗杆轴向窜动，蜗杆轴上装有碟簧、把蜗杆的轴向窜动通过曲柄传动到转矩轴，再通过凸轮触动开关的原理。
-
The eccentricity wheel organ connect with power output belt pulley which comes from the front end of chassis transmission box through one belt transmission. It adopts the combined geared clutch.
割刀由装在偏心轮曲柄上的滚轮直接驱动刀条上的滑槽来运动，偏心轮机构通过一级皮带传动与底盘传动箱前端的动力输出皮带轮相连，离合器采用结合子式齿型离合器。
-
The eccentricity wheel organ connect with power output belt pulley which comes from the front end of chassis transmission box through one belt transmission. It adopts the combined geared clutch. The clutch controls the moving blade and switch controls the accelerograph.
割刀由装在偏心轮曲柄上的滚轮直接驱动刀条上的滑槽来运动，偏心轮机构通过一级皮带传动与底盘传动箱前端的动力输出皮带轮相连，离合器采用结合子式齿型离合器。
-
Because of the fact, the bearing capacity of the whole drive cannot be developed well enough. To improve the performances of the load-capacity, transmission efficiency, and reliability of mechanical drive, we originally developed some designs of the double crank ring-plate-type cycloid planetary drive. The new-type drive keeps all the natural advantages, which is of multi-tooth mesh, small mesh angle, and hardened tooth flank of gears. Moreover, The drive does not need the special output unit as the ring-plate-type drive does, so that the rigidity of the output shaft becomes much higher. Since the tumbler bearing is placed outside the cycloidal gear, the size of the bearing is no longer restricted to any extent.
为大幅度提高其承载能力、传动效率和可靠性诸指标，我们创新研究出来的多种结构双曲柄环板式针摆行星传动，其特点是不仅保留着原摆线针轮行星减速器同时啮合齿数多，总法向力与总圆周力间夹角小，摆线轮与针轮齿均为硬齿面等本质上的优点；而且又具有环板式传动省去输出机构且输出轴刚性好，转臂轴承移至行星轮外，从而传递的转矩可以成倍提高的优点。
-
Second, oil does not come into contact with the compressed gas external drive mechanism, such as in reciprocating compressor crankcase parts, crank pin, crank bearings, connecting rod slide, slide, crosshead; and speed rotary compressor bearings , gear and other growth.
其二为油不与压缩气体接触的外部传动机构，如往复式压缩机曲轴箱中零件、曲柄销、曲柄轴承、连杆滑块、滑道、十字头；回转式和速度式压缩机的轴承、增速齿轮等。
-
The construction of said movable connection seat is one of these: actuating mechanism cpmposed of generator, gearing wheel and guide screw; crank, rod drive construction or cylinder, rod drive construction.
所述的反弹板的活动连接座在电机、传动齿轮、丝杆组成的传动结构，曲柄、连杆传动结构或者气缸、连杆传动结构中选择一种。
- 更多网络解释与曲柄传动的相关的网络解释 [注：此内容来源于网络，仅供参考]
-
crank-driven：曲柄传动的
492. crank web deflection ==> 臂距差 | 493. crank-driven ==> 曲柄传动的 | 494. crank-guide ==> 曲柄导向装置,连杆