- 更多网络例句与斜接合相关的网络例句 [注：此内容来源于网络，仅供参考]
-
Create another miter joint at the other tube junction.
在其他细管接合处建立其他斜接接合。
-
All angles, offsets, and other changes in alignment of railings shall be made with accurately mitered joints.
排成一条直线的栏杆中，任何角度、偏移和其他变化都应为准确的斜接合。
-
The inboard end of the rod is axially slidably engaged with the inboard rod to accommodate variances in the relative positions between the outboard and inboard recliners due to build tolerances in the seat assembly and the vehicle.
杆的内侧端部与内侧杆接合可适应外侧与内侧斜调机构之间的相对位置因坐椅组件和车辆制造偏差所造成的差异。
-
The research results showed that (1) inelastic compressive behavior of the gusset plate was similar to a cantilever plate in compression load,(2) buckling strength was reasonably predicted based on an inelastic plate buckling equation and buckling coefficient, and (3) design guidelines of the gusset plate in compression were proposed with inclusions of edge stiffeners.
本研究结果显示：(1)含挫屈束制消能斜撑之接合板在受轴压作用下，将产生的挫屈模式为Fixed-Free、(2)接合板在Fixed-Free模式下之挫屈强度预测及(3)如何加劲接合板使其强度能达到降伏后之非弹性挫屈行为。
-
The research, therefore, aimed to investigate buckling strength and inelastic compressive behavior of the gusset plate with various geometry, edge stiffeners, and boundary conditions. A parametric study was performed by the general purpose nonlinear finite element computer program ABAQUS.
因此本研究将著重在研究钢骨消能斜撑系统之接合板受轴压力下之力学行为，以有限元素分析程式ABAQUS分析含挫屈束制钢骨消能斜撑之一层楼构架之强度及行为，并针对其加劲板进行有限元素分析之参数研究，藉由改变其加劲板的尺寸与后度来探讨对接合板强度之影响。
-
The arrangement of braces is X type. The braces is H175x175x11x7.5, same as the second test of TCBF. Because of additional knife plates, the braces length in this test is a little shorter than the second TCBF test. The gusset plate design use the UFM instead of ellipse bending design method.
试体高6.66公尺，宽6.7公尺，斜撑排列形式为大X形，斜撑尺寸为H175x175x11x7.5，与第二次TCBF试验采用之斜撑相同，但本研究因需配置额外的连接板而使得斜撑长度略短，接合板则采用规范建议之UFM进行设计，与第二次TCBF椭圆形凹折设计不同。
-
Help the discussions above is useful for the relative research in the future. From experiment, we found the gussets buckle without stiffeners. After adding stiffeners at the edges of gusset, the buckling of gussets never occurred.
试验过程当中发现斜撑之接合板在未加劲之下会产生挫屈的现象，而在加劲过后挫屈现象便受到有效的控制，分析中发现亦可以缩短斜撑端部与所接梁柱之距离来避免接合板挫屈的发生。
- 更多网络解释与斜接合相关的网络解释 [注：此内容来源于网络，仅供参考]
-
oblique butt joint：斜對接合
障礙標線 Object marking | 斜對接合 Oblique butt joint | 斜溝 Oblique gutter
-
miter mitre joint：斜接合
miter mitre gear等径伞齿轮 | miter mitre joint斜接合 | miter mitre valve锥形阀
-
mitre joint：斜接
mitre block 斜接,斜面接合块 | mitre joint 斜接 | multiply 繁殖, 乘, 增加
-
mitre block：斜接,斜面接合块
missing 故障,损失,遗漏 | mitre block 斜接,斜面接合块 | mitre joint 斜接
-
oblique projection：斜轴投影
斜支距 Oblique offset | 斜軸投影 Oblique projection | 斜嵌接合 Oblique scarf joint
-
Oblique scarf joint：斜嵌接合
斜軸投影 Oblique projection | 斜嵌接合 Oblique scarf joint | 洪流觀測 Observation,flood flow
-
splice joint：编交接合
防测挡板 splash shield | 斜交接合 splayed joint | 编交接合 splice joint
-
Cogged joint：雄榫接合
雄榫cog | 雄榫接合cogged joint | 雄榫斜嵌接合cogged-scarf joint
-
mitered joint：斜接合
雾气清除机 mist eliminator | 斜接合 mitered joint | 伤害减轻 mitigation of hazards
-
splayed joint：斜交接合
"阿基米德蜗线","spiral of Archimedes" | "斜交接合","splayed joint" | "栓槽","spline"